NTC thermistors for inrush current limiting
Inrush Current Limiters (ICLs)
Series/Type:
Ordering code:
S464/40/M
B57464S 400M
Date:
Version:
2017-07-31
f
Content of header bars 1 and 2 of data sheet will be automatically entered in headers and footers! Please fill in the table and then
change the color to "white". This ensures that the table disappears (invisible) for the customer PDF.
Don't change formatting when entering or pasting text in the table and don't add any cell or line in and to it!
Identification/Classification 1
NTC thermistors for inrush current limiting
(header 1 + top left bar):
Identification/Classification 2
Inrush Current Limiters (ICLs)
(header 2 + bottom left header bar):
Ordering code: (top right header bar)
B57464S 400M
Series/Type: (bottom right header bar)
S464/40/M
Preliminary data (optional):
Data sheet
Department:
PPD VAR PD
Date:
2017-07-31
Version:
f
EPCOS AG 2017. Reproduction, publication and dissemination of this publication, enclosures hereto and the information
contained therein without EPCOS' prior express consent is prohibited.
EPCOS AG is a TDK Group Company.
NTC thermistors for inrush current limiting
Inrush Current Limiters (ICLs)
B57464S 400M
S464/40/M
Data sheet
Application
NTC-thermistor for inrush current limiting in peripheral communication equipment, e.g. in switchmode power supplies.
Features
Black coated thermistor disk
Coating material is flame retardant (UL 94 V-0 approved)
Kinked leads of tinned copper wire
Lead spacing 7.5 mm
High stability of electrical characteristic
Terminals solderable in accordance with IEC 60068-2-20, test ta, method 1
ICL support to fulfill the requirements according EN 61000 of power circuits
Usable in series connections up to 265 Vrms
UL approval (E69802)
CQC approval (CQC09001040539)
RoHS-compatible
PPD VAR PD
Please read Cautions and warnings and
Important notes at the end of this document.
2017-07-31
Page 2 of 12
NTC thermistors for inrush current limiting
Inrush Current Limiters (ICLs)
B57464S 400M
S464/40/M
Data sheet
Drawing
b
27.0 max
mm
th
7.0 max
mm
h
31.0 max
mm
LL
25.0 min
mm
LD
1.0 ±0.05
mm
LS
7.5 ±0.8
mm
1) Seating plane to IEC 60717
Approx. weight: 9 g
General technical data
Climatic category
Max. power
B value
B value tolerance
Resistance tolerance
Rated temperature
Dissipation factor
Thermal cooling time constant
Heat capacity
(IEC 60068-1)
(at 25 °C)
(in air)
(in air)
Pmax
B/B
RR/RR
TR
th
th
Cth
55/170/21
6.7
3450
3
20
W
K
%
%
25
approx. 30
approx. 130
approx. 3900
°C
mW/K
s
mJ/K
Electrical specification and ordering codes
R25
Ω
40
Imax
(0...65 °C)
A
4.4
2)
Ctest
at 230 V AC
μF
2500
Ctest
at 110 V AC
μF
10000
Rmin
(at Imax, 25 °C)
Ω
0.28
Ordering code
B57464S 400M
2) 1200μF at 240V and 4800μF at 120V in UL spec.
PPD VAR PD
Please read Cautions and warnings and
Important notes at the end of this document.
2017-07-31
Page 3 of 12
NTC thermistors for inrush current limiting
Inrush Current Limiters (ICLs)
B57464S 400M
S464/40/M
Data sheet
Maximum continuous current Imax
The Imax denotes the maximum permissible continuous current (DC or RMS values for sine-shaped AC) in the
temperature range from 0 to 65 °C.
Load derating (I / Imax)
The power handling capability of an NTC thermistor cannot be fully utilized over the entire temperature range.
For circuit dimensioning the derating curve given below provides information on the extent to which the current
must be reduced at a certain ambient temperature (TA).
