TCM0403T-200-2P-T210

E M C C o m p o n e n t s Common mode filters High-speed differential signal line (USB, HDMI, etc.) TCM-T series TCM0403T type ■ FEATURES ⃝ Thin-film common mode filter based on the thin-film processing techniques and material technology. ⃝ Has EMC suppression by achieving wide frequency range (cutoff frequency of 8GHz or higher) differential mode transmission while ensuring steeply common mode attenuation at high frequencies(Especially 2.4GHz and 5.0GHz bands) with virtually no affect on the high-speed differential transmission line signal. ⃝ Lineup includes 0403 (L0.45×W0.30×T0.23mm), the industry's smallest thin-film common mode filter. ⃝ Operating temperature range: –25 to +85°C ■ APPLICATION ⃝ Noise countermeasure for high-speed differential interfaces (USB, HDMI, LVDS, MIPI, etc.) for mobile devices and general consumer products such as smart phones, tablets, wearable devices, and XR devices. ■ PART NUMBER CONSTRUCTION TCM 0403 T Series name L×W×Tdimensions 0.45×0.3×0.23 mm Product identification code - 200 - Characteristic identification code 2P Number of lines - T 210 Packaging style Internal code ■ CHARACTERISTICS SPECIFICATION TABLE Common mode attenuation Cutoff frequency (dB) 30min. @5.0GHz 18min. @4.0 to 6.0GHz 35min. @2.4GHz 18min. @1.9 to 3.3GHz DC resistance Rated current Rated voltage Insulation resistance Part No. (GHz)typ. [1 line] (Ω) (A)max. (V)max. (MΩ)min. 15.0 1.2±30% 0.050 5 10 TCM0403T-080-2P-T210 8.0 3.0±30% 0.035 5 10 TCM0403T-200-2P-T210 □ Measurement equipment Measurement item Product No. Common mode impedance 4291A DC resistance 4338A Insulation resistance 4339A * Equivalent measurement equipment may be used. Manufacturer Keysight Technologies Keysight Technologies Keysight Technologies Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. (1/4) 20230222 cmf_commercial_signal_tcm0403t_en.xml E M C C o m p o n e n t s TCM0403T type ■ IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 200 Common mode Impedance (Ω) 1000 100 080 Differential mode 10 1 200 Differential mode 080 Common mode 1 10 100 Frequency (MHz) 1000 10000 □ Measurement equipment Product No. Manufacturer 4991A Keysight Technologies * Equivalent measurement equipment may be used. ■ INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 Insertion loss (dB) –10 200 Differential mode –20 080 Differential mode –30 200 Common mode 080 Common mode –40 –50 1 10 100 Frequency (MHz) 1000 10000 □ Measurement equipment Product No. Manufacturer E5071B Keysight Technologies * Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. (2/4) 20230222 cmf_commercial_signal_tcm0403t_en.xml E M C C o m p o n e n t s TCM0403T type ■ SHAPE & DIMENSIONS ■ PACKAGING STYLE □ REEL DIMENSIONS 0.30±0.02 4 2 3 E 2.0±0.5 (0.30) 0.150±0.03 ø60 –0 +1 0.23±0.02 (0.10 to 0.15) 0.45±0.02 1 1.0 9+0.3 ø13±0.2 0.075±0.030 ø21±0.8 13+1.4 +0 ø180 –3 Dimensions in mm ■ RECOMMENDED LAND PATTERN 3 Sprocket hole 1.5 +0.1 –0.0 2.0±0.5 4.0±0.1 B 0.15 8.0±0.3 0.60 0.15 1.75±0.1 2 0.20 4 0.20 1 3.5±0.05 □ TAPE DIMENSIONS 0.45 A K Cavity 2.0±0.5 ■ CIRCUIT DIAGRAM 1 4 2 3 Dimensions in mm Type A B K TCM0403T 0.35 0.50 0.27 160min. Taping 200min. • No polarity 300min. Drawing direction □ PACKAGE QUANTITY ■ RECOMMENDED REFLOW PROFILE Preheating Soldering Package quantity Natural cooling Peak 245°C Temperature 230°C 230°C 10,000 pcs/reel ■ TEMPERATURE RANGE, INDIVIDUAL WEIGHT Operating temperature range Storage temperature range * Individual weight –25 to +85 °C –25 to +85 °C 0.2 mg * 保存温度範囲は基板実装後を示します。 180°C 5s max. 150°C 60 to 120s 10 to 30s Time Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. (3/4) 20230222 cmf_commercial_signal_tcm0403t_en.xml E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using this products REMINDERS ○ The storage period is within 6 months. Be sure to follow the storage conditions (temperature: 5 to 40°C, humidity: 20 to 70% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. ○ Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). ○ Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. ○ Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. ○ When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. ○ Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. ○ Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. ○ Use a wrist band to discharge static electricity in your body through the grounding wire. ○ Do not expose the products to magnets or magnetic fields. ○ Do not use for a purpose outside of the contents regulated in the delivery specifications. ○ The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. (4/4) 20230222 cmf_commercial_signal_tcm0403t_en.xml