B72214P2621K101

SIOV metal oxide varistors Leaded varistors, AdvanceD-MP, S14 compact series Series/Type: B72214P2*** Date: September 2019 © TDK Electronics AG 2019. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without TDK Electronics' prior express consent is prohibited. Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series Construction Round varistor element, leaded Coating: epoxy resin, flame-retardant to UL 94 V-0 Terminals: tinned wire Features High performance with smaller disk diameter Wide operating voltage range 130 ... 460 VRMS All types duty cycle @ 6 kV/ 3 kA = >10 pulses, according to IEC 62368-1; G.8.2 and IEC 60950-1; Annex Q, IEC 61051-2 All types In @ 3 kA = >15 impulses according to UL 1449, 4th edition surge current generator (8/20 µs), type 5 listed Multiple pulse handling capability Approvals UL CSA VDE IEC Delivery mode Bulk (standard), taped versions on reel or in Ammo pack upon request. For further details refer to chapter "Taping, packaging and lead configuration" for leaded varistors. General technical data Climatic category Operating temperature Storage temperature Electric strength Insulation resistance Please read Cautions and warnings and Important notes at the end of this document. to IEC 60068-1 to IEC 61051 to IEC 61051 to IEC 61051 Page 2 of 23 40/105/56 40 ... +105 40 ... +125 ≥ 2.5 ≥ 100 °C °C kVRMS MΩ Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series Electrical specifications and ordering codes Maximum ratings (TA = 105 °C) imax In 1) (8/20 µs) (8/20 µs) 1 time 15 times V V A A B72214P2131K102 S14K130E2K55 130 170 6000 3000 B72214P2141K102 S14K140E2K55 140 180 6000 3000 B72214P2151K102 S14K150E2K55 150 200 6000 3000 B72214P2171K102 S14K175E2K55 175 225 6000 3000 B72214P2211K102 S14K210E2K55 210 270 6000 3000 B72214P2231K103 S14K230E2K55 230 300 6000 3000 B72214P2251K103 S14K250E2K55 250 320 6000 3000 B72214P2271K104 S14K275E2K55 275 350 6000 3000 B72214P2301K103 S14K300E2K55 300 385 6000 3000 B72214P2321K102 S14K320E2K55 320 420 6000 3000 B72214P2351K103 S14K350E2K55 350 460 6000 3000 B72214P2381K102 S14K385E2K55 385 505 6000 3000 B72214P2421K104 S14K420E2K55 420 560 6000 3000 B72214P2461K102 S14K460E2K55 460 615 6000 3000 1) Note: Nominal discharge current In according to UL 1449, 4th edition. Ordering code Type (untaped) SIOV- Please read Cautions and warnings and Important notes at the end of this document. VRMS VDC Page 3 of 23 Wmax (2 ms) Pmax J W 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 60.0 65.0 70.0 80.0 95.0 105.0 115.0 130.0 140.0 150.0 165.0 180.0 190.0 200.0 Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series Characteristics (TA = 25 °C) Ordering code B72214P2131K102 B72214P2141K102 B72214P2151K102 B72214P2171K102 B72214P2211K102 B72214P2231K103 B72214P2251K103 B72214P2271K104 B72214P2301K103 B72214P2321K102 B72214P2351K103 B72214P2381K102 B72214P2421K104 B72214P2461K102 Type (untaped) SIOVS14K130E2K55 S14K140E2K55 S14K150E2K55 S14K175E2K55 S14K210E2K55 S14K230E2K55 S14K250E2K55 S14K275E2K55 S14K300E2K55 S14K320E2K55 S14K350E2K55 S14K385E2K55 S14K420E2K55 S14K460E2K55 Please read Cautions and warnings and Important notes at the end of this document. Vv (1 mA) V 205 220 240 270 330 360 390 430 470 510 560 620 680 750 ∆Vv (1 mA) % ±10 ±10 ±10 ±10 ±10 ±10 ±10 ±10 ±10 ±10 ±10 ±10 ±10 ±10 Page 4 of 23 vc,max (ic) V 340 360 395 455 545 595 650 710 775 840 910 1025 1120 1240 ic A 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 Ctyp (1 kHz) pF 790 720 645 575 495 450 420 380 350 320 295 280 255 230 Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series Dimensional drawings Weight Nominal diameter mm 14 VRMS Weight V g 130 ... 460 1.3 ... 