I / Imax
Percent of Imax =
1
T 65 C
100 1 A
Tmax 65 C
TA = ambient temperature ( TA > 65°C )
Tmax = 170°C
-25
0
Ta
170
65
Fig. 1 Maximum current derating (I / Imax )
Maximum permissible capacitance
The currents during turn-on are much higher than the rated currents during continuous operation. To test the
effects of these current surges EPCOS uses the following standard procedure according to IEC 60539-1:
Thyristor
switch
RS
Vload
C test
RT
VNTC
Vload
Ctest
Rs
VNTC
Load voltage [V]
Test capacitance [μF]
Series resistance [Rs = 1 Ω]
Voltage drop across the NTC under test [V]
= 180/375 V
(corresponds (110/230 V + dV) x 1.41)
`
TNT0358-L-E
Fig. 2 Maximum switchable capacity measuring circuit
Marking
EPCOS – logo
Resistance value
NTC
Date code with 4 digits (year and week of production): 1536 (example for week 36 in year 2015)
PPD VAR PD
Please read Cautions and warnings and
Important notes at the end of this document.
2017-07-31
Page 4 of 12
NTC thermistors for inrush current limiting
Inrush Current Limiters (ICLs)
B57464S 400M
S464/40/M
Data sheet
Reliability data
Test
Standard
Test conditions
R25/ R25
(typical)
Remarks
Storage in dry
heat
IEC
60068-2-2
Storage at upper category
temperature
T: 170°C
t: 1 000 h
< 20 %
No visible
damage
Storage in damp
heat, steady
state
IEC
60068-2-78
Temperature of air: 40°C
Relative humidity of air: 93 %
Duration: 21 days
< 20 %
No visible
damage
Rapid change of
temperature
IEC
60068-2-14
Lower test temperature: -55 °C
t: 30 min
Upper test temperature: 170 °C
t: 30 min
Time to change from lower to
upper temperature: < 30 s
Number of cycles: 10
< 20 %
No visible
damage
Endurance with
max. current
IEC
60539-1
< 20 %
No visible
damage
< 20 %
No visible
damage
< 20 %
No visible
damage
Ambient temperature: 25 ±5 °C
I = Imax
t: 1000 h
Ambient temperature: 25 ±5 °C
Cyclic
endurance
IEC
60539-1
Maximum
permissible
capacitance test
IEC
60539-1
I = Imax
On-time = 1 min
Cooling time = 5 min
Number of cycles: 1000
Ambient temperature: 25 ±5 °C
Capacitance = Ctest
Number of cycles: 1000
Note
The self-heating of a thermistor during operation depends on the load applied and the applicable dissipation
factor.
When loaded with maximum allowable current/power and the specified dissipation factor is taken as a basis,
the NTC thermistor may reach a mean temperature of up to 250 C.
The heat developed during operation will also be dissipated through the lead wires. So the contact areas, too,
may become quite hot at maximum load.
When mounting NTC thermistors you have to ensure that there is an adequate distance between the
thermistor and all parts which are sensitive to heat or combustible.
PPD VAR PD
Please read Cautions and warnings and
Important notes at the end of this document.
2017-07-31
Page 5 of 12
NTC thermistors for inrush current limiting
Inrush Current Limiters (ICLs)
B57464S 400M
S464/40/M
Data sheet
Solderability
Test to IEC 60068-2-20
Preconditioning: Immersion into flux F-SW 32.
Evaluation criterion: Wetting of soldering areas ≥95%.
Solder
Bath temperature (℃)
Dwell time (s)
SnAg (3.0 … 4.0), Cu (0.5 … 0.9)
245 ±3
3
Solder
Bath temperature (℃)
Dwell time (s)
SnAg (3.0 … 4.0), Cu (0.5 … 0.9)
260 -5
10
Resistance to soldering heat
Test to IEC 60068-2-20
Preconditioning: Immersion into flux F-SW 32.
