B40940B8107M000

Aluminum electrolytic capacitors Hybrid polymer aluminum electrolytic capacitors, very high ripple current – up to 145 °C Series/Type: B40940 Date: July 2023  TDK Electronics AG 2023. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without TDK Electronics’ prior express consent is prohibited. Hybrid polymer aluminum electrolytic capacitors Very high ripple current – up to 145 °C SMD capacitors Long-life grade capacitors Applications  Automotive electronics  Industrial electronics Features         Miniaturized dimensions Long useful life, 4000 h at 135 °C High operating temperature capability up to 145 °C Very high ripple current capability Very low ESR Low ESR across temperature range Suitable for reflow soldering RoHS-compatible Construction     Surface mount device Coated aluminum case Minus pole marking on the case Case with pressure relief vent Delivery mode  Taped on reel Please read Cautions and warnings and Important notes at the end of this document. 2 7/23 B40940 Hybrid polymer aluminum electrolytic capacitors Very high ripple current – up to 145 °C B40940 Specifications and characteristics in brief Rated voltage VR Surge voltage VS 63 V DC 1.15 VR Rated capacitance CR Capacitance tolerance 82 ... 120 µF 20% ^ = M Dissipation factor tan  (20 °C, 120 Hz) VR (V DC) tan  (max.) 63 0.08 Leakage current Ileak (20 °C, 2 min) or 3 µA, whichever is greater Useful life1) Requirements: 125 °C; VR; IAC,R > 4000 h |C/C|  30% of initial value 135 °C; VR; IAC,max > 4000 h ESR  2 times initial specified limit2) 145 °C; VR; IAC,max > 2000 h Ileak  initial specified limit Voltage endurance test 125 °C; VR 1000 h Post test requirements: life3) Shelf 125 °C, 0 V Biased humidity test 85 °C, 85% RH, VR |C/C|  15% of initial value tan   1.5 times initial specified limit Ileak  initial specified limit Requirements: 1000 h |C/C|  30% of initial value tan   2 times initial specified limit Ileak  initial specified limit Requirements: 2000 h |C/C|  30% of initial value tan   2 times initial specified limit Ileak  initial specified limit Vibration resistance test To AEC-Q200 (MIL-STD-202, Method 204): Frequency range 10 Hz … 2 kHz, displacement amplitude max. 1.5 mm, acceleration max. 5 g, duration 3 x 20 min, 12 cycles. Capacitor soldered on standard TDK PCB. IEC climatic category To IEC 60068-1:2013: 40/125/56 (–40 °C/+125 °C/56 days damp heat test) Reference standard AEC-Q200 REV D4) 1) Refer to chapter "General technical information, 5 Useful life" on how to interpret useful life. 2) ESRmax at 100 kHz, 20 °C 3) Before the measurement, the capacitor shall be preconditioned by the application of the rated voltage for 1 hour. The voltage shall be applied to the capacitor through a resistor, the value of which shall be approximately 100 . 4) Refer to chapter "General technical information, 2 Standards and specifications" for further details. Please read Cautions and warnings and Important notes at the end of this document. 3 7/23 Hybrid polymer aluminum electrolytic capacitors Very high ripple current – up to 145 °C Dimensional drawing Layout recommendation Dimensions and weights Dimensions (mm) Approx. weight d 0.5 l 0.3 g 10 10.2 1.4 10 12.5 1.6 Please read Cautions and warnings and Important notes at the end of this document. 4 7/23 B40940 Hybrid polymer aluminum electrolytic capacitors Very high ripple current – up to 145 °C B40940 Overview of available types Other voltage and capacitance ratings are available upon request. VR (V DC) 63 Case dimensions d x l (mm) CR (µF) 82 10 x 10.2 100 10 x 10.2 10 x 12.5 120 10 x 12.5 Technical data and ordering codes CR 120 Hz 20 °C µF Case dimenions dxl mm ESRmax 100 kHz 20 C  IAC,R 100 kHz 125 °C A IAC,max 100 kHz 135 °C A IAC,max 100 kHz 145 °C A Ordering code (composition see below) VR = 63 V DC 82 10 x 10.2 0.030 2.8 1.5 1.0 B40940A8826M000 100 10 x 10.2 0.030 2.8 1.5 1.0 B40940A8107M000 100 10 x 12.5 0.022 3.4 1.8 1.3 B40940B8107M000 120 10 x 12.5 0.022 3.4 1.8 1.3 B40940A8127M000 Please read Cautions and warnings and Important notes at the end of this document. 5 7/23 Hybrid polymer aluminum electrolytic capacitors Very high ripple current – up to 145 °C B40940 Marking Package details Dimensions, weights and packing units Case size d x l (mm) H ±0.2 (mm) Parts per reel Reels per box Box dimensions (mm) 10 x 10.2 11.2 500 5 400 x 405 x 230 10 x 12.5 13.8 400 5 400 x 405 x 230 Please read Cautions and warnings and Important notes at the end of this document. 6 7/23 Hybrid polymer aluminum electrolytic capacitors Very high ripple current – up to 145 °C Soldering profile Recommended reflow soldering conditions Useful life1) 1) Depending on ambient temperature TA under ripple current operating condition at VR – refer to chapter "General technical information, 5 Useful life" on how to interpret useful life. Please read Cautions and warnings and Important notes at the end of this document. 