MLF1608A2R2KTA00

I N D U C T O R S February 2017 Inductors for Standard Circuits Multilayer Ferrite MLF Series MLF1608 Type MLF1608 1608 [0603 inch]* * Dimensions Code JIS[EIA] (2/11) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20170205 / inductor_commercial_standard_mlf1608_en.fm (3/11) I N D U C T O R S Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Inductors for Standard Circuits Multilayer Ferrite Overview of MLF1608 Type FEATURES The lineup includes a wide inductance range. Highly reliable monolithic structure with multilayer integration. APPLICATION Smart phones, tablet terminals, tuners, LCD-TVs, PDP-TVs, audio equipment, computers, signal processing for modules etc. PART NUMBER CONSTRUCTION MLF Series name 1608 L×W×H Dimensions (mm) 1608 1.6×0.8×0.8 D characteristics A C D E 47N △ Inductance (µH) 0.010 10N (10nH) R10 0.1 1R0 1 Inductance tolerance J ±5% K ±10% M ±20% T 000 Packaging style Internal code T Taping 000 A00 D00 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Package quantity Individual weight Operating Storage Type temperature temperature (pieces/reel) （°C） （°C） （mg） MLF1608 –55 to +125 –55 to +125 4,000 4 In case the product's inductance is 15µH or higher, both Operating and Storage temperature ranges are –40 to +85°C. The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170205 / inductor_commercial_standard_mlf1608_en.fm (4/11) I N D U C T O R S MLF1608 Type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 30 to 60s Peak Temp. Time T4 t3 250 to 260°C 10s max. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170205 / inductor_commercial_standard_mlf1608_en.fm (5/11) I N D U C T O R S MLF1608 Type 0.80±0.15 SHAPE & DIMENSIONS 0.30±0.20 0.30±0.20 0.80±0.15 1.60±0.15 Dimensions in mm 0.8 RECOMMENDED LAND PATTERN 0.6 0.8 0.6 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170205 / inductor_commercial_standard_mlf1608_en.fm (6/11) I N D U C T O R S MLF1608 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L Q (µH) 0.047 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 Tolerance ±20% ±20% ±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±5%±10%±20% ±10%±20% ±10%±20% ±10%±20% ±10%±20% ±10%±20% min. 10 10 10 15 15 15 15 15 15 15 15 15 15 15 15 35 35 35 35 35 35 35 35 35 35 35 35 30 30 20 20 20 20 20 L, Q measuring conditions typ. 20 20 20 25 25 25 25 25 25 25 25 30 30 30 30 50 50 55 55 55 55 60 60 60 60 60 60 55 55 40 40 40 40 40 Frequency Current (MHz) 50 50 50 25 25 25 25 25 25 25 25 25 25 25 25 10 10 10 10 10 10 10 10 10 4 4 4 2 2 1 1 1 1 1 (mA) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 Self-resonant frequency DC resistance Rated current (MHz)min. 600 550 500 450 400 350 320 290 260 230 210 190 170 150 130 120 110 100 90 80 70 65 60 55 45 40 35 30 25 22 20 18 15 10 (Ω )max. 0.20 0.30 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.75 0.85 0.95 1.05 1.25 1.40 0.50 0.65 0.70 0.85 1.00 1.15 1.30 1.45 1.60 1.10 1.30 1.50 1.70 1.80 1.50 1.60 1.70 1.80 2.20 (mA)max. 200 200 200 200 200 200 150 150 150 100 100 100 100 70 70 50 50 50 50 30 30 30 30 30 15 15 10 10 10 2 2 2 2 2 (MHz)typ. 900 700 650 600 550 500 450 400 350 320 290 260 230 210 190 170 150 140 130 120 110 100 90 80 70 60 55 50 45 42 40 38 35 30 (Ω )typ. 0.10 0.15 0.15 0.20 0.20 0.25 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.65 0.75 0.25 0.25 0.30 0.35 0.45 0.50 0.55 0.65 0.75 0.55 0.65 0.80 1.00 1.20 0.80 0.85 0.90 1.20 1.40 Part No. MLF1608D47N△T□□□ MLF1608D68N△T□□□ MLF1608D82N△T□□□ MLF1608DR10 △ T □□□ MLF1608DR12 △ T □□□ MLF1608DR15 △ T □□□ MLF1608DR18 △ T □□□ MLF1608DR22 △ T □□□ MLF1608DR27 △ T □□□ MLF1608DR33 △ T □□□ MLF1608DR39 △ T □□□ MLF1608DR47 △ T □□□ MLF1608DR56 △ T □□□ MLF1608DR68 △ T □□□ MLF1608DR82 △ T □□□ MLF1608A1R0 △ T □□□ MLF1608A1R2 △ T □□□ MLF1608A1R5 △ T □□□ MLF1608A1R8 △ T □□□ MLF1608A2R2 △ T □□□ MLF1608A2R7 △ T □□□ MLF1608A3R3 △ T □□□ MLF1608A3R9 △ T □□□ MLF1608A4R7 △ T □□□ MLF1608E5R6 △ T □□□ MLF1608E6R8 △ T □□□ MLF1608E8R2 △ T □□□ MLF1608E100 △ T □□□ MLF1608E120 △ T □□□ MLF1608C150 △ T □□□ MLF1608C180 △ T □□□ MLF1608C220 △ T □□□ MLF1608C270 △ T □□□ MLF1608C330 △ T □□□  The " △ " of the Part Number contains the inductance tolerance code, J (±5%), K (±10%), or M (±20%).  The " □ " of the Part Number contains the internal code (000, A00, or D00), following below. • In case the inductance tolerance code is J: 000 • In case the inductance tolerance code is M or K (L = 0.047 to 8.2µH or 15 to 22µH): A00 • In case the inductance tolerance code is M or K (L = 10,12,27,33µ): D00 ○ Measurement equipment Measurement item Product No. L, Q 4294A+16034G Self-resonant frequency E4991A DC resistance Type-7561 ＊ Equivalent measurement equipment may be used. Manufacturer Keysight Technologies Keysight Technologies Yokogawa Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170205 / inductor_commercial_standard_mlf1608_en.fm (7/11) I N D U C T O R S MLF1608 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 E6R8 10 E100 Inductance(µH) A4R7 A3R3 A1R0 1 A2R2 A1R5 DR68 DR47 DR33 DR22 DR15 0.1 DR10 0.01 1 10 100 1000 Frequency(MHz) 100 E120 10 E5R6 E8R2 Inductance(µH) A3R9 A2R7 A1R2 1 A1R8 DR82 DR56 DR39 DR27 DR18 0.1 DR12 0.01 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Keysight Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170205 / inductor_commercial_standard_mlf1608_en.fm (8/11) I N D U C T O R S MLF1608 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 C330 C270 Inductance(µH) 10 C220 C180 C150 1 0.1 0.1 1 10 100 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer 4294A+16034G Keysight Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170205 / inductor_commercial_standard_mlf1608_en.fm (9/11) I N D U C T O R S MLF1608 Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 70 A3R3 60 A1R0 A1R5 A2R2 50 DR47 40 DR15 Q DR22 DR33 E6R8 E100 30 DR10 20 DR68 10 0 1 10 100 1000 Frequency(MHz) 70 60 A3R9 A1R2 E8R2 50 E5R6 Q 40 E120 30 A1R8 A2R7 DR12 DR82 DR56 DR18 20 DR39 10 0 DR27 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Keysight Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170205 / inductor_commercial_standard_mlf1608_en.fm (10/11) I N D U C T O R S MLF1608 Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 70 60 50 C150 C330 40 Q C270 30 C180 C220 20 10 0 0.1 1 10 100 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer 4294A+16034G Keysight Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170205 / inductor_commercial_standard_mlf1608_en.fm (11/11) I N D U C T O R S MLF1608 Type PACKAGING STYLE REEL DIMENSIONS ø60min. 1.0 2.0±0.5 8.4 +2.0 –0.0 ø13±0.2 14.4max. ø21±0.8 ø180±2.0 Dimensions in mm Cavity 3.5±0.05 1.5 +0.1 –0.0 Type MLF1608 A 1.9±0.2 B 1.1±0.2 K 1.1 max. A 8.0±0.3 Sprocket hole 1.75±0.1 TAPE DIMENSIONS K B 4.0±0.1 2.0±0.05 160min. Drawing direction Taping 2.0±0.05 200min. 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170205 / inductor_commercial_standard_mlf1608_en.fm