B82614R2202A030

Power line chokes Sine-wave chokes 0.8 ... 2.7 A, 0.5 ... 3.0 mH, +40 °C Series/Type: Ordering code: B82614 Date: February 2023  TDK Electronics AG 2023. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without TDK Electronics’ prior express consent is prohibited. Power line chokes Sine-wave chokes B82614 Rated voltage 250 V AC Rated current 0.8 ... 2.7 A Nominal inductance 0.5 ... 3.0 mH Construction      Single choke Air-gapped rectangular ferrite core Closed plastic coil former (UL 94 V-0)1) Without encapsulation 4-section winding Features       High resonance frequency due to 4-section winding Low saturation effects due to gapped core Suitable for wave soldering Design complies with EN 60938-2 (VDE 0565-2) Recyclable owing to omission of encapsulation and glue RoHS-compatible Applications     Suppression of differential-mode interferences Switch-mode applications Reduction of harmonics and PFC SMPS featuring a current pump circuit Terminals      Base material CuNi18Zn20 Layer composition Ni, Sn Hot-dipped Pins 0.7  0.7 (mm) Lead spacing 12.5  15 (mm) Marking  Product brand (EPCOS), ordering code, rated inductance, rated current, rated voltage, date of manufacture (WWYY) Delivery mode  Blister tray in cardbox 1) Additionally certified values: Glow wire flammability index (GWFI to IEC 60695-2-12): Glow wire ignition temperature (GWIT to IEC 60695-2-13): Comparative tracking index (CTI to IEC 60112): Ball pressure test (BP to IEC 60695-10-2): Please read Cautions and warnings and Important notes at the end of this document. 2 +850 °C +775 °C 175 V +125 °C 2/23 Power line chokes Sine-wave chokes B82614 Dimensional drawing and pin configuration Circuit diagram Please read Cautions and warnings and Important notes at the end of this document. 3 2/23 Power line chokes Sine-wave chokes B82614 Technical data and measuring conditions Rated voltage VR 250 V AC (50/60 Hz) Rated temperature TR +40 C Rated current IR Referred to 50 Hz and rated temperature Nominal inductance LN Defined at zero DC current bias Measured with Agilent 4284A at 0.1 mA, +20 C Measuring frequency: LR 1 mH = 100 kHz LR > 1 mH = 10 kHz Inductance tolerance 30% at +20 C Inductance at rated current Measured at DC magnetic bias with IR with Agilent 4284A at 0.1 mA, +20 C, typical values Measuring frequency: LR 1 mH = 100 kHz LR > 1 mH = 10 kHz DC resistance Rtyp Measured at +20 C, typical values Solderability (lead free) Sn96.5Ag3.0Cu0.5: +(245 5) °C, (3 0.3) s Wetting of soldering area 95% (to IEC 60068-2-20, test Ta) Resistance to soldering heat (wave soldering) +(260 5) °C, (10 1) s (to IEC 60068-2-20, test Tb) Climatic category 40/125/56 (to IEC 60068-1) Storage conditions (packaged) –25 °C … +40 °C, 75% RH Weight Approx. 30 g Characteristics and ordering codes IR A LN mH L at IR, typ. mH Rtyp  Ordering code 0.8 1.0 1.7 2.0 2.4 2.7 3.0 2.0 1.5 1.0 0.75 0.5 2.9 1.9 0.95 0.75 0.50 0.42 1.9 1.3 0.61 0.43 0.33 0.23 B82614R2801A030 B82614R2102A030 B82614R2172A030 B82614R2202A030 B82614R2242A030 B82614R2272A030 Please read Cautions and warnings and Important notes at the end of this document. 4 2/23 Power line chokes Sine-wave chokes B82614 Impedance |Z| versus frequency f measured at +20 °C, typical values IND0866-L 10 6 W Relative inductance Lop/LR versus relative current Iop/IR measured at +20 °C, typical values B82614 IND0868-C 110 B82614 L op % LR |Z | 90 10 5 R2801A030 R2102A030 R2172A030 R2202A030 R2242A030 R2272A030 80 70 10 4 60 10 3 10 2 5 10 50 R2801A030 R2102A030 R2172A030 R2202A030 R2242A030 R2272A030 40 30 20 10 6 Hz 10 7 f 0 Current derating Iop/IR versus ambient temperature TA Please read Cautions and warnings and Important notes at the end of this document. 5 2/23 0.2 0.4 0.6 0.8 1 I op IR 1.2 Power line chokes Sine-wave chokes B82614 Cautions and warnings  Please note the recommendations in our Inductors data book (latest edition) and in the data sheets. – Particular attention should be paid to the derating curves given there. – The soldering conditions should also be observed. Temperatures quoted in relation to wave soldering refer to the pin, not the housing.  If the components are to be washed varnished it is necessary to check whether the washing varnish agent that is used has a negative effect on the wire insulation, any plastics that are used, or on glued joints. In particular, it is possible for washing varnish agent residues to have a negative effect in the long-term on wire insulation. Washing processes may damage the product due to the possible static or cyclic mechanical loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts, which might lead to reduced reliability or lifetime.  The following points must be observed if the components are potted in customer applications: – Many potting materials shrink as they harden. They therefore exert a pressure on the plastic housing or core. This pressure can have a deleterious effect on electrical properties, and in extreme cases can damage the core or plastic housing mechanically. – It is necessary to check whether the potting material used attacks or destroys the wire, wire insulation, plastics or glue. – The effect of the potting material can change the high-frequency behaviour of the components. – Many coating materials have a negative effect (chemically and mechanically) on the winding wires, insulation materials and connecting points. Customers are always obligated to determine whether and to what extent their coating materials influence the component. Customers are responsible and bear all risk for the use of the coating material. TDK Electronics does not assume any liability for failures of our components that are caused by the coating material.  Ceramics / ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to breakage of the core.  Even for customer-specific products, conclusive validation of the component in the circuit can only be carried out by the customer. Display of ordering codes for TDK Electronics products The ordering code for one and the same product can be represented differently in data sheets, data books, other publications, on the company website, or in order-related documents such as shipping notes, order confirmations and product labels. The varying representations of the ordering codes are due to different processes employed and do not affect the specifications of the respective products. Detailed information can be found on the Internet under www.tdk-electronics.tdk.com/orderingcodes. Please read Cautions and warnings and Important notes at the end of this document. 6 2/23 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, we are either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether a product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.tdk-electronics.tdk.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to our General Terms and Conditions of Supply. 7 2/23 Important notes 7. Our manufacturing sites serving the automotive business apply the IATF 16949 standard. The IATF certifications confirm our compliance with requirements regarding the quality management system in the automotive industry. Referring to customer requirements and customer specific requirements (“CSR”) TDK always has and will continue to have the policy of respecting individual agreements. Even if IATF 16949 may appear to support the acceptance of unilateral requirements, we hereby like to emphasize that only requirements mutually agreed upon can and will be implemented in our Quality Management System. For clarification purposes we like to point out that obligations from IATF 16949 shall only become legally binding if individually agreed upon. 8. The trade names EPCOS, CarXield, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CTVS, DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, InsuGate, LeaXield, MiniBlue, MiniCell, MKD, MKK, ModCap, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine, PQvar, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, ThermoFuse, WindCap, XieldCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.tdk-electronics.tdk.com/trademarks. Release 2022-07 8 2/23