MLG1608SR27JTD25

I N D U C T O R S December 2015 Inductors for High Frequency Circuits Multilayer Ceramic MLG Series (For automobiles) MLG1608 Type MLG1608 1608 [0603 inch]* * Dimensions Code JIS[EIA] Caution The products in this catalog will be or have been stopped production Discontinue Issue Date Nov.4, 2015 Last Purchase Order Date Dec.29, 2016 Last Shipment Date Jan.30, 2017 Please refer to our Web site about replacement information. (2/12) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. pr od u st cts op w pe il d lb pr e od or uc ha tio ve n be en SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. Th e (1) Aerospace/Aviation equipment (2) Transportation equipment (electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20151217 / inductor_automotive_high-frequency_mlg1608_en.fm (3/12) I N D U C T O R S Inductors for High Frequency Circuits Product compatible with RoHS directive Halogen-free Compatible with lead-free solders AEC-Q200 Multilayer Ceramic pr od u st cts op w pe il d lb pr e od or uc ha tio ve n be en Overview of MLG1608 Type FEATURES Advanced monolithic structure is formed using a multilayering and sintering process with ceramic and conductive materials for Highfrequency. APPLICATION Automotive equipment, smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners and other high frequency circuits for the mobile communication industry PART NUMBER CONSTRUCTION MLG Series name 1608 B L×W×H Dimensions (mm) 1608 1.6×0.8×0.8 Product internal code B S 1N0 S Inductance (nH) 1N0 1.0 10N 10 R10 100 1R0 1000 Inductance tolerance S ±0.3nH D ±0.5nH J ±5% T D25 Packaging style Internal code T Taping D25 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Individual weight （mg） 4 Th e Temperature range Package quantity Operating Storage Type temperature temperature (pieces/reel) （°C） （°C） MLG1608 –55 to +125 –55 to +125 4000 The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151217 / inductor_automotive_high-frequency_mlg1608_en.fm (4/12) I N D U C T O R S MLG1608 Type RECOMMENDED REFLOW PROFILE Soldering Natural cooling pr od u st cts op w pe il d lb pr e od or uc ha tio ve n be en Preheating Peak T: Temperature T4 T3 T2 T1 t1 T3 t3 t2 t: Time Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 30 to 60s Peak Temp. T4 250 to 260°C Time t3 10s max. Th e Preheating Temp. T1 T2 150°C 180°C Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151217 / inductor_automotive_high-frequency_mlg1608_en.fm (5/12) I N D U C T O R S MLG1608 Type 0.30±0.20 pr od u st cts op w pe il d lb pr e od or uc ha tio ve n be en 0.80±0.15 SHAPE & DIMENSIONS 0.30±0.20 0.80±0.15 1.60±0.15 Dimensions in mm 0.8 RECOMMENDED LAND PATTERN 0.8 0.6 Dimensions in mm Th e 0.6 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151217 / inductor_automotive_high-frequency_mlg1608_en.fm (6/12) I N D U C T O R S MLG1608 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE (nH) 1 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 Q L, Q measuring frequency Self-resonant frequency DC resistance Rated current Part No. min. 8 8 8 8 10 10 10 10 10 10 10 10 12 12 12 12 12 12 12 12 14 14 14 14 14 14 14 14 14 14 10 10 10 10 10 10 10 (MHz) 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 50 50 50 50 50 50 50 (GHz)min. 10.0 10.0 10.0 10.0 8.0 7.0 6.5 6.0 5.0 5.0 4.5 4.5 3.5 3.0 2.8 2.6 2.3 2.0 1.8 1.6 1.4 1.2 1.1 1.0 0.80 0.65 0.55 0.50 0.45 0.35 0.35 0.30 0.25 0.25 0.20 0.15 0.13 (: )max. 0.10 0.10 0.10 0.10 0.10 0.12 0.12 0.14 0.15 0.16 0.18 0.20 0.20 0.25 0.28 0.32 0.35 0.40 0.50 0.55 0.60 0.70 0.75 0.80 1.00 1.20 1.30 1.40 1.70 2.00 2.80 3.00 3.50 4.50 5.50 5.50 5.50 (mA)max. 