Aluminum electrolytic capacitors
Snap-in capacitors
Series/Type:
B41505
Date:
December 2016
© EPCOS AG 2016. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
EPCOS AG is a TDK Group Company.
Snap-in capacitors
B41505
Excellent performance 105 °C
Long-life grade capacitors
Applications
Professional power supplies
Features
Long useful life
High reliability
Outstanding ripple current capability
Low ESR
Capacitors pass the needle flame test according to
IEC 60695-11-5 for all flame exposure times up to 120 s
RoHS-compatible
Construction
Charge/discharge-proof, polar
Aluminum case, fully insulated with PVC
Snap-in solder pins to hold component in place on PC-board
Minus pole marking on case surface
Minus pole not insulated from case
Overload protection by safety vent on the base
Terminals
Standard version with 2 terminals,
2 lengths available: 6.3 and 4.5 mm
3 terminals to ensure correct insertion: length 4.5 mm
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 17
B41505
Excellent performance 105 °C
Specifications and characteristics in brief
Rated voltage VR
Surge voltage VS
Rated capacitance CR
Capacitance tolerance
10 ... 100 V DC
1.15 VR
560 ... 33000 μF
±20% M
Dissipation factor tan δ
(20 °C, 100 Hz)
VR = 10 V DC: tan δ ≤ 0.20
VR = 16 V DC: tan δ ≤ 0.15
VR = 25 V DC: tan δ ≤ 0.11
VR = 35 V DC: tan δ ≤ 0.10
VR = 50 V DC: tan δ ≤ 0.08
VR = 63 ... 100 V DC: tan δ ≤ 0.06
Leakage current Ileak
(5 min, 20 °C)
Self-inductance ESL
Approx. 20 nH
1)
Useful life
105 °C; VR; IAC,R
85 °C; VR; IAC,max
40 °C; VR; 2.1 IAC,R
Load life test
105 °C; VR; IAC,R
Voltage endurance test
105 °C; VR
Vibration resistance
test
Characteristics at low
temperature
> 5000 h
> 12000 h
> 25000 h
4000 h
2000 h
Requirements:
ΔC/C
≤ 45% of initial value
tan δ
≤ 3 times initial specified limit
Ileak
≤ initial specified limit
Post test requirements:
ΔC/C
≤ 20% of initial value
tan δ
≤ 2 times initial specified limit
Ileak
≤ initial specified limit
Post test requirements:
ΔC/C
≤ 15% of initial value
tan δ
≤ 1.3 times initial specified limit
Ileak
≤ initial specified limit
To IEC 60068-2-6, test Fc:
Frequency range 10 Hz ... 55 Hz, displacement amplitude 0.35 mm,
acceleration max. 5 g, duration 3 × 2 h.
Capacitor mounted by its body which is rigidly clamped to the work
surface.
Max. impedance
Z -25 °C / Z 20 °C
2
ratio at 120 Hz
Z -40 °C / Z 20 °C
3
IEC climatic category
To IEC 60068-1: 40/105/56 (40 °C/+105 °C/56 days damp heat test)
Sectional specification
IEC 60384-4
1) Refer to chapter "General technical information, 5 Useful life" on how to interpret useful life.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 17
B41505
Excellent performance 105 °C
Dimensional drawings
Snap-in capacitors with standard insulation (PVC)
Snap-in terminals, length (6.3 ±1) mm.
Also available in a shorter version with a
length of (4.5 1) mm. Safety vent on the
base.
Snap-in capacitors are also available with
3 terminals (length (4.5 1) mm). Safety vent
on the base.
Dimensions (mm)
d +1
l ±2
22
25
22
30
22
35
22
40
25
25
25
30
25
35
25
40
Dimensions (mm)
d +1
l ±2
30
25
30
30
30
35
30
40
30
45
30
50
35
35
35
40
35
45
35
50
Approx.
weight (g)
Packing
units (pcs.)
9
12
15
18
13
17
19
22
160
160
160
160
130
130
130
130
Please read Cautions and warnings and
Important notes at the end of this document.
Page 4 of 17
Approx.
weight (g)
Packing
units (pcs.)