5.0 The weight of varistors in between these voltage classes can be interpolated. Dimensions Ordering code B72214P2131K102 B72214P2141K102 B72214P2151K102 B72214P2171K102 B72214P2211K102 B72214P2231K103 B72214P2251K103 B72214P2271K104 B72214P2301K103 B72214P2321K102 B72214P2351K103 B72214P2381K102 B72214P2421K104 B72214P2461K102 [e] ±1 mm 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 Please read Cautions and warnings and Important notes at the end of this document. a (typical) mm 2.0 2.1 2.2 2.4 2.7 2.9 3.0 3.2 3.5 3.7 3.9 4.2 4.5 4.7 wmax mm 13.0 13.0 13.0 13.0 13.0 13.0 13.5 13.5 13.5 13.5 13.5 14.0 14.0 14.0 Page 5 of 23 thmax mm 4.7 4.8 4.9 5.1 5.4 5.6 5.7 5.9 6.1 6.3 6.7 7.7 8.2 8.5 hmax mm 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 18.0 18.0 18.0 lmin mm 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 d ±0.05 mm 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series Reliability data Test Test methods/conditions Requirement Varistor voltage The voltage between two terminals with To meet the specified value the specified measuring current applied is called VV (1 mADC @ 0.2 ... 2 s). Clamping voltage The maximum voltage between two terminals with the specified standard impulse current (8/20 µs) applied. To meet the specified value Endurance at upper category temperature 1000 h at UCT |∆V/V (1 mA)| ≤10% Surge current derating, 8/20 µs 10 surge currents (8/20 µs), unipolar, interval 30 s, amplitude corresponding to derating curve for 10 impulses at 20 µs Surge current derating, 2 ms 10 surge currents (2 ms), unipolar, |∆V/V (1 mA)| ≤10% interval 120 s, amplitude corresponding (measured in direction of to derating curve for 10 impulses at surge current) 2 ms No visible damage Electric strength IEC 61051-1, test 4.9.2 After having continuously applied the maximum allowable AC voltage at UCT ±2 °C for 1000 h, the specimen shall be stored at room temperature and normal humidity for 1 to 2 h. Thereafter, the change of VV shall be measured. Metal balls method, 2500 VRMS, 60 s The varistor is placed in a container holding 1.6 ±0.2 mm diameter metal balls such that only the terminations of the varistor are protruding. The specified voltage shall be applied between both terminals of the specimen connected together and the electrode inserted between the metal balls. Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 23 |∆V/V (1 mA)| ≤10% (measured in direction of surge current) No visible damage No breakdown Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series Test Test methods/conditions Requirement Climatic sequence The specimen shall be subjected to: a) dry heat at UCT, 16 h, IEC 60068-2-2, test Ba b) damp heat, 1st cycle: 55 °C, 93% r. H., 24 h, IEC 60068-2-30, test Db c) cold, LCT, 2 h, IEC 60068-2-1, test Aa d) damp heat, additional 5 cycles: 55 °C/25 °C, 93% r. H., 24 h/cycle, IEC 60068-2-30, test Db. |∆V/V (1 mA)| ≤10% Rins ≥100 MΩ Then the specimen shall be stored at room temperature and normal humidity for 1 to 2 h. Thereafter, the change of VV shall be measured. Thereafter, insulation resistance Rins shall be measured at V = 500 V. Rapid change of temperature IEC 60068-2-14, test Na, LCT/UCT, dwell time 30 min, 5 cycles |∆V/V (1 mA)| ≤5% No visible damage Damp heat, steady state IEC 60068-2-78, test Ca |∆V/V (1 mA)| ≤10% The specimen shall be subjected to Rins ≥100 MΩ 40 ±2 °C, 90 to 95% r. H. for 56 days without load / with 10% of the maximum continuous DC operating voltage VDC. Then stored at room temperature and normal humidity for 1 to 2 h. Thereafter, the change of VV shall be measured. Thereafter, insulation resistance Rins shall be measured at V = 500 V (insulated varistors only). Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 23 Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series Test Test methods/conditions Solderability IEC 60068-2-20, test Ta, Resistance to soldering heat IEC 60068-2-20, test Tb, method 1A, 260 °C, 10 s: Requirement The inspection shall be carried out under adequate method 1 with modified conditions for light with normal eyesight or lead-free solder alloys: 245 °C, 3 s: with the assistance of a After dipping the terminals to a depth of magnifier capable of giving approximately 3 mm from the body in a a magnification of 4 to soldering bath of 245 °C for 3 s, the 10 times. The dipped terminals shall be visually examined. surface shall be covered with a smooth and bright solder coating with no more than small amounts of scattered imperfections such as pinholes or un-wetted or de-wetted areas. These imperfections