B43545B9337M000

Aluminum electrolytic capacitors Snap-in capacitors Series/Type: B43545 Date: December 2019 © TDK Electronics AG 2019. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without TDK Electronics' prior express consent is prohibited. Snap-in capacitors B43545 Outstanding ripple current, long useful life  105 °C Long-life grade capacitors Applications Servo drives Frequency converters Solar inverters Uninterruptible power supplies Professional power supplies Medical appliances Not for automotive applications unless otherwise specified Features Outstanding ripple current capability Improved charge/discharge robustness Base cooling available upon request for case sizes with diameters of 30 to 35 mm and lengths of 35 to 55 mm Long useful life Very high CV product, long useful life High reliability Extremely improved performance at high frequencies Outstanding low ESR at operating conditions above 50 °C Optimized internal thermal resistance Capacitors with all insulation versions pass the needle flame test according to IEC 60695-11-5 for all flame exposure times up to 120 s RoHS-compatible Construction Rapid charge/discharge-proof, polar Aluminum case, fully insulated with PET Version with PVC insulation available upon request Version with PVC insulation and additional PET insulation cap on terminal side available for insulating the capacitor from the PCB Snap-in solder pins to hold component in place on PC-board Minus pole marking on case surface Minus pole not insulated from case Overload protection by safety vent on the case wall Terminals Standard version with 2 terminals, 2 lengths available: 6.3 and 4.5 mm 3 terminals to ensure correct insertion: length 4.5 mm Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 19 B43545 Outstanding ripple current, long useful life  105 °C Specifications and characteristics in brief Rated voltage VR Surge voltage VS Rated capacitance CR Capacitance tolerance Dissipation factor tan δ (20 °C, 120 Hz) 400 ... 500 V DC 1.10  VR 68 ... 1000 μF ±20%  M VR = 400 V DC: tan δ ≤ 0.15 VR ≥ 450 V DC: tan δ ≤ 0.20 Leakage current Ileak (5 min, 20 °C) Self-inductance ESL 1) Approx. 20 nH Useful life 105 °C; VR; IAC,R > 5000 h Voltage endurance test 105 °C; VR 2000 h Requirements: ΔC/C ≤ 20% of initial value tan δ ≤ 2 times initial specified limit Ileak ≤ initial specified limit Post test requirements: ΔC/C ≤ 10% of initial value tan δ ≤ 1.3 times initial specified limit Ileak ≤ initial specified limit Rapid charge/discharge > 50 million cycles ≤ 35 °C; ΔV ≤ 150 V; 6 Hz Requirements: ΔC/C ≤ 20% of initial value tan δ ≤ 2 times initial specified limit Ileak ≤ initial specified limit VR = 400 ... 450 V; l ≤ 55 mm Vibration resistance test Characteristics at low temperature To IEC 60068-2-6, test Fc: Frequency range 10 Hz ... 55 Hz, displacement amplitude 0.35 mm, acceleration max. 5 g, duration 3 × 2 h. Capacitor mounted by its body which is rigidly clamped to the work surface. Max. impedance VR 400 V 450 V 500 V ratio at 100 Hz Z -25 °C / Z 20 °C 3 5 7 Z -40 °C / Z 20 °C 7 10 20 IEC climatic category To IEC 60068-1: VR ≤ 450: 40/105/56 (40 °C/+105 °C/56 days damp heat test) VR = 500: 25/105/56 (25 °C/+105 °C/56 days damp heat test) The capacitors can be operated in the temperature range of 40 °C but the impedance at 40 °C must be taken into consideration. Sectional specification IEC 60384-4 1) Refer to chapter "General technical information, 5 Useful life" on how to interpret useful life. Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 19 B43545 Outstanding ripple current, long useful life  105 °C Dimensional drawings Snap-in capacitors with standard insulation (PET) Dimensions (mm) d +1 l ±2 25 25 25 30 25 35 25 40 25 45 25 50 25 55 Approx. weight (g) Packing units (pcs.) 13 17 19 22 25 29 32 130 130 130 130 130 130 130 Snap-in terminals, length (6.3 ±1) mm. Also available in a shorter version with a length of (4.5 1) mm. Insulation is marked with "PET" on the sleeve. Safety vent on the case wall. Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 19 B43545 Outstanding ripple current, long useful life  105 °C Snap-in capacitors are also available with 3 terminals (length (4.5 1) mm). Insulation is marked with "PET" on the sleeve. Safety vent on the case wall. Please read Cautions and warnings and Important notes at the end of this document. Dimensions (mm) d +1 l ±2 30 25 30 30 30 35 30 40 30 45 30 50 30 55 30 60 30 65 30 70 30 75 30 80 35 25 35 30 35 35 35 40 35 45 35 50 35 55 35 60 35 65 35 70 35 75 35 80 Page 5 of 19 Approx. weight (g) 17 23 29 36 41 46 53 58 64 69 74 80 22 29 36 41 56 70 81 90 102 115 128 142 Packing units (pcs.) 80 80 80 80 80 80 80 60 60 60 60 60 60 60 60 60 60 60 60 36 36 36 36 36 B43545 Outstanding ripple current, long useful life  105 °C Snap-in capacitors with PVC insulation and PET insulation cap on terminal side Snap-in terminals, length (6.3 +1/1.4) mm. Also available in a shorter version with a length of (4.5 1.4) mm. PET insulation cap is positioned under the insulation sleeve. Safety vent on the case wall. Dimensions (mm) Approx. Packing d +1.4 l +2.2/2 weight (g) units (pcs.) 25 25 13 115 25 30 17 115 25 35 19 115 25 40 22 115 25 45 25 115 25 50 29 115 25 55 32 115 Please read Cautions and warnings and Important notes at the end of this document. Snap-in capacitors are also available with 3 terminals (length (4.5 1.4) mm). PET insulation cap is positioned under the insulation sleeve. Safety vent on the case wall. Dimensions (mm) Approx. Packing d +1.4 l +2.2/2 weight (g) units (pcs.) 30 25 17 80 30 30 23 80 30 35 29 80 30 40 36 80 30 45 41 80 30 50 46 80 30 55 53 80 35 25 22 60 35 30 29 60 35 35 36 60 35 40 41 60 35 45 56 60 35 50 70 60 35 55 81 60 Page 6 of 19 B43545 Outstanding ripple current, long useful life  105 °C Packing of snap-in capacitors For ecological reasons the packing is pure cardboard. Ordering codes for terminal styles and insulation features Identification in 3rd block of ordering code Snap-in capacitors Terminal version Insulation version PET PVC plus PET cap Standard terminals 6.3 mm M060 M080 Short terminals 4.5 mm M067 M087 3 terminals 4.5 mm M062 M082 Ordering examples: B43545A5107M067 B43545A5107M062 B43545A5107M080 } } } snap-in capacitor with short terminals and PET insulation snap-in capacitor with 3 terminals and PET insulation snap-in capacitor with standard terminals and PVC insulation with additional PET insulation cap on terminal side Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 19 B43545 Outstanding ripple current, long useful life  105 °C Overview of available types The capacitance and voltage ratings listed above are available in different case sizes upon request. Other voltage and capacitance ratings are also available upon request. VR (V DC) 400 450 500 Case dimensions d × l (mm) CR (μF) 25 × 25 68 82 25 × 25 25 × 30 100 25 × 30 25 × 35 30 × 25 120 25 × 25 25 × 35 30 × 25 25 × 35 30 × 30 150 25 × 30 25 × 40 30 × 30 25 × 45 30 × 35 35 × 25 180 25 × 35 30 × 25 25 × 45 30 × 35 35 × 25 25 × 50 30 × 35 35 × 30 220 25 × 35 30 × 30 25 × 50 30 × 35 35 × 30 25 × 55 30 × 40 35 × 35 270 25 × 45 30 × 35 35 × 25 30 × 45 35 × 35 30 × 50 35 × 40 330 25 × 50 30 × 35 35 × 30 30 × 50 35 × 40 30 × 55 35 × 45 390 25 × 55 30 × 40 35 × 35 30 × 55 35 × 45 35 × 50 470 30 × 50 35 × 40 30 × 65 35 × 50 35 × 55 560 30 × 55 35 × 40 30 × 75 35 × 55 680 30 × 70 35 × 50 35 × 70 820 30 × 80 35 × 55 35 × 80 1000 35 × 70 Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 19 B43545 Outstanding ripple current, long useful life  105 °C Technical data and ordering codes CR 100 Hz 20 °C μF Case dimensions d×l mm VR = 400 V DC 25 × 25 120 25 × 30 150 25 × 35 180 30 × 25 180 25 × 35 220 30 × 30 220 25 × 45 270 30 × 35 270 35 × 25 270 25 × 50 330 330 30 × 35 35 × 30 330 25 × 55 390 30 × 40 390 35 × 35 390 30 × 50 470 35 × 40 470 560 