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 500 500 500 400 400 400 300 300 300 300 250 250 200 200 100 100 100 70 70 70 70 MLG1608B1N0STD25 MLG1608B1N2STD25 MLG1608B1N5STD25 MLG1608B1N8STD25 MLG1608B2N2STD25 MLG1608B2N7STD25 MLG1608B3N3STD25 MLG1608B3N9STD25 MLG1608B4N7STD25 MLG1608B5N6DTD25 MLG1608B6N8DTD25 MLG1608B8N2DTD25 MLG1608B10NJTD25 MLG1608B12NJTD25 MLG1608B15NJTD25 MLG1608B18NJTD25 MLG1608B22NJTD25 MLG1608B27NJTD25 MLG1608B33NJTD25 MLG1608B39NJTD25 MLG1608B47NJTD25 MLG1608B56NJTD25 MLG1608B68NJTD25 MLG1608B82NJTD25 MLG1608BR10JTD25 MLG1608SR12JTD25 MLG1608SR15JTD25 MLG1608SR18JTD25 MLG1608SR22JTD25 MLG1608SR27JTD25 MLG1608SR33JTD25 MLG1608SR39JTD25 MLG1608SR47JTD25 MLG1608SR56JTD25 MLG1608SR68JTD25 MLG1608SR82JTD25 MLG1608S1R0JTD25 pr od u st cts op w pe il d lb pr e od or uc ha tio ve n be en L Tolerance ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.5nH ±0.5nH ±0.5nH ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% (GHz)typ. 20up 20up 19.6 16.6 10.8 8.8 8.8 7.9 6.8 6.8 5.7 5.6 4.5 3.8 3.6 3.3 3.0 2.7 2.3 2.0 1.8 1.8 1.6 1.4 1.2 0.8 0.7 0.6 0.6 0.5 0.5 0.4 0.4 0.4 0.3 0.2 0.2 (: )typ. 0.03 0.04 0.03 0.04 0.05 0.06 0.06 0.06 0.08 0.08 0.10 0.10 0.11 0.13 0.14 0.16 0.19 0.21 0.25 0.26 0.35 0.41 0.43 0.50 0.64 0.89 1.03 1.08 1.29 1.59 1.90 2.06 2.47 3.20 3.88 3.76 4.27 Please contact us for ±2% inductance tolerance (code G) products. Manufacturer Agilent Technologies Panasonic Yokogawa Th e ○ Measurement equipment Measurement item Product No. L, Q 4291B +16193A Self-resonant frequency 8720C DC resistance Type-7561 ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151217 / inductor_automotive_high-frequency_mlg1608_en.fm (7/12) I N D U C T O R S MLG1608 Type ELECTRICAL CHARACTERISTICS L, Q FREQUENCY CHARACTERISTICS TABLE 500MHz 1.0 1.2 1.5 1.8 2.2 2.6 3.2 3.8 4.6 5.4 6.6 8.0 9.8 11.8 14.8 17.8 21.9 27.1 33.4 40.2 49.1 59.6 74.0 91.1 118 188 Part No.* Q typ. pr od u st cts op w pe il d lb pr e od or uc ha tio ve n be en L(nH)typ. 800MHz 1.0 1.1 1.5 1.8 2.1 2.6 3.2 3.8 4.6 5.5 6.7 8.1 10.0 12.1 15.4 18.5 22.9 28.8 36.0 45.0 56.0 71.1 92.8 120.6 1.8GHz 1.0 1.2 1.5 1.8 2.2 2.7 3.3 4.0 4.9 5.8 7.3 8.9 11.5 14.8 20.6 25.5 33.6 50.6 2.0GHz 1.0 1.2 1.5 1.8 2.2 2.7 3.3 4.0 5.0 5.9 7.5 9.3 12.1 16.0 23.4 29.3 40.2 2.4GHz 1.0 1.2 1.5 1.8 2.2 2.8 3.4 4.1 5.2 6.2 8.0 10 13.6 19.3 500MHz 39 28 37 38 44 40 38 40 41 37 38 39 38 39 38 36 36 37 37 36 38 37 34 33 35 23 800MHz 48 35 48 48 54 51 48 50 51 46 47 48 47 48 46 44 44 43 43 40 41 38 33 31 1.8GHz 77 57 78 77 88 79 76 79 76 69 67 67 63 59 49 47 43 34 2.0GHz 82 60 81 81 91 81 79 81 79 71 68 68 63 57 46 42 38 2.4GHz 95 68 93 95 107 94 91 93 88 79 74 71 61 51 MLG1608B1N0STD25 MLG1608B1N2STD25 MLG1608B1N5STD25 MLG1608B1N8STD25 MLG1608B2N2STD25 MLG1608B2N7STD25 MLG1608B3N3STD25 MLG1608B3N9STD25 MLG1608B4N7STD25 MLG1608B5N6DTD25 MLG1608B6N8DTD25 MLG1608B8N2DTD25 MLG1608B10NJTD25 MLG1608B12NJTD25 MLG1608B15NJTD25 MLG1608B18NJTD25 MLG1608B22NJTD25 MLG1608B27NJTD25 MLG1608B33NJTD25 MLG1608B39NJTD25 MLG1608B47NJTD25 MLG1608B56NJTD25 MLG1608B68NJTD25 MLG1608B82NJTD25 MLG1608BR10JTD25 MLG1608SR12JTD25 MLG1608SR15JTD25 MLG1608SR18JTD25 MLG1608SR22JTD25 MLG1608SR27JTD25 MLG1608SR33JTD25 MLG1608SR39JTD25 MLG1608SR47JTD25 MLG1608SR56JTD25 MLG1608SR68JTD25 MLG1608SR82JTD25 MLG1608S1R0JTD25 Please contact us for ±2% inductance tolerance (code G) products. Th e ○ Measurement equipment Product No. Manufacturer 4291B +16193A Agilent Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151217 / inductor_automotive_high-frequency_mlg1608_en.fm (8/12) I N D U C T O R S MLG1608 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE (nH) 1 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 Q L, Q measuring frequency Self-resonant frequency DC resistance Rated current Part No. min. 8 8 8 8 10 10 10 10 10 10 10 10 12 12 12 12 12 12 12 12 14 14 14 14 14 14 14 14 14 14 10 10 10 10 10 10 10 (MHz) 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 50 50 50 50 50 50 50 (GHz)min. 10.0 10.0 10.0 10.0 8.0 7.0 6.5 6.0 5.0 5.0 4.5 4.5 3.5 3.0 2.8 2.6 2.3 2.0 1.8 1.6 1.4 1.2 1.1 1.0 0.80 0.65 0.55 0.50 0.45 0.35 0.35 0.30 0.25 0.25 0.20 0.15 0.13 (: )max. 0.10 0.10 0.10 0.10 0.10 0.12 0.12 0.14 0.15 0.16 0.18 0.20 0.20 0.25 0.28 0.32 0.35 0.40 0.50 0.55 0.60 0.70 0.75 0.80 1.00 1.20 1.30 1.40 1.70 2.00 2.80 3.00 3.50 4.50 5.50 5.50 5.50 (mA)max. 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 500 500 500 400 400 400 300 300 300 300 250 250 200 200 100 100 100 70 70 70 70 MLG1608B1N0STD25 MLG1608B1N2STD25 MLG1608B1N5STD25 MLG1608B1N8STD25 MLG1608B2N2STD25 MLG1608B2N7STD25 MLG1608B3N3STD25 MLG1608B3N9STD25 MLG1608B4N7STD25 MLG1608B5N6DTD25 MLG1608B6N8DTD25 MLG1608B8N2DTD25 MLG1608B10NJTD25 MLG1608B12NJTD25 MLG1608B15NJTD25 MLG1608B18NJTD25 MLG1608B22NJTD25 MLG1608B27NJTD25 MLG1608B33NJTD25 MLG1608B39NJTD25 MLG1608B47NJTD25 MLG1608B56NJTD25 MLG1608B68NJTD25 MLG1608B82NJTD25 MLG1608BR10JTD25 MLG1608SR12JTD25 MLG1608SR15JTD25 MLG1608SR18JTD25 MLG1608SR22JTD25 MLG1608SR27JTD25 MLG1608SR33JTD25 MLG1608SR39JTD25 MLG1608SR47JTD25 MLG1608SR56JTD25 MLG1608SR68JTD25 MLG1608SR82JTD25 MLG1608S1R0JTD25 pr od u st cts op w pe il d lb pr e od or uc ha tio ve n be en L Tolerance ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.5nH ±0.5nH ±0.5nH ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% (GHz)typ. 20up 20up 19.6 16.6 10.8 8.8 8.8 7.9 6.8 6.8 5.7 5.6 4.5 3.8 3.6 3.3 3.0 2.7 2.3 2.0 1.8 1.8 1.6 1.4 1.2 0.8 0.7 0.6 0.6 0.5 0.47 0.43 0.39 0.36 0.31 0.22 0.19 (: )typ. 0.03 0.04 0.03 0.04 0.05 0.06 0.06 0.06 0.08 0.08 0.10 0.10 0.11 0.13 0.14 0.16 0.19 0.21 0.25 0.26 0.35 0.41 0.43 0.50 0.64 0.89 1.03 1.08 1.29 1.59 1.90 2.06 2.47 3.20 3.88 3.76 4.27 Please contact us for ±2% inductance tolerance (code G) products. Manufacturer Agilent Technologies Panasonic Yokogawa Th e ○ Measurement equipment Measurement item Product No. L, Q 4291B +16193A Self-resonant frequency 8720C DC resistance Type-7561 ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151217 / inductor_automotive_high-frequency_mlg1608_en.fm (9/12) I N D U C T O R S MLG1608 Type ELECTRICAL CHARACTERISTICS L, Q FREQUENCY CHARACTERISTICS TABLE 500MHz 1.0 1.2 1.5 1.8 2.2 2.6 3.2 3.8 4.6 5.4 6.6 8.0 9.8 11.8 14.8 17.8 21.9 27.1 33.4 40.2 49.1 59.6 74.0 91.1 118 188 Part No.* Q typ. pr od u st cts op w pe il d lb pr e od or uc ha tio ve n be en L(nH)typ. 800MHz 1.0 1.1 1.5 1.8 2.1 2.6 3.2 3.8 4.6 5.5 6.7 8.1 10.0 12.1 15.4 18.5 22.9 28.8 36.0 45.0 56.0 71.1 92.8 120.6 1.8GHz 1.0 1.2 1.5 1.8 2.2 2.7 3.3 4.0 4.9 5.8 7.3 8.9 11.5 14.8 20.6 25.5 33.6 50.6 2.0GHz 1.0 1.2 1.5 1.8 2.2 2.7 3.3 4.0 5.0 5.9 7.5 9.3 12.1 16.0 23.4 29.3 40.2 2.4GHz 1.0 1.2 1.5 1.8 2.2 2.8 3.4 4.1 5.2 6.2 8.0 10 13.6 19.3 500MHz 39 28 37 38 44 40 38 40 41 37 38 39 38 39 38 36 36 37 37 36 38 37 34 33 35 23 800MHz 48 35 48 48 54 51 48 50 51 46 47 48 47 48 46 44 44 43 43 40 41 38 33 31 1.8GHz 77 57 78 77 88 79 76 79 76 69 67 67 63 59 49 47 43 34 2.0GHz 82 60 81 81 91 81 79 81 79 71 68 68 63 57 46 42 38 2.4GHz 95 68 93 95 107 94 91 93 88 79 74 71 61 51 MLG1608B1N0STD25 MLG1608B1N2STD25 MLG1608B1N5STD25 MLG1608B1N8STD25 MLG1608B2N2STD25 MLG1608B2N7STD25 MLG1608B3N3STD25 MLG1608B3N9STD25 MLG1608B4N7STD25 MLG1608B5N6DTD25 MLG1608B6N8DTD25 MLG1608B8N2DTD25 MLG1608B10NJTD25 MLG1608B12NJTD25 MLG1608B15NJTD25 MLG1608B18NJTD25 MLG1608B22NJTD25 MLG1608B27NJTD25 MLG1608B33NJTD25 MLG1608B39NJTD25 MLG1608B47NJTD25 MLG1608B56NJTD25 MLG1608B68NJTD25 MLG1608B82NJTD25 MLG1608BR10JTD25 MLG1608SR12JTD25 MLG1608SR15JTD25 MLG1608SR18JTD25 MLG1608SR22JTD25 MLG1608SR27JTD25 MLG1608SR33JTD25 MLG1608SR39JTD25 MLG1608SR47JTD25 MLG1608SR56JTD25 MLG1608SR68JTD25 MLG1608SR82JTD25 MLG1608S1R0JTD25 Please contact us for ±2% inductance tolerance (code G) products. Th e ○ Measurement equipment Product No. Manufacturer 4291B +16193A Agilent Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151217 / inductor_automotive_high-frequency_mlg1608_en.fm (10/12) I N D U C T O R S MLG1608 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE) 10000 R68 R56 1R0 R82 R47 R39 R33 R27 R22 R18 R15 R12 1000 R10 82N 56N 68N 47N 39N 22N 33N 27N 100 18N Inductance(nH) 15N 12N 10N 8N2 10 6N8 5N6 4N7 3N9 3N3 2N7 2N2 1N8 1N5 1N2 1N0 1 0 10 100 1000 10000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A +16193A Agilent Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151217 / inductor_automotive_high-frequency_mlg1608_en.fm (11/12) I N D U C T O R S MLG1608 Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE) 100 1N5 2N7 3N3 3N9 2N2 4N7 1N8 90 5N6 6N8 80 1N2 1N0 70 8N2 Q 60 50 10N 27N 33N 40 39N 68N 56N 12N 30 R10 82N R12 20 R15 R18 R56 R47 10 R22 15N R39 R33 1R0 0 10 R68 R82 100 18N 47N R27 22N 1000 10000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A +16193A Agilent Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151217 / inductor_automotive_high-frequency_mlg1608_en.fm (12/12) I N D U C T O R S MLG1608 Type PACKAGING STYLE REEL DIMENSIONS ø60min. 1.0 2.0±0.5 8.4 +2.0 –0.0 ø13±0.2 14.4max. ø21±0.8 ø180±2.0 Dimensions in mm Cavity 3.5±0.05 1.5 +0.1 –0.0 Type MLG1608 A 1.9±0.2 B 1.1±0.2 K 1.1 max. A 8.0±0.3 Sprocket hole 1.75±0.1 TAPE DIMENSIONS K B 4.0±0.1 2.0±0.05 160min. Drawing direction Taping 2.0±0.05 200min. 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151217 / inductor_automotive_high-frequency_mlg1608_en.fm