17
23
29
36
41
46
36
41
56
70
80
80
80
80
80
80
60
60
60
60
B41505
Excellent performance 105 °C
Ordering codes for terminal styles and insulation features
Identification in 3rd block of ordering code
Snap-in capacitors
Terminal version
Insulation version
PVC
Standard terminals 6.3 mm
M000
Short terminals 4.5 mm
M007
3 terminals 4.5 mm
M002
Ordering examples:
B41505A5109M007
B41505A5109M002
}
}
snap-in capacitor with short terminals
snap-in capacitor with 3 terminals
Please read Cautions and warnings and
Important notes at the end of this document.
Page 5 of 17
B41505
Excellent performance 105 °C
Overview of available types
The capacitance and voltage ratings listed below are available in different case sizes upon
request. Other voltage and capacitance ratings are also available upon request.
VR (V DC)
10
16
25
35
50
63
80
100
Case dimensions d × l (mm)
CR (μF)
560
25 × 25
680
22 × 35
22 × 25
1000
25 × 25
25 × 35
30 × 30
30 × 25
1200
1500
22 × 35
25 × 35
30 × 40
2200
22 × 25
22 × 35
25 × 35
30 × 30
30 × 35
30 × 50
3300
22 × 30
25 × 25
25 × 35
30 × 40
35 × 35
35 × 50
22 × 30
25 × 25
22 × 40
30 × 35
35 × 35
35 × 45
35 × 50
4700
6800
22 × 25
22 × 30
25 × 30
25 × 40
30 × 50
10000
22 × 30
25 × 30
25 × 40
30 × 40
35 × 45
15000
22 × 40
25 × 40
30 × 40
35 × 40
35 × 45
18000
22000
30 × 35
33000
30 × 45
30 × 40
Please read Cautions and warnings and
Important notes at the end of this document.
Page 6 of 17
B41505
Excellent performance 105 °C
Technical data and ordering codes
CR
100 Hz
20 °C
μF
Case
dimensions
d×l
mm
VR = 10 V DC
22 × 25
6800
22 × 30
10000
22 × 40
15000
30 × 35
22000
30 × 45
33000
VR = 16 V DC
22 × 30
6800
25 × 30
10000
25 × 40
15000
30 × 40
22000
VR = 25 V DC
22 × 30
4700
25 × 25
4700
25 × 30
6800
25 × 40
10000
30 × 40
15000
VR = 35 V DC
22 × 25
2200
22 × 30
3300
25 × 25
3300
22 × 40
4700
25 × 40
6800
30 × 40
10000
35 × 40
15000
35 × 45
18000
VR = 50 V DC
22 × 35
2200
25 × 35
3300
30 × 35
4700
30 × 50
6800
35 × 45
10000
ESRtyp
100 Hz
20 °C
mΩ
Zmax
10 kHz
20 °C
mΩ
IAC,max
100 Hz
60 °C
A
IAC,max
100 Hz
85 °C
A
IAC,R1)
Ordering code
100 Hz (composition see
105 °C below)
A
74
53
37
26
19
78
56
39
28
20
3.6
4.6
5.9
7.7
10.2
2.8
3.6
4.6
6.0
7.8
1.4
1.8
2.3
3.0
3.9
B41505A3688M00#
B41505A3109M00#
B41505A3159M00#
B41505A3229M00#
B41505A3339M00#
46
34
24
17
49
36
26
18
4.6
5.6
7.1
9.4
3.6
4.4
5.6
7.0
1.8
2.2
2.8
3.5
B41505A4688M00#
B41505A4109M00#
B41505A4159M00#
B41505A4229M00#
53
53
41
30
22
57
57
43
32
23
4.1
4.1
4.8
6.4
8.2
3.2
3.2
3.8
5.0
6.4
1.6
1.6
1.9
2.5
3.2
B41505A5478M00#
B41505F5478M00#
B41505A5688M00#
B41505A5109M00#
B41505A5159M00#
85
56
56
45
35
26
19
17
90
60
60
48
37
28
20
18
2.8
3.8
3.8
4.8
5.9
7.4
9.4
11.1
2.2
3.0
3.0
3.8
4.6
5.8
7.6
8.6
1.1
1.5
1.5
1.9
2.3
2.9
3.8
4.3
B41505A7228M00#
B41505A7338M00#
B41505F7338M00#
B41505A7478M00#
B41505A7688M00#
B41505A7109M00#
B41505A7159M00#
B41505A7189M00#
85
56
42
33
25
90
60
45
35
26
3.6
4.6
5.6
7.4
9.4
2.8
3.6
4.4
5.8
7.2
1.4
1.8
2.2
2.9
3.6
B41505A6228M00#
B41505A6338M00#
B41505A6478M00#
B41505A6688M00#
B41505A6109M00#
Composition of ordering code
# = Terminal style
0 = snap-in standard terminals (6.3 mm)