30 × 55 35 × 40 560 30 × 70 680 35 × 50 680 30 × 80 820 35 × 55 820 35 × 70 1000 ESRtyp 100 Hz 20 °C mΩ 500 400 330 330 270 270 220 220 220 180 180 180 160 150 150 130 130 110 110 95 90 80 75 65 ESRtyp 300 Hz 60 °C mΩ 160 130 110 100 90 85 70 70 75 60 55 60 50 50 50 40 40 34 36 28 30 24 26 20 Zmax 10 kHz 20 °C mΩ 700 550 460 460 380 370 310 300 310 260 250 260 220 210 220 180 180 150 160 140 130 110 110 100 IAC,max 100 Hz 60 °C A IAC,max 100 Hz 85 °C A IAC,R Ordering code 100 Hz (composition see 105 °C below) A 2.23 2.60 2.96 3.12 3.36 3.58 3.96 4.12 4.15 4.58 4.69 4.79 5.19 5.30 5.38 6.11 6.11 6.95 6.80 8.27 7.87 9.62 8.99 10.7 1.64 1.92 2.19 2.31 2.48 2.64 2.93 3.04 3.06 3.39 3.46 3.54 3.84 3.91 3.98 4.51 4.52 5.13 5.02 6.15 5.82 7.14 6.64 7.95 0.88 1.04 1.18 1.24 1.33 1.42 1.58 1.64 1.65 1.82 1.86 2.03 2.07 2.24 2.28 2.59 2.59 2.94 2.87 3.53 3.33 4.10 3.80 4.56 Composition of ordering code * = Insulation feature #= 6 = PET insulation 8 = PVC insulation with additional PET insulation cap on terminal side Please read Cautions and warnings and Important notes at the end of this document. B43545A9127M0*# B43545A9157M0*# B43545A9187M0*# B43545B9187M0*# B43545A9227M0*# B43545B9227M0*# B43545A9277M0*# B43545B9277M0*# B43545C9277M0*# B43545A9337M0*# B43545B9337M0*# B43545C9337M0*# B43545A9397M0*# B43545B9397M0*# B43545C9397M0*# B43545A9477M0*# B43545B9477M0*# B43545A9567M0*# B43545B9567M0*# B43545B9687M0*# B43545A9687M0*# B43545B9827M0*# B43545A9827M0*# B43545A9108M0*# Terminal style 0 = snap-in standard terminals (6.3 mm) 2 = snap-in 3 terminals (4.5 mm) 7 = snap-in short terminals (4.5 mm) Page 9 of 19 B43545 Outstanding ripple current, long useful life  105 °C Technical data and ordering codes CR 100 Hz 20 °C μF Case dimensions d×l mm VR = 450 V DC 25 × 25 82 25 × 30 100 25 × 35 120 30 × 25 120 25 × 40 150 30 × 30 150 25 × 45 180 30 × 35 180 35 × 25 180 25 × 50 220 220 30 × 35 35 × 30 220 30 × 45 270 35 × 35 270 30 × 50 330 35 × 40 330 30 × 55 390 390 35 × 45 30 × 65 470 35 × 50 470 30 × 75 560 35 × 55 560 35 × 70 680 35 × 80 820 ESRtyp 100 Hz 20 °C mΩ ESRtyp 300 Hz 60 °C mΩ Zmax 10 kHz 20 °C mΩ 1110 910 760 750 610 600 500 500 510 410 410 410 330 340 270 280 230 230 200 190 160 160 140 110 290 240 200 190 160 150 130 130 130 110 110 110 85 90 70 70 60 60 50 50 45 45 36 30 1680 1370 1140 1140 920 910 770 760 770 630 630 630 510 510 420 420 350 360 300 300 250 250 210 180 IAC,max 100 Hz 60 °C A Composition of ordering code * = Insulation feature #= 6 = PET insulation 8 = PVC insulation with additional PET insulation cap on terminal side Please read Cautions and warnings and Important notes at the end of this document. 1.73 2.06 2.34 2.47 2.74 2.86 3.13 3.24 3.32 3.63 3.70 3.82 4.31 4.37 4.98 5.02 5.64 5.63 6.42 6.41 7.39 7.28 8.34 9.62 IAC,max 100 Hz 85 °C A IAC,R Ordering code 100 Hz (composition see 105 °C below) A 1.33 1.52 1.73 1.81 2.02 2.10 2.30 2.38 2.44 2.67 2.72 2.81 3.17 3.22 3.66 3.69 4.15 4.14 4.77 4.72 5.49 5.35 6.20 7.15 0.71 0.82 0.94 0.98 1.09 1.14 1.25 1.29 1.32 1.45 1.47 1.62 1.83 1.85 2.11 2.13 2.39 2.39 2.74 2.72 3.15 3.08 3.56 4.11 B43545B5826M0*# B43545A5107M0*# B43545B5127M0*# B43545A5127M0*# B43545A5157M0*# B43545B5157M0*# B43545A5187M0*# B43545B5187M0*# B43545C5187M0*# B43545A5227M0*# B43545B5227M0*# B43545C5227M0*# B43545A5277M0*# B43545B5277M0*# B43545A5337M0*# B43545B5337M0*# B43545A5397M0*# B43545B5397M0*# B43545B5477M0*# B43545A5477M0*# B43545B5567M0*# B43545A5567M0*# B43545A5687M0*# B43545A5827M0*# Terminal style 0 = snap-in standard terminals (6.3 mm) 2 = snap-in 3 terminals (4.5 mm) 7 = snap-in short terminals (4.5 mm) Page 10 of 19 B43545 Outstanding ripple current, long useful life  105 °C Technical data and ordering codes CR 100 Hz 20 °C μF Case dimensions d×l mm VR = 500 V DC 25 × 25 68 25 × 30 82 25 × 35 100 30 × 25 100 25 × 35 120 30 × 30 120 25 × 45 150 30 × 35 150 35 × 25 150 25 × 50 180 180 30 × 35 35 × 30 180 25 × 55 220 