shall not be concentrated in one area. |∆V/V (1 mA)| ≤5% No visible damage Each lead shall be dipped into a solder bath having a temperature of 260 ±5 °C to a point 2.0 to 2.5 mm from the body of the specimen, be held there for 10 ±1 s and then be stored at room temperature and normal humidity for 1 to 2 h. The change of VV shall be measured and the specimen shall be visually examined. Tensile strength IEC 60068-2-21, test Ua1 |∆V/V (1 mA)| ≤5% After gradually applying the force specified below and keeping the unit fixed for 10 s, the terminal shall be visually examined for any damage. No break of solder joint, no wire break Force for wire diameter: 0.6 mm = 10 N 0.8 mm = 10 N 1.0 mm = 20 N Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 23 Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series Test Test methods/conditions Requirement Vibration IEC 60068-2-6, test Fc, method B4 Frequency range: 10 … 55 Hz Amplitude: 0.75 mm or 98 m/s2 Duration: 6 h (3 · 2 h) Pulse: sine wave After repeatedly applying a single harmonic vibration according to the table above. The change of VV shall be measured and the specimen shall be visually examined. |∆V/V (1 mA)| ≤5% IEC 60068-2-29, test Eb Pulse duration: 6 ms Max. acceleration: 400 m/s2 Number of bumps: 4000 Pulse: half sine IEC 60695-11-5 (needle flame test) |∆V/V (1 mA)| ≤5% Bump Fire hazard Severity: vertical 10 s Note: UCT = Upper category temperature LCT = Lower category temperature Rins = Insulation resistance Please read Cautions and warnings and Important notes at the end of this document. Page 9 of 23 No visible damage No visible damage 5 s max. Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series v/i characteristics v = f (i) - for explanation of the characteristics refer to "General technical information", 1.6.3 A = Leakage current, B = Protection level } for worst-case varistor tolerances SIOV-S14 ... E2K55 Please read Cautions and warnings and Important notes at the end of this document. Page 10 of 23 Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series Derating curves Maximum surge current imax = f (tr, pulse train) For explanation of the derating curves refer to "General technical information", section 1.8.1 SIOV-S14K130 ... K460E2K55 Please read Cautions and warnings and Important notes at the end of this document. Page 11 of 23 Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series Taping, packaging and lead configuration 1 EPCOS ordering code system For leaded varistors B722 or B723 10 S 2 271 K Monolithic varistor Nominal disc diameter Design: F = Fail-safe varistor Q = EnergetiQ S = Leaded varistor T = ThermoFuse U = Disk type, SNF X = Disk type, SNF (AEC-Q200) P = Disk type, AdvanceD-MP Series: 0 = StandarD 1 = Automotive 2 = AdvanceD 3 = SuperioR 4 = SuperioR Max. AC operating voltage: 271 = 27  101 = 275 VAC 140 = 14  100 = 14 VAC 141 = 14  101 = 140 VAC Tolerance of varistor voltage: K = ±10% J = ±5% S = Special tolerance Lead configuration: 1 = Straight leads 2 thru 9 = Kinked form Packaging: 0 = Bulk, 1 thru 7 = Taping style Internal coding: 1 = Standard Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 23 1 0 1 Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series 2 Taping and packaging of leaded varistors Tape packaging for lead spacing = 5 fully conforms to IEC 60286-2, while for lead spacings = 7.5 and 10 the taping mode is based on this standard. 2.1 Taping in accordance with IEC 60286-2 for lead spacing 5.0 mm 2.2 Taping based on IEC 60286-2 for lead spacing 7.5 and 10 mm Please read Cautions and warnings and Important notes at the end of this document. Page 13 of 23 Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series 2.3 Tape dimensions (in mm) Symbol w = 5.0 Tolerance th = 7.5 Tolerance = 10.0 Tolerance max. max. max. max. max. max. d P0 0.6 12.7 ±0.05 ±0.3 0.8 12.71) P1 F ∆h ∆p 3.85 5.0 0 0 ±0.7 +0.6/0.1 ±2.0 ±1.3 8.95 ±0.8 7.5 ±0.8 depends on s 0 ±2.0 W W0 18.0 5.5 ±0.5 min. 18.0 11.0 ±0.5 min. 18.0 11.0 ±0.5 min. W1 W2 H H0 9.0 3.0 18.0 16.0 (18.0) 32.2 4.0 0.9 11.0 0.5 ±0.5 max. +2.0/0 ±0.5 9.0 3.0 18.0 16.0 (18.0) 45.0 4.0 0.9 11.0 +0.75/0.5 