2 = snap-in 3 terminals (4.5 mm)
7 = snap-in short terminals (4.5 mm)
1) 120-Hz conversion factor of ripple current: IAC (120 Hz) = 1.03 IAC (100 Hz)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 7 of 17
B41505
Excellent performance 105 °C
Technical data and ordering codes
CR
100 Hz
20 °C
μF
Case
dimensions
d×l
mm
VR = 63 V DC
22 × 25
1000
22 × 35
1500
25 × 35
2200
30 × 30
2200
30 × 40
3300
35 × 35
4700
35 × 50
6800
VR = 80 V DC
25 × 25
1000
30 × 25
1200
25 × 35
1500
30 × 35
2200
35 × 35
3300
35 × 45
4700
VR = 100 V DC
25 × 25
560
22 × 35
680
25 × 35
1000
30 × 30
1000
30 × 40
1500
30 × 50
2200
35 × 50
3300
IAC,max
100 Hz
85 °C
A
IAC,R2)
Ordering code
100 Hz (composition see
105 °C below)
A
2.6
3.6
4.3
4.6
5.9
6.9
9.4
2.0
2.8
3.4
3.6
4.6
5.4
7.2
1.0
1.4
1.7
1.8
2.3
2.7
3.6
B41505A8108M00#
B41505A8158M00#
B41505A8228M00#
B41505F8228M00#
B41505A8338M00#
B41505A8478M00#
B41505A8688M00#
133
110
89
60
48
34
3.3
3.8
4.6
5.1
7.1
8.5
2.6
3.0
3.6
4.0
5.6
6.8
1.3
1.5
1.8
2.0
2.8
3.4
B41505A0108M00#
B41505A0128M00#
B41505A0158M00#
B41505A0228M00#
B41505A0338M00#
B41505A0478M00#
190
156
106
106
70
60
40
2.6
3.1
3.6
3.8
4.8
5.9
7.7
2.0
2.4
2.8
3.0
3.8
4.6
6.0
1.0
1.2
1.4
1.5
1.9
2.3
3.0
B41505A9567M00#
B41505A9687M00#
B41505A9108M00#
B41505F9108M00#
B41505A9158M00#
B41505A9228M00#
B41505A9338M00#
ESRtyp
100 Hz
20 °C
mΩ
Zmax
10 kHz
20 °C
mΩ
149
100
68
80
53
42
29
159
106
72
85
56
45
31
125
104
83
56
45
32
178
146
100
100
66
56
38
IAC,max
100 Hz
60 °C
A
Composition of ordering code
# = Terminal style
0 = snap-in standard terminals (6.3 mm)
2 = snap-in 3 terminals (4.5 mm)
7 = snap-in short terminals (4.5 mm)
2) 120-Hz conversion factor of ripple current: IAC (120 Hz) = 1.03 IAC (100 Hz)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 8 of 17
B41505
Excellent performance 105 °C
Useful life1)
depending on ambient temperature TA under ripple current operating conditions
Frequency factor of permissible ripple
current IAC versus frequency f
Frequency characteristic of ESR
Typical behavior
1) Refer to chapter "General technical information, 5 Useful life" on how to interpret useful life.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 17
B41505
Excellent performance 105 °C
Impedance Z versus frequency f
Typical behavior at 20 °C
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 17
B41505
Excellent performance 105 °C
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have been optimized both with a view to the intended
application and with regard to health and environmental compatibility. They do not contain any
solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide
(DMAC).
Furthermore, some of the high-voltage electrolytes used by EPCOS are self-extinguishing.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce
operating electrolytes, although in exceptional cases, such materials must be used in order to
achieve specific physical and electrical properties because no alternative materials are currently
known. We do, however, restrict the amount of dangerous materials used in our products to an
absolute minimum.
