E M C
C o m p o n e n t s
May 2018
Chip beads
For general signal line
GHz noise countermeasure (general signal line, high-speed line)
MMZ-E series
MMZ0603-E
MMZ0603-E
0603[0201 inch]*
* Dimensions code JIS[EIA]
type
(2/11)
E M C
C o m p o n e n t s
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months.Be sure to follow the storage conditions (temperature:5 to 40°C, humidity:10 to 75% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society,
person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment.
20180521 / beads_commercial_signal_mmz0603-e_en.fm
(3/11)
E M C
C o m p o n e n t s
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
Chip beads
For general signal line
GHz noise countermeasure (general signal line, high-speed line)
Overview of MMZ0603-E type
FEATURES
Noise reduction solution for general signal line.
Compared to the MMZ series, it is a product that increases the SRF to GHz bands and can countermeasure nose at wide frequencies
with 1 element.
Compared to the MMZ series, it can attain high impedance at GHz bands.
Various frequency characteristics with 4 materials of different features for countermeasures against everything from general signals to
high-speed signals.
APPLICATION
Noise removal for mobile devices such as smartphones and tablet terminals, and various modules.
Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment.
PART NUMBER CONSTRUCTION
MMZ
Series name
0603
S
L×W×T dimensions
(mm)
0603
0.6×0.3x0.3
Material name
S
A
D
F
121
E
Impedance
() at 100MHz
121
120
102
1000
Characteristic
type
E
T
000
Packaging style
Internal code
T
Taping
000
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature ranges
Operating
Storage
Type
temperature
temperature
(°C)
(°C)
MMZ0603-E
–55 to +125
–55 to +125
The storage temperature range is for after the circuit board is mounted.
Package quantity
Individual weight
(pieces/reel)
15,000
(mg)
0.3
RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html
Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_commercial_signal_mmz0603-e_en.fm
(4/11)
E M C
C o m p o n e n t s
MMZ0603-E type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1
t1
t2
t: Time
Preheating
Temp.
T1
T2
150°C
180°C
Time
t1
60 to 120s
Soldering
Temp.
Time
T3
t2
230°C
30 to 60s
Peak
Temp.
T4
250 to 260°C
Time
t3
10s
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_commercial_signal_mmz0603-e_en.fm
(5/11)
E M C
C o m p o n e n t s
MMZ0603-E type
MATERIAL CHARACTERISTIC
S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in
which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz.
A material: This high-impedance product is based on the impedance frequency characteristics of our Y-material. The product offers
excellent impedance characteristics, which is greater than 2500, in the vicinity of 100MHz range (MMZ1608A252B).
D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies.
Designed for high impedance at high frequencies (00MHz to 1GHz) for signal line applications.
F material: This new product inherits the characteristic of our D-material, namely its sharp impedance rise time, and its impedance peak
frequency has been shifted higher into range. The product offers excellent noise suppression from 600MHz to as high as in
the GHz range.
TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS
2500
A
2000
D
F
1500
1000
S
500
0
10
100
Frequency(MHz)
1000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_commercial_signal_mmz0603-e_en.fm
(6/11)
E M C
C o m p o n e n t s
MMZ0603-E type
SHAPE & DIMENSIONS
0.3±0.03
0.3±0.03
0.6±0.03
0.1min.
Dimensions in mm
0.30
RECOMMENDED LAND PATTERN
0.25
0.30
0.25
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_commercial_signal_mmz0603-e_en.fm
(7/11)
E M C
C o m p o n e n t s
MMZ0603-E type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Impedance
[100MHz]
( )
120
240
600
1000
120
240
330
470
600
1000
33
47
120
160
56
75
Tolerance
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
[1GHz]
( )
200
400
1000
1800
300
600
750
1000
1500
2300
200
300
1000
1400
700
950
Tolerance
±40%
±40%
±40%
±40%
±40%
±40%
±40%
±40%
±40%
±40%
±40%
±40%
±40%
±40%
±40%
±40%
○ Measurement equipment
Measurement item
Product No.
Impedance
E4991A+16197
DC resistance
Type-7556
* Equivalent measurement equipment may be used.
DC resistance
Rated current
Part No.
( )max.
0.37
0.71
1.60
2.60
0.44
0.86
1.00
1.30
1.70
2.90
0.6
0.76
2.4
2.90
1.9
2.6
(mA)max.