7 7/23 B40940 Hybrid polymer aluminum electrolytic capacitors Very high ripple current – up to 145 °C Frequency factor of permissible ripple current IAC versus frequency f Please read Cautions and warnings and Important notes at the end of this document. 8 7/23 B40940 Hybrid polymer aluminum electrolytic capacitors Very high ripple current – up to 145 °C B40940 Cautions and warnings Personal safety The electrolytes used have been optimized both with a view to the intended application and with regard to health and environmental compatibility. They do not contain any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide (DMAC). Furthermore, some of the high-voltage electrolytes used are self-extinguishing. As far as possible, we do not use any dangerous chemicals or compounds to produce operating electrolytes, although in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no alternative materials are currently known. We do, however, restrict the amount of dangerous materials used in our products to an absolute minimum. Materials and chemicals used in our aluminum electrolytic capacitors are continuously adapted in compliance with the TDK Electronics Corporate Environmental Policy and the latest EU regulations and guidelines such as RoHS, REACH/SVHC, GADSL, and ELV. MDS (Material Data Sheets) are available on our website for all types listed in the data book. MDS for customer specific capacitors are available upon request. MSDS (Material Safety Data Sheets) are available for our electrolytes upon request. Nevertheless, the following rules should be observed when handling aluminum electrolytic capacitors: No electrolyte should come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected areas immediately with running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical treatment. Avoid inhaling electrolyte vapor or mists. Workplaces and other affected areas should be well ventilated. Clothing that has been contaminated by electrolyte must be changed and rinsed in water. Please read Cautions and warnings and Important notes at the end of this document. 9 7/23 Hybrid polymer aluminum electrolytic capacitors Very high ripple current – up to 145 °C B40940 Product safety The table below summarizes the safety instructions that must be observed without fail. A detailed description can be found in the relevant sections of seperate file chapter "General technical information". Topic Safety information Reference chapter "General technical information" Polarity Make sure that polar capacitors are connected with the right polarity. 1 "Basic construction of aluminum electrolytic capacitors" Reverse voltage Voltages of opposite polarity should be prevented by connecting a diode. 3.1.6 "Reverse voltage" Mounting position of capacitors with screw or multi-pin terminals Multi-pin capacitors with pressure relief vent on the can base must not be mounted with terminals facing up unless otherwise specified. 11.1 "Mounting positions of capacitors with screw or multi-pin terminals" Robustness of terminals The following maximum tightening torques must 11.2 not be exceeded when connecting screw terminals: "Mounting torques" M5: 2.5 Nm M6: 4.0 Nm Mounting of single-ended capacitors The internal structure of single-ended capacitors might be damaged if excessive force is applied to the lead wires. Avoid any compressive, tensile or flexural stress. Do not move the capacitor after soldering to PC board. Do not pick up the PC board by the soldered capacitor. Do not insert the capacitor on the PC board with a hole space different to the lead space specified. 11.3 "Mounting considerations for single-ended capacitors" Soldering Do not exceed the specified time or temperature limits during soldering. 11.5 "Soldering" Soldering, cleaning agents Do not allow halogenated hydrocarbons to come into contact with aluminum electrolytic capacitors. 11.6 "Cleaning agents" Upper category temperature Do not exceed the upper category temperature. 7.2 "Maximum permissible operating temperature" Passive flammability Avoid external energy, e.g. fire. 8.1 "Passive flammability" Please read Cautions and warnings and Important notes at the end of this document. 10 7/23 Hybrid polymer aluminum electrolytic capacitors Very high ripple current – up to 145 °C B40940 Topic Safety information Reference chapter "General technical information" Active flammability Avoid overload of the capacitors. 8.2 "Active flammability" Maintenance Make periodic inspections of the capacitors. Before the inspection, make sure that the power supply is turned off and carefully discharge the capacitors. Do not apply excessive mechanical stress to the capacitor terminals when mounting. 10 "Maintenance" Storage Do not store capacitors at high temperatures or high humidity. Capacitors should be stored at +5 to +35 °C and a relative humidity of  75%. 