Materials and chemicals used in EPCOS aluminum electrolytic capacitors are continuously
adapted in compliance with the EPCOS Corporate Environmental Policy and the latest EU
regulations and guidelines such as RoHS, REACH/SVHC, GADSL, and ELV.
MDS (Material Data Sheets) are available on the EPCOS website for all types listed in the data
book. MDS for customer specific capacitors are available upon request.
MSDS (Material Safety Data Sheets) are available for all of our electrolytes upon request.
Nevertheless, the following rules should be observed when handling aluminum electrolytic
capacitors: No electrolyte should come into contact with eyes or skin. If electrolyte does come
into contact with the skin, wash the affected areas immediately with running water. If the eyes
are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical
treatment. Avoid inhaling electrolyte vapor or mists. Workplaces and other affected areas should
be well ventilated. Clothing that has been contaminated by electrolyte must be changed and
rinsed in water.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 17
B41505
Excellent performance 105 °C
Product safety
The table below summarizes the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic
Polarity
Reverse voltage
Mounting
position of screwterminal capacitors
Robustness of
terminals
Mounting of
single-ended
capacitors
Soldering
Soldering,
cleaning agents
Upper category
temperature
Passive
flammability
Safety information
Reference
chapter "General
technical information"
Make sure that polar capacitors are connected
1
with the right polarity.
"Basic construction of
aluminum electrolytic
capacitors"
Voltages of opposite polarity should be prevented 3.1.6
by connecting a diode.
"Reverse voltage"
Screw terminal capacitors must not be mounted
11.1.
with terminals facing down unless otherwise
"Mounting positions of
specified.
capacitors with screw
terminals"
The following maximum tightening torques must
11.3
not be exceeded when connecting screw
"Mounting torques"
terminals:
M5: 2.5 Nm
M6: 4.0 Nm
The internal structure of single-ended capacitors 11.4
might be damaged if excessive force is applied to "Mounting
the lead wires.
considerations for
Avoid any compressive, tensile or flexural stress. single-ended capacitors"
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
Do not exceed the specified time or temperature 11.5
limits during soldering.
"Soldering"
Do not allow halogenated hydrocarbons to come 11.6
into contact with aluminum electrolytic capacitors. "Cleaning agents"
Do not exceed the upper category temperature.
7.2
"Maximum permissible
operating temperature"
Avoid external energy, e.g. fire.
8.1
"Passive flammability"
Please read Cautions and warnings and
Important notes at the end of this document.
Page 12 of 17
B41505
Excellent performance 105 °C
Topic
Safety information
Active
flammability
Maintenance
Avoid overload of the capacitors.
Storage
Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
capacitors.
Do not apply excessive mechanical stress to the
capacitor terminals when mounting.
Do not store capacitors at high temperatures or
high humidity. Capacitors should be stored at
+5 to +35 °C and a relative humidity of ≤ 75%.
Breakdown strength Do not damage the insulating sleeve, especially
of insulating
when ring clips are used for mounting.
sleeves
Reference
chapter "General
technical information"
8.2
"Active flammability"
10
"Maintenance"
7.3
"Shelf life and storage
conditions"
Reference
chapter "Capacitors with
screw terminals"
"Screw terminals
accessories"
Display of ordering codes for EPCOS products
The ordering code for one and the same product can be represented differently in data sheets,
data books, other publications and the website of EPCOS, or in order-related documents such as
shipping notes, order confirmations and product labels. The varying representations of the ordering codes are due to different processes employed and do not affect the specifications of the respective products.