Soldering instructions
When soldering, care must be taken that the NTC thermistors are not damaged by excessive heat. The
following maximum temperatures, maximum time spans and minimum distances have to be observed:
Dip soldering
Iron soldering
Bath temperature .
max. 260 ℃
max. 360 ℃
Soldering time
max. 4 s
max. 2 s
Distance from thermistor
min. 6 mm
min. 6 mm
Under more severe soldering conditions the resistance may change.
Robustness of terminations
The leads meet the requirements of IEC 60068-2-21.
Test
Test conditions
Remarks
Tensile strength
Test Ua1: Fasten body with a force applied to each lead
10 N for 10 s
No visible damage
Bending strength
Test Ub: Fasten body with two 90°-bends in opposite
direction at a force of 10 N
No visible damage
Remark: Peel off of coating along the lead is accepted.
PPD VAR PD
Please read Cautions and warnings and
Important notes at the end of this document.
2017-07-31
Page 6 of 12
NTC thermistors for inrush current limiting
Inrush Current Limiters (ICLs)
B57464S 400M
S464/40/M
Data sheet
Resistance versus temperature
1000.0
B57464S 400M
Resistance [Ohm]
100.0
10.0
1.0
0.1
-25
0
25
50
75
100
125
150
175
Temperature [°C]
PPD VAR PD
Please read Cautions and warnings and
Important notes at the end of this document.
2017-07-31
Page 7 of 12
NTC thermistors for inrush current limiting
Inrush Current Limiters (ICLs)
B57464S 400M
S464/40/M
Data sheet
Resistance versus current
2.0
Resistance [Ohm]
1.5
B57464S 400M
1.0
0.5
0.0
0.0
1.0
2.0
3.0
4.0
5.0
Current [A]
PPD VAR PD
Please read Cautions and warnings and
Important notes at the end of this document.
2017-07-31
Page 8 of 12
NTC thermistors for inrush current limiting
Inrush Current Limiters (ICLs)
B57464S 400M
S464/40/M
Data sheet
Packing
Packing
Pcs / unit
Dimensions (mm)
Bulk
200
Approx. x= 80, y= 240, z= 210
Bar code label
The packing of all EPCOS components bears a bar code label stating the type, ordering code, quantity, date of
manufacture and batch number. This enables a component to be traced back through the production process,
together with its batch and test report.
Internal construction
Ceramic
Coating
Metallization
Solder joint
The above picture shows the internal construction of EPCOS ICLs.
Note: Coating may have cracks or chips due to acting mechanical force on the wire, but this does not affect the
performance of the component.
PPD VAR PD
Please read Cautions and warnings and
Important notes at the end of this document.
2017-07-31
Page 9 of 12
NTC thermistors for inrush current limiting
Inrush Current Limiters (ICLs)
B57464S 400M
S464/40/M
Data sheet
Cautions and warnings
See "Important notes" of this data sheet.
Storage
Store thermistors only in original packaging. Do not open the package before storage.
Storage conditions in original packaging: storage temperature -25 °C ... +45 °C, relative humidity ≤75%
annual mean, maximum 95%, dew precipitation is inadmissible.
Avoid contamination of thermistors surface during storage, handling and processing.
Avoid storage of thermistor in harmful environments like corrosive gases (SOx, Cl etc).
Solder thermistors after shipment from EPCOS within the time specified:
- Leaded components: 24 months
Handling
NTC inrush current limiters must not be dropped. Chip-offs must not be caused during handling of NTC
inrush current limiters.
Components must not be touched with bare hands. Gloves are recommended.
Avoid contamination of thermistor surface during handling.
In case of exposure of the NTC inrush current limiters to water, electrolytes or other aggressive media,
these media can penetrate the coating and reach the surface of the ceramic. Low-ohmic or high-ohmic
behavior may occur due to the formation of an electrolyte with metals (silver/lead/tin from metallization or
solder). Low-ohmic behavior is caused by electrochemical migration, high-ohmic behavior by dissolving of
the electrode. In either case, the functionality of the NTC inrush current limiters can not be assured.