250
200
150
125
250
200
220
185
160
130
250
200
125
125
150
125
MMZ0603S121ET000
MMZ0603S241ET000
MMZ0603S601ET000
MMZ0603S102ET000
MMZ0603A121ET000
MMZ0603A241ET000
MMZ0603A331ET000
MMZ0603A471ET000
MMZ0603A601ET000
MMZ0603A102ET000
MMZ0603D330ET000
MMZ0603D470ET000
MMZ0603D121ET000
MMZ0603D161ET000
MMZ0603F560ET000
MMZ0603F750ET000
Manufacturer
Keysight Technologies
Yokogawa
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_commercial_signal_mmz0603-e_en.fm
(8/11)
E M C
C o m p o n e n t s
MMZ0603-E タイプ
ELECTRICAL CHARACTERISTICS
Z VS. FREQUENCY CHARACTERISTICS (BY SERIES)
MMZ0603S-E series
MMZ0603A-E series
2000
1800
MMZ0603S102E
1600
1200
MMZ0603S601E
1000
800
600
Impedance (Ω)
1400
1400
2000
MMZ0603A601E
MMZ0603A471E
1500
MMZ0603A331E
MMZ0603241E
1000 MMZ0603A121E
1200
1000
MMZ0603D470E
800
MMZ0603D330E
600
400
500
200
200
0
MMZ0603D121E
1600
MMZ0603S241E
400
MMZ0603D161E
1800
MMZ0603A102E
2500
Impedance(Ω)
2000
Impedance(Ω)
MMZ0603D-E series
3000
1
MMZ0603S121E
10
100
1000
10000
Frequency (MHz)
0
1
10
100
1000
Frequency (MHz)
10000
0
1
10
100
1000
Frequency (MHz)
10000
MMZ0603F-E series
2500
MMZ0603F750E
Impedance(Ω)
2000
MMZ0603F560E
1500
1000
500
0
1
10
100
1000
Frequency (MHz)
10000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_commercial_signal_mmz0603-e_en.fm
(9/11)
E M C
C o m p o n e n t s
MMZ0603-E type
ELECTRICAL CHARACTERISTICS
Z, X, R VS. FREQUENCY CHARACTERISTICS
MMZ0603S121ET000
MMZ0603S241ET000
200
Z
R
100
X
50
100
1000
Frequency (MHz)
10000
2000
1800
1600
1400
1200
1000
800
600
400
200
0
Z
R
X
1
10
100
1000
Frequency (MHz)
10000
MMZ0603A331ET000
Impedance (Ω)
Impedance (Ω)
800
Z
R
400
X
200
0
1
10
100
1000
Frequency (MHz)
10000
MMZ0603A102ET000
Impedance (Ω)
Impedance (Ω)
2500
Z
1500
R
1000
X
500
0
1
10
100
1000
Frequency (MHz)
10000
Impedance (Ω)
R
X
10
R
X
10
1400
1200
1000
800
600
400
200
0
100
1000
Frequency (MHz)
10000
R
X
10
350
300
250
200
150
100
50
0
100
1000
Frequency (MHz)
X
100
1000
Frequency (MHz)
1600
1400
1200
1000
800
600
400
200
0
10000
X
1
10
100
1000
Frequency (MHz)
10000
800
700
600
500
400
300
200
100
0
Z
R
X
1
10
100
1000
Frequency (MHz)
10000
1600
1400
1200
1000
800
600
400
200
0
Z
R
X
1
10
100
1000
Frequency (MHz)
10000
MMZ0603D470ET000
R
10
0
10000
Z
1
200
MMZ0603A601ET000
Z
1
R
400
MMZ0603A241ET000
Z
1
600
10000
100
1000
Frequency (MHz)
10000
MMZ0603F560ET000
Z
1
350
300
250
200
150
100
50
0
500
450
400
350
300
250
200
150
100
50
0
Z
R
X
1
10
100
1000
Frequency (MHz)
10000
MMZ0603F750ET000
2500
Impedance (Ω)
MMZ0603D121ET000
2000
1800
1600
1400
1200
1000
800
600
400
200
0
100
1000
Frequency (MHz)
MMZ0603D330ET000
3000
2000
10
MMZ0603A471ET000
1000
600
1
MMZ0603A121ET000
Impedance (Ω)
Impedance (Ω)
MMZ0603S102ET000
X
Impedance (Ω)
10
R
Z
800
Impedance (Ω)
1
1000
Z
Impedance (Ω)
0
1200
Z
Impedance (Ω)
150
450
400
350
300
250
200
150
100
50
0
Impedance (Ω)
Impedance (Ω)
Impedance (Ω)
250
MMZ0603S601ET000
R
X
1
10
100
1000
Frequency (MHz)
10000
2000
1500
Z R
1000
500
0
X
1
10
100
1000
Frequency (MHz)
10000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_commercial_signal_mmz0603-e_en.fm
(10/11)
E M C
C o m p o n e n t s
MMZ0603-E type
ELECTRICAL CHARACTERISTICS
Impedance (Ω)
Z, X, R VS. FREQUENCY CHARACTERISTICS
MMZ0603D161ET000
2000
1800
1600
1400
1200
1000
800
600
400
200
0
Z
R
X
1
10
100
1000
Frequency (MHz)
10000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_commercial_signal_mmz0603-e_en.fm
(11/11)
E M C
C o m p o n e n t s
MMZ0603-E type
PACKAGING STYLE
REEL DIMENSIONS
ø60min.
2.0±0.5
1.0
8.4 +2.0
–0.0
ø13±0.2
ø21±0.8
14.4max.
ø180±2.0
Dimensions in mm
4.0±0.1
B
A
8.0±0.3
2.0±0.05
3.5±0.05
1.5 +0.1
0
1.75±0.1
TAPE DIMENSIONS
P1
K
Dimensions in mm
Type
MMZ0603-E
160min.
Drawing direction
A
0.38±0.05
Taping
B
0.68±0.05
P1
2.0±0.05
K
0.5max.
200min.
300min.
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20180521 / beads_commercial_signal_mmz0603-e_en.fm