MLZ1608A1R0WT000

I N D U C T O R S May 2017 Inductors for Decoupling Circuits Multilayer Ferrite MLZ Series MLZ1608 Type MLZ1608 1608 [0603 inch]* * Dimensions Code JIS[EIA] (2/10) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20170510 / inductor_commercial_decoupling_mlz1608_en.fm (3/10) I N D U C T O R S Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Inductors for Decoupling Circuits Multilayer Ferrite Overview of MLZ1608 Type FEATURES The MLZ Series include inductors for decoupling circuits that have top-class DC superimposition characteristics and low DC resistance. They are compatible with wide frequency band noise, from low to high frequency. W type products are the new standard type products that have both large current and low resistance. L type products have a resistance up to 60% lower than W type products. APPLICATION Smart phones, tablet terminals, note PCs, various modules such as camera modules, DSCs, video games, portable memory audio devices, navigation systems, PNDs, WLANs, SSDs PART NUMBER CONSTRUCTION MLZ Series name 1608 D R10 L×W×H Dimensions (mm) 1608 1.6×0.8×0.8 Product internal code A D M N Inductance (µH) R10 0.1 1R0 1 100 10 D T 000 Characteristic type Packaging style Internal code D W L High frequency type Large current type Low resistance type T Taping 000 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Package quantity Operating Storage temperature temperature (pieces/reel) （°C） （°C） MLZ1608 –55 to +125 –55 to +125 4000 Operating temperature range includes self-temperature rise. The Storage temperature range is for after the circuit board is mounted. Individual weight Type （mg） 4 RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170510 / inductor_commercial_decoupling_mlz1608_en.fm (4/10) I N D U C T O R S MLZ1608 Type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 30 to 60s Peak Temp. T4 250 to 260°C Time t3 10s max. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170510 / inductor_commercial_decoupling_mlz1608_en.fm (5/10) I N D U C T O R S MLZ1608 Type 0.80±0.15 SHAPE & DIMENSIONS 0.30±0.20 0.30±0.20 0.80±0.15 1.60±0.15 Dimensions in mm 0.8 RECOMMENDED LAND PATTERN 0.6 0.8 0.6 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170510 / inductor_commercial_decoupling_mlz1608_en.fm (6/10) I N D U C T O R S MLZ1608 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Type L (µH) 0.10 High 0.22 frequency 0.47 1.00 2.20 Large 4.70 current 10.0 22.0 1.00 2.20 Low 4.70 resistance 10.0 22.0 1 2 L measuring conditions Tolerance ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% Frequency Current (MHz) 25 25 25 10 10 2 2 2 2 2 2 2 2 (mA) 1.0 1.0 1.0 1.0 1.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 DC resistance Isat1 Itemp2 Part No. ( )±30% 0.14 0.27 0.42 0.15 0.25 0.50 1.05 2.40 0.11 0.18 0.32 0.60 1.65 (mA) 700 550 400 190 130 120 90 55 140 110 80 60 50 (mA) 850 600 500 600 500 350 250 150 700 500 400 300 190 MLZ1608DR10DT000 MLZ1608DR22DT000 MLZ1608DR47DT000 MLZ1608A1R0WT000 MLZ1608A2R2WT000 MLZ1608M4R7WT000 MLZ1608M100WT000 MLZ1608M220WT000 MLZ1608N1R0LT000 MLZ1608N2R2LT000 MLZ1608N4R7LT000 MLZ1608N100LT000 MLZ1608N220LT000 Current assumed when inductance ratio has decreased by 50% max.. Current assumed when temperature has risen to 20°C max. (reference value). Operating temperature environment at this time: 105°C max. ○ Measurement equipment Measurement item Product No. L 4294A+16034G DC resistance Type-7561 ＊ Equivalent measurement equipment may be used. Manufacturer Keysight Technologies Yokogawa Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170510 / inductor_commercial_decoupling_mlz1608_en.fm (7/10) I N D U C T O R S MLZ1608 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 M220W N220L M100W 10 N100L M4R7W N4R7L A2R2W Inductance(μH) N2R2L N1R0L 1 A1R0W DR47D DR22D DR10D 0.1 0.01 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer Keysight Technologies E4991A+16192Ａ ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170510 / inductor_commercial_decoupling_mlz1608_en.fm (8/10) I N D U C T O R S MLZ1608 Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 M220W N220L M100W 10 N100L M4R7W N4R7L Inductance(μH) A2R2W N2R2L 1 N1R0L A1R0W DR47D DR22D 0.1 DR10D 0.01 0 200 400 600 800 1000 DC current(mA) ○ Measurement equipment Product No. Manufacturer 4291B+16200A+16192A Keysight Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170510 / inductor_commercial_decoupling_mlz1608_en.fm (9/10) I N D U C T O R S MLZ1608 Type ELECTRICAL CHARACTERISTICS IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH 100000 M220W 10000 M100W N220L M4R7W N100L DR47D N4R7L 1000 N2R2L Impedance(Ω) A2R2W A1R0W DR22D N1R0L DR10D 100 10 1 1 10 100 1000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16192A Keysight Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170510 / inductor_commercial_decoupling_mlz1608_en.fm (10/10) I N D U C T O R S MLZ1608 Type PACKAGING STYLE REEL DIMENSIONS ø60min. 1.0 2.0±0.5 8.4 +2.0 –0.0 ø13±0.2 14.4max. ø21±0.8 ø180±2.0 Dimensions in mm 4.0±0.1 Cavity 3.5±0.05 1.5 +0.1 –0.0 A 8.0±0.3 Sprocket hole 1.75±0.1 TAPE DIMENSIONS K B 4.0±0.1 Dimensions in mm Type MLZ1608 160min. Drawing direction A 1.9±0.2 Taping B 1.1±0.2 K 1.1 max. 200min. 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170510 / inductor_commercial_decoupling_mlz1608_en.fm