max. +2.0/0 ±0.5 9.0 3.0 18.0 16.0 +0.75/0.5 max. +2.0/0 ±0.5 max. ±0.2 max. max. 45.0 4.0 0.9 11.0 max. ±0.2 max. max. H1 D0 t L L1 max. ±0.2 max. max. max. ±0.05 ±0.3 1.0 12.7 7.7 ±0.8 10.0 ±0.8 depends on s 0 ±2.0 1) Taping with P0 = 15.0 mm upon request 2) Applies only to uncrimped types 3) Applies only to crimped types (H0 = 18 upon request) Please read Cautions and warnings and Important notes at the end of this document. ±0.05 ±0.3 Page 14 of 23 Remarks see tables in each series under "Dimensions" ±1 mm/20 sprocket holes measured at top of component body Peel-off force > 5 N 2) 3) without lead Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series 2.4 Taping mode Example: B72210S0271K1 5 1 | Digit 14 Digit 14 Taping Reel type mode Seating plane height H0 for crimped types mm 0  Bulk  1 G I 16 2 G2 I 18 3 G3 II 16 4 G4 II 18 5 G5 III 16 6 GA Ammo pack 16 7 G2A Ammo pack 18 Internal coding for special taping G6 III 18 G10 II 16 G11 II 18 G10A Ammo pack 16 G11A Ammo pack 18 2.5 Seating plane height H for uncrimped types mm  18  18  18 18  Pitch distance P0 mm  12.7 12.7 12.7 12.7 12.7 12.7 12.7  18  18  12.7 15.0 15.0 15.0 15.0 Reel dimension Dimensions (in mm) Reel type I II III d 360 max. 360 max. 500 max. f 31 ±1 31 ±1 23 ±1 n approx. 45 approx. 55 approx. 59 w 54 max. 64 max. 72 max. If reel type III is not compatible with insertion equipment because of its large diameter, nominal disk diameter 10 mm and 14 mm can be supplied on reel II upon request (taping mode G3). Please read Cautions and warnings and Important notes at the end of this document. Page 15 of 23 Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series 2.6 Ammo pack dimensions 3 Lead configuration Straight leads are standard for disk varistors. Other lead configurations as crimp style or customer-specific lead wire length according to 3.1, 3.2, 3.3 and 3.4 are optional. Crimped leads (non-standard) are differently crimped for technical reasons; the individual crimp styles are denoted by consecutive numbers (S, S2 through S5) as shown in the dimensional drawings below. The crimp styles of the individual types can be seen from the type designation in the ordering tables. 3.1 Crimp style mode Example: B72210S0271K 5 01 | Digit 13 Digit 13 of ordering code Crimp style Figure 1 Standard, straight leads 1 2 S2 2 3 S3 3 5 S5 4 Please read Cautions and warnings and Important notes at the end of this document. Page 16 of 23 Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series 3.2 Standard leads and non-standard crimp styles The basic dimensions in figure 1 to 5 are valid for types with either round or square (EnergetiQ series) component head. Standard, straight leads Non-standard, crimp style S2 Non-standard, crimp style S3 Figure 1 Figure 2 Figure 3 Non-standard, crimp style S5 Figure 4 Please read Cautions and warnings and Important notes at the end of this document. Page 17 of 23 Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series 3.3 Trimmed leads (non-standard) Varistors with cut leads available upon request. Lead length tolerances: Straight leads Crimped leads Minimum lead length +/0.8 mm +/0.5 mm 3.0 mm Please read Cautions and warnings and Important notes at the end of this document. Page 18 of 23 Leaded varistors B72214P2*** AdvanceD-MP, S14 compact series Cautions and warnings General 1. EPCOS metal oxide varistors are designed for specific applications and should not be used for purposes not identified in our specifications, application notes and data books unless otherwise agreed with EPCOS during the design-in-phase. 2. Ensure suitability of SIOVs through reliability testing during the design-in phase. SIOVs should be evaluated taking into consideration worst-case conditions. 3. For applications of SIOVs in line-to-ground circuits based on various international and local standards there are restrictions existing or additional safety measures required. Storage 1. Store SIOVs only in original packaging. Do not open the package prior to processing. 2. Recommended storage conditions in original packaging: Storage temperature: 25 °C ... +45 °C, Relative humidity: