TCM0605T-200-2P-T201

E M C C o m p o n e n t s Common mode filters Ultra high-speed differential signal line (HDMI, DVI, DisplayPort, USB3.0, etc.) TCM-T series TCM0605T type ■ FEATURES ○This product is a thin-film common mode filter with a wide frequency range that can be used for high-speed differential signal interfaces such as USB3.0 and DisplayPort. ○ In improved common mode attenuation of 2.4GHz or 5.0GHz, produces a sufficient anti effect to common mode noise of highfrequency. Also, to realizing remarkable band differential mode transmission(8.0GHz or more), do not have an impact almost to transmission speed difference differential line signal. ○ Operating temperature range: –25 to +85°C ■ APPLICATION ○ Noise countermeasure for ultra-high-speed differential interfaces (HDMI, DVI, DisplayPort, USB3.0, etc.) for mobile devices and general consumer products such as smart phones, tablets, digital cameras, and portable music players. ■ PART NUMBER CONSTRUCTION TCM 0605 T Series name L×W×Tdimensions 0.65×0.5×0.3 mm Product identification code - 080 - Impedance (Ω) at 100MHz 2P - Number of lines T 201 Packaging style Internal code ■ CHARACTERISTICS SPECIFICATION TABLE Common mode attenuation Cutoff frequency (dB) 30min. @5.0GHz 18min. @4.0 to 6.0GHz 35min. @2.4GHz 18min. @1.9 to 3.3GHz DC resistance Rated current Rated voltage Insulation resistance Part No. (GHz)typ. [1 line] (Ω) (A)max. (V)max. (MΩ)min. 10.0 2.0±30% 0.1 10 10 TCM0605T-080-2P-T201 8.0 2.5±30% 0.1 10 10 TCM0605T-200-2P-T201 Measurement equipment Measurement item Product No. Common mode impedance 4291A DC resistance 4338A Insulation resistance 4339A * Equivalent measurement equipment may be used. Manufacturer Keysight Technologies Keysight Technologies Keysight Technologies Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. (1/4) 20230412 cmf_commercial_signal_tcm0605t_en.xml E M C C o m p o n e n t s TCM0605T type ■ IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 Impedance (Ω) 1000 200 Common mode 100 200 Differential mode 080 Differential mode 10 1 080 Common mode 1 10 100 Frequency (MHz) 1000 10000 Measurement equipment Product No. Manufacturer 4991A Keysight Technologies * Equivalent measurement equipment may be used. ■ INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 –10 Insertion loss (dB) 080 Differential mode 200 Differential mode –20 080 Common mode –30 200 Common mode –40 –50 –60 1 10 100 Frequency (MHz) 1000 10000 Measurement equipment Product No. Manufacturer E5071B Keysight Technologies * Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. (2/4) 20230412 cmf_commercial_signal_tcm0605t_en.xml E M C C o m p o n e n t s TCM0605T type ■ SHAPE & DIMENSIONS ■ PACKAGING STYLE □ REEL DIMENSIONS 0.50±0.05 4 2 3 E 2.0±0.5 0.45±0.05 +1 ø60 –0 0.20±0.05 0.30±0.05 0.03typ. 0.65±0.05 1 1.0 9+0.3 ø13±0.2 0.15±0.05 ø21±0.8 13+1.4 +0 ø180 –3 Dimensions in mm ■ RECOMMENDED LAND PATTERN Sprocket hole 2.0±0.5 4.0±0.1 2 8.0±0.3 0.25 1.5 +0.1 –0.0 1.75±0.1 0.23 4 0.71 1 3.5±0.05 □ TAPE DIMENSIONS 0.8 3 0.2 B 0.3 A K Cavity 2.0±0.5 ■ CIRCUIT DIAGRAM 1 4 2 3 Dimensions in mm Type A B K TCM0605T 0.63 0.77 0.35 160min. Taping 200min. • No polarity 300min. Drawing direction □ PACKAGE QUANTITY ■ RECOMMENDED REFLOW PROFILE Preheating Soldering Package quantity Natural cooling Peak 245°C Temperature 230°C 230°C 10,000 pcs/reel ■ TEMPERATURE RANGE, INDIVIDUAL WEIGHT Operating temperature range Storage temperature range * Individual weight –25 to +85 °C –25 to +85 °C 0.5 mg * The storage temperature range is for after the assembly. 180°C 5s max. 150°C 60 to 120s 10 to 30s Time Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. (3/4) 20230412 cmf_commercial_signal_tcm0605t_en.xml E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using this products REMINDERS ○ The storage period is within 6 months. Be sure to follow the storage conditions (temperature: 5 to 40°C, humidity: 20 to 70% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. ○ Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). ○ Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. ○ Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. ○ When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. ○ Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. ○ Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. ○ Use a wrist band to discharge static electricity in your body through the grounding wire. ○ Do not expose the products to magnets or magnetic fields. ○ Do not use for a purpose outside of the contents regulated in the delivery specifications. ○ The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. (4/4) 20230412 cmf_commercial_signal_tcm0605t_en.xml