MPZ0603S800HT000

E M C C o m p o n e n t s May 2018 Chip beads For power line Large current / Low DC resistance MPZ-H series MPZ0603-H MPZ0603-H 0603[0201 inch]* * Dimensions code JIS[EIA] type (2/10) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using this products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (temperature: 5 to 40°C, humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment   (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20180529 / beads_commercial_power_mpz0603-h_en.fm (3/10) E M C C o m p o n e n t s Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Chip beads For power line Large current / Low DC resistance Overview of MPZ0603-H type FEATURES Noise reduction solution for power line. This product is a low resistance of more than 50% than 「-C」series standards. Reduced from the -C on the standard series power loss in circuits. Downsizing of 1005 shape easy due to the 50% or more improvement compared to the conventional power beads rated current. APPLICATION Noise removal for mobile devices such as smartphones and tablet terminals, and various modules. Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment. PART NUMBER CONSTRUCTION MPZ Series name 0603 L×W×T dimensions (mm) 0603 0.6×0.3x0.3 S Material name S 220 H Impedance () at 100MHz 220 22 Characteristic type H T 000 Packaging style Internal code T Taping 000 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Operating Storage temperature temperature (°C) (°C) MPZ0603-H –55 to +125 –55 to +125 The storage temperature range is for after the assembly. Package quantity Individual weight (pieces/reel) 15,000 （mg） 0.3 Type RoHS Directive Compliant Product: See the following for more details. https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180529 / beads_commercial_power_mpz0603-h_en.fm (4/10) E M C C o m p o n e n t s MPZ0603-H type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 30 to 60s Peak Temp. T4 250 to 260°C Time t3 10s Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180529 / beads_commercial_power_mpz0603-h_en.fm (5/10) E M C C o m p o n e n t s MPZ0603-H type MATERIAL CHARACTERISTIC S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz. TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS  250 200 150 100 S 50 0 10 100 Frequency(MHz) 1000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180529 / beads_commercial_power_mpz0603-h_en.fm (6/10) E M C C o m p o n e n t s MPZ0603-H type SHAPE & DIMENSIONS 0.3±0.03 0.3±0.03 0.6±0.03 0.1min. Dimensions in mm d 0.3 RECOMMENDED LAND PATTERN Solder Resist Pattern Rated current (A) 0.9max. 2.0max. 0.25 0.3 Pad thickness & d 18um 35um 70um 0.3 0.3 0.3 1.2 0.7 0.3 0.25 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180529 / beads_commercial_power_mpz0603-h_en.fm (7/10) E M C C o m p o n e n t s MPZ0603-H type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] ( ) 22 33 80 120 Tolerance ±25% ±25% ±25% ±25% DC resistance Rated current Part No. ( )max. 0.036 0.050 0.095 0.130 (mA)max. 1900 1600 1200 1000 MPZ0603S220HT000 MPZ0603S330HT000 MPZ0603S800HT000 MPZ0603S121HT000 ○ Measurement equipment Measurement item Product No. Impedance E4991A+16197 DC resistance Type-7556 ＊ Equivalent measurement equipment may be used. Manufacturer Keysight Technologies Yokogawa ○ Rated current vs. temperature characteristics (derating) 2.0 1.8 S220H Rated current (A) 1.6 1.4 1.2 1.0 S330H S800H S121H 0.8 0.6 0.4 0.2 0.0 –55 –25 5 35 65 Temperature (°C) 95 125 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180529 / beads_commercial_power_mpz0603-h_en.fm (8/10) E M C C o m p o n e n t s MPZ0603-H type ELECTRICAL CHARACTERISTICS Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MPZ0603S series 200 Impedance () 160 S121H 120 S800H 80 S330H 40 S220H 0 1 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180529 / beads_commercial_power_mpz0603-h_en.fm (9/10) E M C C o m p o n e n t s MPZ0603-H type ELECTRICAL CHARACTERISTICS Z R X 10 100 1000 Frequency (MHz) 10000 70 60 50 40 30 20 10 0 1 MPZ0603S800H Impedance () 40 35 30 25 20 15 10 5 0 1 Impedance () Impedance () Z, X, R VS. FREQUENCY CHARACTERISTICS MPZ0603S220H MPZ0603S330H Z R X 10 100 1000 Frequency (MHz) 10000 140 120 100 80 60 40 20 0 1 Z R X 10 100 1000 Frequency (MHz) 10000 Impedance () MPZ0603S121H 200 180 160 140 120 100 80 60 40 20 0 1 Z R X 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180529 / beads_commercial_power_mpz0603-h_en.fm (10/10) E M C C o m p o n e n t s MPZ0603-H type PACKAGING STYLE REEL DIMENSIONS ø60min. 2.0±0.5 1.0 8.4 +2.0 –0.0 ø13±0.2 ø21±0.8 14.4max. ø180±2.0 Dimensions in mm 4.0±0.1 B A 8.0±0.3 2.0±0.05 3.5±0.05 1.5 +0.1 0 1.75±0.1 TAPE DIMENSIONS P1 K Dimensions in mm Type MPZ0603-H 160min. Drawing direction A 0.38±0.05 Taping B 0.68±0.05 P1 2.0±0.05 K 0.5max. 200min. 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180529 / beads_commercial_power_mpz0603-h_en.fm