Detailed information can be found on the Internet under www.epcos.com/orderingcodes.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 13 of 17
B41505
Excellent performance 105 °C
Symbols and terms
Symbol
English
German
C
CR
CS
CS,T
Cf
d
dmax
ESL
ESR
ESRf
Capacitance
Rated capacitance
Series capacitance
Series capacitance at temperature T
Capacitance at frequency f
Case diameter, nominal dimension
Maximum case diameter
Self-inductance
Equivalent series resistance
Equivalent series resistance at
frequency f
Equivalent series resistance at
temperature T
Frequency
Current
Alternating current (ripple current)
Root-mean-square value of alternating
current
Ripple current at frequency f
Maximum permissible ripple current
Rated ripple current
Leakage current
Operating leakage current
Case length, nominal dimension
Maximum case length (without
terminals and mounting stud)
Resistance
Insulation resistance
Balancing resistance
Temperature
Temperature difference
Ambient temperature
Case temperature
Capacitor base temperature
Time
Period
Service life (operating hours)
Kapazität
Nennkapazität
Serienkapazität
Serienkapazität bei Temperatur T
Kapazität bei Frequenz f
Gehäusedurchmesser, Nennmaß
Maximaler Gehäusedurchmesser
Eigeninduktivität
Ersatzserienwiderstand
Ersatzserienwiderstand bei Frequenz f
ESRT
f
I
IAC
IAC,RMS
IAC,f
IAC,max
IAC,R
Ileak
Ileak,op
l
lmax
R
Rins
Rsymm
T
ΔT
TA
TC
TB
t
Δt
tb
Please read Cautions and warnings and
Important notes at the end of this document.
Ersatzserienwiderstand bei Temperatur T
Frequenz
Strom
Wechselstrom
Wechselstrom, Effektivwert
Wechselstrom bei Frequenz f
Maximal zulässiger Wechselstrom
Nennwechselstrom
Reststrom
Betriebsreststrom
Gehäuselänge, Nennmaß
Maximale Gehäuselänge (ohne Anschlüsse
und Gewindebolzen)
Widerstand
Isolationswiderstand
Symmetrierwiderstand
Temperatur
Temperaturdifferenz
Umgebungstemperatur
Gehäusetemperatur
Temperatur des Gehäusebodens
Zeit
Zeitraum
Brauchbarkeitsdauer (Betriebszeit)
Page 14 of 17
B41505
Excellent performance 105 °C
Symbol
V
VF
Vop
VR
VS
XC
XL
Z
ZT
tan δ
λ
ε0
εr
ω
English
Voltage
Forming voltage
Operating voltage
Rated voltage, DC voltage
Surge voltage
Capacitive reactance
Inductive reactance
Impedance
Impedance at temperature T
Dissipation factor
Failure rate
Absolute permittivity
Relative permittivity
Angular velocity; 2 π f
German
Spannung
Formierspannung
Betriebsspannung
Nennspannung, Gleichspannung
Spitzenspannung
Kapazitiver Blindwiderstand
Induktiver Blindwiderstand
Scheinwiderstand
Scheinwiderstand bei Temperatur T
Verlustfaktor
Ausfallrate
Elektrische Feldkonstante
Dielektrizitätszahl
Kreisfrequenz; 2 π f
Note
All dimensions are given in mm.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 15 of 17
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As a
rule we are either unfamiliar with individual customer applications or less familiar with them than
the customers themselves. For these reasons, it is always ultimately incumbent on the customer
to check and decide whether a product with the properties described in the product specification is
suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very high
level of operational safety and especially in customer applications in which the malfunction or
failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of the
customer application or other action taken by the customer (e.g. installation of protective circuitry
or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or
failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material
Data Sheets on the Internet (www.tdk-electronics.tdk.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently,
we cannot guarantee that all products named in this publication will always be available.
The aforementioned does not apply in the case of individual agreements deviating from the
foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to our General Terms
and Conditions of Supply.
7. Our manufacturing sites serving the automotive business apply the IATF 16949 standard.
The IATF certifications confirm our compliance with requirements regarding the quality
management system in the automotive industry. Referring to customer requirements and
customer specific requirements (“CSR”) TDK always has and will continue to have the policy of
respecting individual agreements. Even if IATF 16949 may appear to support the acceptance of
unilateral requirements, we hereby like to emphasize that only requirements mutually agreed
upon can and will be implemented in our Quality Management System. For clarification
purposes we like to point out that obligations from IATF 16949 shall only become legally binding if
individually agreed upon.
Page 16 of 17
Important notes
8. The trade names EPCOS, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CTVS,
DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD, MKK,
MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine, PQvar,
SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, ThermoFuse,
WindCap are trademarks registered or pending in Europe and in other countries. Further
information will be found on the Internet at www.tdk-electronics.tdk.com/trademarks.
Release 2018-10
Page 17 of 17