B43545S7477M001

Aluminum Electrolytic Capacitors Snap-in capacitors Series/Type: Ordering code: B43545 B43545S7477M001 Date: Version: March 18, 2016 2 © EPCOS AG 2016. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Aluminum Electrolytic Capacitors Snap-in capacitors B43545S7477M001 B43545 Preliminary data 105 °C / 5000 h • Outstanding ripple current • compact, long useful life Ordering code: Development code: Customer: B43545S7477M001 PA09536 Capacitor development status Design approved Design under development Dimensions (mm) d+1 35 l±2.5 70 Terminals Snap-in short Without base insulation Technical data Rated capacitance CR 120 Hz, 20 °C Capacitance tolerance 470 µF ±20% Rated voltage VR 550 V Surge voltage VS 605 V Operating temperature range –25 / +105 °C lleak 5 min, 20 °C 1.9 mA Typical ESR ESRtyp 120 Hz, 20 °C 250 mΩ Typical ESR ESRtyp 300 Hz, 60 °C 70 mΩ Maximum dissipation factor tan δ 120 Hz, 20 °C 0.2 Maximum impedance Zmax 10 kHz, 20 °C 410 mΩ Rated ripple current IAC,R 120 Hz, 105 °C 2.5 A IAC,max 120 Hz, 60 °C 6.6 A Maximum leakage current Maximum ripple current Useful life Other specifications 105 °C, VR, IAC,R 5000 h After test: |∆C/C| ≤ 20% of initial value tan δ ≤ 2 x initial spec. limit Ileak ≤ initial spec. limit IEC 60384-4, CECC 30301-809, Data Book 2015, RoHS-compatible Cautions and warnings: see Data Book 2015 or www.epcos.com CAP R&D ALU D / A Please read Important notes at the end of this document. March 18, 2016 Page 2 of 3 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CeraPlas, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, Filter Cap, FormFit, MiniBlue, MiniCell, MDK, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 3 of 3