30 × 40 220 35 × 35 220 30 × 50 270 35 × 40 270 330 30 × 55 35 × 45 330 35 × 50 390 35 × 55 470 ESRtyp 100 Hz 20 °C mΩ ESRtyp 300 Hz 60 °C mΩ Zmax 10 kHz 20 °C mΩ 1220 1010 830 820 690 690 550 550 550 460 460 460 380 380 380 310 310 250 250 210 180 340 280 230 220 190 180 150 150 150 130 120 130 100 100 100 85 85 70 70 60 50 1810 1500 1230 1220 1030 1020 820 810 820 690 680 690 560 560 560 460 460 370 380 320 270 IAC,max 100 Hz 60 °C A Composition of ordering code * = Insulation feature #= 6 = PET insulation 8 = PVC insulation with additional PET insulation cap on terminal side Please read Cautions and warnings and Important notes at the end of this document. 1.43 1.73 2.11 2.11 2.42 2.53 2.87 2.97 3.06 3.28 3.34 3.46 3.81 3.84 3.96 4.47 4.53 5.19 5.20 5.84 6.66 IAC,max 100 Hz 85 °C A IAC,R Ordering code 100 Hz (composition see 105 °C below) A 1.22 1.39 1.60 1.68 1.80 1.90 2.14 2.21 2.27 2.44 2.48 2.57 2.83 2.85 2.94 3.33 3.37 3.86 3.86 4.34 4.95 0.61 0.69 0.80 0.84 0.90 0.95 1.07 1.10 1.13 1.22 1.24 1.37 1.41 1.52 1.57 1.77 1.80 2.06 2.06 2.31 2.64 B43545A6686M0*# B43545A6826M0*# B43545A6107M0*# B43545B6107M0*# B43545A6127M0*# B43545B6127M0*# B43545A6157M0*# B43545B6157M0*# B43545C6157M0*# B43545A6187M0*# B43545B6187M0*# B43545C6187M0*# B43545A6227M0*# B43545B6227M0*# B43545C6227M0*# B43545A6277M0*# B43545B6277M0*# B43545A6337M0*# B43545B6337M0*# B43545A6397M0*# B43545A6477M0*# Terminal style 0 = snap-in standard terminals (6.3 mm) 2 = snap-in 3 terminals (4.5 mm) 7 = snap-in short terminals (4.5 mm) Page 11 of 19 B43545 Outstanding ripple current, long useful life  105 °C Useful life1) For useful life calculations, please use our web-based "AlCap Useful Life Calculation Tool", which can be found on the Internet under the following link: www.tdk-electronics.tdk.com/alcap The AlCap Useful Life Calculation Tool provides calculations of useful life as well as additional data for selected capacitor types under operating conditions defined by the user. In addition, it is possible to calculate useful life expectancies based on temperatures measured by the user in the application. Frequency characteristics of ESR Typical behavior Impedance Z versus frequency f Typical behavior at 20 °C 1) Refer to chapter "General technical information, 5 Useful life" on how to interpret useful life. Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 19 B43545 Outstanding ripple current, long useful life  105 °C Cautions and warnings Personal safety The electrolytes used have been optimized both with a view to the intended application and with regard to health and environmental compatibility. They do not contain any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide (DMAC). Furthermore, some of the high-voltage electrolytes used are self-extinguishing. As far as possible, we do not use any dangerous chemicals or compounds to produce operating electrolytes, although in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no alternative materials are currently known. We do, however, restrict the amount of dangerous materials used in our products to an absolute minimum. Materials and chemicals used in our aluminum electrolytic capacitors are continuously adapted in compliance with the TDK Electronics Corporate Environmental Policy and the latest EU regulations and guidelines such as RoHS, REACH/SVHC, GADSL, and ELV. MDS (Material Data Sheets) are available on our website for all types listed in the data book. MDS for customer specific capacitors are available upon request. MSDS (Material Safety Data Sheets) are available for our electrolytes upon request. Nevertheless, the following rules should be observed when handling aluminum electrolytic capacitors: No electrolyte should come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected areas immediately with running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical treatment. Avoid inhaling electrolyte vapor or mists. Workplaces