7.3 "Shelf life and storage conditions" Reference chapter "Capacitors with screw terminals" Breakdown strength of insulating sleeves Do not damage the insulating sleeve, especially when ring clips are used for mounting. "Screw terminals – accessories" Display of ordering codes for TDK Electronics products The ordering code for one and the same product can be represented differently in data sheets, data books, other publications, on the company website, or in order-related documents such as shipping notes, order confirmations and product labels. The varying representations of the ordering codes are due to different processes employed and do not affect the specifications of the respective products. Detailed information can be found on the Internet under www.tdk-electronics.tdk.com/orderingcodes. Please read Cautions and warnings and Important notes at the end of this document. 11 7/23 Hybrid polymer aluminum electrolytic capacitors Very high ripple current – up to 145 °C B40940 Symbols and terms Symbol C CR CS CS,T Cf d dmax ESL ESR ESRf ESRT f I IAC IAC,RMS IAC,f IAC,max IAC,R Ileak Ileak,op l lmax R Rins Rsymm T T TA TB TC t t tb V VF Vop VR VS XC English Capacitance Rated capacitance Series capacitance Series capacitance at temperature T Capacitance at frequency f Case diameter, nominal dimension Maximum case diameter Self-inductance Equivalent series resistance Equivalent series resistance at frequency f Equivalent series resistance at temperature T Frequency Current Alternating current (ripple current) Root-mean-square value of alternating current Ripple current at frequency f Maximum permissible ripple current Rated ripple current Leakage current Operating leakage current Case length, nominal dimension Maximum case length (without terminals and mounting stud) Resistance Insulation resistance Balancing resistance Temperature Temperature difference Ambient temperature Capacitor base temperature Case temperature Time Period Service life (operating hours) Voltage Forming voltage Operating voltage Rated voltage, DC voltage Surge voltage Capacitive reactance Please read Cautions and warnings and Important notes at the end of this document. 12 German Kapazität Nennkapazität Serienkapazität Serienkapazität bei Temperatur T Kapazität bei Frequenz f Gehäusedurchmesser, Nennmaß Maximaler Gehäusedurchmesser Eigeninduktivität Ersatzserienwiderstand Ersatzserienwiderstand bei Frequenz f Ersatzserienwiderstand bei Temperatur T Frequenz Strom Wechselstrom Wechselstrom, Effektivwert Wechselstrom bei Frequenz f Maximal zulässiger Wechselstrom Nennwechselstrom Reststrom Betriebsreststrom Gehäuselänge, Nennmaß Maximale Gehäuselänge (ohne Anschlüsse und Gewindebolzen) Widerstand Isolationswiderstand Symmetrierwiderstand Temperatur Temperaturdifferenz Umgebungstemperatur Temperatur des Gehäusebodens Gehäusetemperatur Zeit Zeitraum Brauchbarkeitsdauer (Betriebszeit) Spannung Formierspannung Betriebsspannung Nennspannung, Gleichspannung Spitzenspannung Kapazitiver Blindwiderstand 7/23 Hybrid polymer aluminum electrolytic capacitors Very high ripple current – up to 145 °C Symbol XL Z ZT tan   0 r  B40940 English Inductive reactance Impedance Impedance at temperature T Dissipation factor Failure rate German Induktiver Blindwiderstand Scheinwiderstand Scheinwiderstand bei Temperatur T Verlustfaktor Ausfallrate Absolute permittivity Relative permittivity Angular frequency; 2   f Elektrische Feldkonstante Dielektrizitätszahl Kreisfrequenz; 2   f Note: All dimensions are given in mm. Please read Cautions and warnings and Important notes at the end of this document. 13 7/23 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, we are either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether a product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.tdk-electronics.tdk.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to our General Terms and Conditions of Supply. 14 7/23 Important notes 7. Our manufacturing sites serving the automotive business apply the IATF 16949 standard. The IATF certifications confirm our compliance with requirements regarding the quality management system in the automotive industry. Referring to customer requirements and customer specific requirements (“CSR”) TDK always has and will continue to have the policy of respecting individual agreements. Even if IATF 16949 may appear to support the acceptance of unilateral requirements, we hereby like to emphasize that only requirements mutually agreed upon can and will be implemented in our Quality Management System. For clarification purposes we like to point out that obligations from IATF 16949 shall only become legally binding if individually agreed upon. 8. The trade names EPCOS, CarXield, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CTVS, DeltaCap, DigiSiMic, FilterCap, FormFit, InsuGate, LeaXield, MediPlas, MiniBlue, MiniCell, MKD, MKK, ModCap, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine, PQvar, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, ThermoFuse, WindCap, XieldCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.tdk-electronics.tdk.com/trademarks. Release 2023-07 15 7/23