Washing processes may damage the product due to the possible static or cyclic mechanical loads (e.g.
ultrasonic cleaning). They may cause cracks to develop on the product and its parts, which might lead to
reduced reliability or lifetime.
Bending / twisting leads
A lead (wire) may be bent at a minimum distance of twice the wire’s diameter plus 4 mm from the
component head or housing. When bending ensure the wire is mechanically relieved at the component
head or housing. The bending radius should be at least 0.75 mm.
Twisting (torsion) by 180°of a lead bent by 90°is permissible at 6 mm from the bottom of the thermistor
body.
Soldering
Use resin-type flux or non-activated flux.
Insufficient preheating may cause ceramic cracks.
Rapid cooling by dipping in solvent is not recommended.
Complete removal of flux is recommended.
PPD VAR PD
Please read Cautions and warnings and
Important notes at the end of this document.
2017-07-31
Page 10 of 12
NTC thermistors for inrush current limiting
Inrush Current Limiters (ICLs)
B57464S 400M
S464/40/M
Data sheet
Mounting
When thermistors are sealed, potted or over-molded, there must be no mechanical stress caused by
thermal expansion during the production process (curing/ over-molding process) and during later operation.
The upper category temperature of the thermistor must not be exceeded. Ensure that the materials used
(sealing / potting compound and plastic material) are chemically neutral.
Electrode must not be scratched before/during/after the mounting process.
Contacts and housings used for assembly with thermistor have to be clean before mounting.
During operation, the inrush current limiters surface temperature can be very high. Ensure that adjacent
components are placed at a sufficient distance from the thermistor to allow for proper cooling of the NTC
inrush current limiters.
Ensure that adjacent materials are designed for operation at temperatures comparable to the surface
temperature of the thermistor. Be sure that surrounding parts and materials can withstand this temperature.
Make sure that inrush current limiters are adequately ventilated to avoid overheating.
Avoid contamination of thermistor surface during processing.
Operation
Use NTC inrush current limiters only within the specified operating temperature range.
Use NTC inrush current limiters only within the specified voltage and current ranges.
Environmental conditions must not harm the NTC inrush current limiters. Use NTC inrush current limiters
only in normal atmospheric conditions.
Contact of NTC inrush current limiters with any liquids and solvents should be prevented. It must be
ensured that no water enters the NTC inrush current limiters (e.g. through plug terminals). For
measurement purposes (checking the specified resistance vs. temperature), the component must not be
immersed in water but in suitable liquids (e.g. Galden).
In case of exposure of the NTC inrush current limiters to water, electrolytes or other aggressive media,
these media can penetrate the coating and reach the surface of the ceramic. Low-ohmic or high-ohmic
behavior may occur due to the formation of an electrolyte with metals (silver/lead/tin from metallization or
solder). Low-ohmic behavior is caused by electrochemical migration, high-ohmic behavior by dissolving of
the electrode. In either case, the functionality of the NTC inrush current limiters can not be assured.
Be sure to provide an appropriate fail-safe function to prevent secondary product damage caused by
malfunction (e.g. use a metal oxide varistor for limitation of overvoltage condition).
)
PPD VAR PD
Please read Cautions and warnings and
Important notes at the end of this document.
2017-07-31
Page 11 of 12
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As a
rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very high
level of operational safety and especially in customer applications in which the malfunction or
failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of the
customer application or other action taken by the customer (e.g. installation of protective circuitry
or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or
failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material
Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed
questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently,
we cannot guarantee that all products named in this publication will always be available.
The aforementioned does not apply in the case of individual agreements deviating from the
foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of
the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CTVS, DeltaCap,
DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD, MKK, MotorCap, PCC,
PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine, PQvar, SIFERRIT, SIFI,
SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, ThermoFuse, WindCap are
trademarks registered or pending in Europe and in other countries. Further information will be
found on the Internet at www.epcos.com/trademarks.
Page 12 of 12