and other affected areas should be well ventilated. Clothing that has been contaminated by electrolyte must be changed and rinsed in water. Please read Cautions and warnings and Important notes at the end of this document. Page 13 of 19 B43545 Outstanding ripple current, long useful life  105 °C Product safety The table below summarizes the safety instructions that must be observed without fail. A detailed description can be found in the relevant sections of seperate file chapter "General technical information". Topic Polarity Reverse voltage Mounting position of screwterminal capacitors Robustness of terminals Mounting of single-ended capacitors Soldering Soldering, cleaning agents Upper category temperature Passive flammability Safety information Reference chapter "General technical information" Make sure that polar capacitors are connected 1 with the right polarity. "Basic construction of aluminum electrolytic capacitors" Voltages of opposite polarity should be prevented 3.1.6 by connecting a diode. "Reverse voltage" Screw terminal capacitors must not be mounted 11.1. with terminals facing down unless otherwise "Mounting positions of specified. capacitors with screw terminals" The following maximum tightening torques must 11.3 not be exceeded when connecting screw "Mounting torques" terminals: M5: 2.5 Nm M6: 4.0 Nm The internal structure of single-ended capacitors 11.4 might be damaged if excessive force is applied to "Mounting the lead wires. considerations for Avoid any compressive, tensile or flexural stress. single-ended capacitors" Do not move the capacitor after soldering to PC board. Do not pick up the PC board by the soldered capacitor. Do not insert the capacitor on the PC board with a hole space different to the lead space specified. Do not exceed the specified time or temperature 11.5 limits during soldering. "Soldering" Do not allow halogenated hydrocarbons to come 11.6 into contact with aluminum electrolytic capacitors. "Cleaning agents" Do not exceed the upper category temperature. 7.2 "Maximum permissible operating temperature" Avoid external energy, e.g. fire. 8.1 "Passive flammability" Please read Cautions and warnings and Important notes at the end of this document. Page 14 of 19 B43545 Outstanding ripple current, long useful life  105 °C Topic Safety information Active flammability Maintenance Avoid overload of the capacitors. Storage Make periodic inspections of the capacitors. Before the inspection, make sure that the power supply is turned off and carefully discharge the capacitors. Do not apply excessive mechanical stress to the capacitor terminals when mounting. Do not store capacitors at high temperatures or high humidity. Capacitors should be stored at +5 to +35 °C and a relative humidity of ≤ 75%. Breakdown strength Do not damage the insulating sleeve, especially of insulating when ring clips are used for mounting. sleeves Reference chapter "General technical information" 8.2 "Active flammability" 10 "Maintenance" 7.3 "Shelf life and storage conditions" Reference chapter "Capacitors with screw terminals" "Screw terminals  accessories" Display of ordering codes for TDK Electronics products The ordering code for one and the same product can be represented differently in data sheets, data books, other publications, on the company website, or in order-related documents such as shipping notes, order confirmations and product labels. The varying representations of the ordering codes are due to different processes employed and do not affect the specifications of the respective products. Detailed information can be found on the Internet under www.tdk-electronics.tdk.com/orderingcodes. Please read Cautions and warnings and Important notes at the end of this document. Page 15 of 19 B43545 Outstanding ripple current, long useful life  105 °C Symbols and terms Symbol English German C CR CS CS,T Cf d dmax ESL ESR ESRf Capacitance Rated capacitance Series capacitance Series capacitance at temperature T Capacitance at frequency f Case diameter, nominal dimension Maximum case diameter Self-inductance Equivalent series resistance Equivalent series resistance at frequency f Equivalent series resistance at temperature T Frequency Current Alternating current (ripple current) Root-mean-square value of alternating current Ripple current at frequency f Maximum permissible ripple current Rated ripple current Leakage current Operating leakage current Case length, nominal dimension Maximum case length (without terminals and mounting stud) Resistance Insulation resistance Balancing resistance Temperature Temperature difference Ambient temperature Case temperature Capacitor base temperature Time Period Service life (operating hours) Kapazität Nennkapazität Serienkapazität Serienkapazität bei Temperatur T Kapazität bei Frequenz f Gehäusedurchmesser, Nennmaß Maximaler Gehäusedurchmesser Eigeninduktivität Ersatzserienwiderstand Ersatzserienwiderstand bei Frequenz f ESRT f I IAC IAC,RMS IAC,f IAC,max IAC,R Ileak Ileak,op l lmax R Rins Rsymm T ΔT TA TC TB t Δt tb Please read Cautions and warnings and Important notes at the end of this document. Ersatzserienwiderstand bei Temperatur T Frequenz Strom Wechselstrom Wechselstrom, Effektivwert Wechselstrom bei Frequenz f Maximal zulässiger Wechselstrom Nennwechselstrom Reststrom Betriebsreststrom Gehäuselänge, Nennmaß Maximale Gehäuselänge (ohne Anschlüsse und Gewindebolzen) Widerstand Isolationswiderstand Symmetrierwiderstand Temperatur Temperaturdifferenz Umgebungstemperatur Gehäusetemperatur Temperatur des Gehäusebodens Zeit Zeitraum Brauchbarkeitsdauer (Betriebszeit) Page 16 of 19 B43545 Outstanding ripple current, long useful life  105 °C Symbol V VF Vop VR VS XC XL Z ZT tan δ λ ε0 εr ω English Voltage Forming voltage Operating voltage Rated voltage, DC voltage Surge voltage Capacitive reactance Inductive reactance Impedance Impedance at temperature T Dissipation factor Failure rate Absolute permittivity Relative permittivity Angular velocity; 2  π  f German Spannung Formierspannung Betriebsspannung Nennspannung, Gleichspannung Spitzenspannung Kapazitiver Blindwiderstand Induktiver Blindwiderstand Scheinwiderstand Scheinwiderstand bei Temperatur T Verlustfaktor Ausfallrate Elektrische Feldkonstante Dielektrizitätszahl Kreisfrequenz; 2  π  f Note All dimensions are given in mm. Please read Cautions and warnings and Important notes at the end of this document. Page 17 of 19 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, we are either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether a product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.tdk-electronics.tdk.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to our General Terms and Conditions of Supply. Page 18 of 19 Important notes 7. Our manufacturing sites serving the automotive business apply the IATF 16949 standard. The IATF certifications confirm our compliance with requirements regarding the quality management system in the automotive industry. Referring to customer requirements and customer specific requirements (“CSR”) TDK always has and will continue to have the policy of respecting individual agreements. Even if IATF 16949 may appear to support the acceptance of unilateral requirements, we hereby like to emphasize that only requirements mutually agreed upon can and will be implemented in our Quality Management System. For clarification purposes we like to point out that obligations from IATF 16949 shall only become legally binding if individually agreed upon. 8. The trade names EPCOS, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CTVS, DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD, MKK, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine, PQvar, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.tdk-electronics.tdk.com/trademarks. Release 2018-10 Page 19 of 19