L201E5

* Se le ct U. L. G O 1639 EC #E7 R ed Fi le c Pa ka ge s Z NI ED E1 TO-92 * TO-220 Isolated 3-lead Compak TO-252 D-Pak TO-202 TO-251 V-Pak MT2 MT1 G Sensitive Triacs (0.8 A to 8 A) E1 General Description Teccor's line of sensitive gate triacs includes devices with current capabilities through 8 A. Voltage ranges are available from 200 V to 600 V. This line features devices with guaranteed gate control in Quadrants II and IV as well as control in the commonly used Quadrants I and III. Four-quadrant control devices require sensitive gate triacs. They can be controlled by digital circuitry where positive-only or negative-only pulses must control AC current in both directions through the device. Note that triacs with low IGT values in Quadrants II and IV will have lower dv/dt characteristics. The sensitive gate triac is a bidirectional AC switch and is gate controlled for either polarity of main terminal voltage. It is used primarily for AC switching and phase control applications such as motor speed controls, temperature modulation controls, and lighting controls. The epoxy TO-92 and TO-220 configurations feature Teccor's electrically-isolated construction where the case or mounting tab is internally isolated from the semiconductor chip and lead attachments. Non-isolated epoxy TO-202 packages are available as well as TO-251 and surface mount TO-252 (D-Pak). Tapeand-reel capability and tube packing also are available. See “Packing Options” section of this catalog. All Teccor triacs have glass-passivated junctions. This glassing process prevents migration of contaminants and ensures longterm device reliability with parameter stability. Variations of devices covered in this data sheet are available for custom design applications. Consult factory for more information. Features • • • • • Electrically-isolated packages Glass-passivated junctions ensure long device reliability and parameter stability Voltage capability — up to 600 V Surge capability — up to 80 A Four-quadrant gating guaranteed Compak Sensitive Gate Triac • • • • Surface mount package — 0.8 A and 1 A series New small profile three-leaded Compak package Packaged in embossed carrier tape with 2,500 devices per reel Can replace SOT-223 http://www.teccor.com +1 972-580-7777 ©2004 Littelfuse LP Thyristor Product Catalog E1 - 1 Sensitive Triacs Data Sheets Part No. IT(RMS) (11) MT2 MT2 Isolated Non-isolated VDRM (1) IGT (3) (6) (9) IDRM (1) (14) G MT2 G MT2 MT1 MT1 G MT2 MT1 MT2 MT1 MT2 G MT1 G MT2 MT1 G MT2 mAmps Volts MIN 200 400 600 200 400 600 200 400 600 200 400 600 200 400 600 200 400 600 200 400 600 200 400 600 200 400 600 200 400 600 200 400 600 200 400 600 QI 3 3 3 5 5 5 5 5 5 10 10 10 3 3 3 5 5 5 5 5 5 10 10 10 3 3 3 5 5 5 5 5 5 10 10 10 QII QIII MAX 3 3 3 3 3 3 5 5 5 5 5 5 5 5 5 5 5 5 10 10 10 10 10 10 3 3 3 3 3 3 5 5 5 5 5 5 5 5 5 5 5 5 10 10 10 10 10 10 3 3 3 3 3 3 5 5 5 5 5 5 5 5 5 5 5 5 10 10 10 10 10 10 QIV 3 3 3 5 5 5 10 10 10 20 20 20 3 3 3 5 5 5 10 10 10 20 20 20 3 3 3 5 5 5 10 10 10 20 20 20 TO-92 MAX L2X8E3 L4X8E3 L6X8E3 L2X8E5 L4X8E5 L6X8E5 L2X8E6 L4X8E6 L6X8E6 L2X8E8 L4X8E8 L6X8E8 L201E3 L401E3 L601E3 L201E5 L401E5 L601E5 L201E6 L401E6 L601E6 L201E8 L401E8 L601E8 Compak TO-220 TO-252 D-Pak TO-202 TO-251 V-Pak 0.8 A See “Package Dimensions” section for variations. (12) L2X3 L4X3 L6X3 L2X5 L4X5 L6X5 1A L2N3 L4N3 L6N3 L2N5 L4N5 L6N5 4A L2004L3 L4004L3 L6004L3 L2004L5 L4004L5 L6004L5 L2004L6 L4004L6 L6004L6 L2004L8 L4004L8 L6004L8 L2004D3 L4004D3 L6004D3 L2004D5 L4004D5 L6004D5 L2004D6 L4004D6 L6004D6 L2004D8 L4004D8 L6004D8 L2004F31 L4004F31 L6004F31 L2004F51 L4004F51 L6004F51 L2004F61 L4004F61 L6004F61 L2004F81 L4004F81 L6004F81 L2004V3 L4004V3 L6004V3 L2004V5 L4004V5 L6004V5 L2004V6 L4004V6 L6004V6 L2004V8 L4004V8 L6004V8 mAmps TC = TC = 25 °C 110 °C MAX 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.2 0.01 0.2 0.01 0.2 0.01 0.2 0.01 0.2 0.01 0.2 0.01 0.2 0.01 0.2 0.01 0.2 0.01 0.2 0.01 0.2 0.01 0.2 See “General Notes” on page E1 - 4 and “Electrical Specification Notes” on page E1 - 5. http://www.teccor.com +1 972-580-7777 E1 - 2 ©2004 Littelfuse LP Thyristor Product Catalog Data Sheets Sensitive Triacs VTM (1) (4) VGT (2) (5) (15) IH (1) (7) IGTM (13) PGM (13) PG(AV) ITSM (8) (10) dv/dt(c) (1) (10) dv/dt (1) tgt (9) I2 t di/dt Volts TC = 25 ° C MAX 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 Volts TC = 25 ° C MAX 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Amps mAmps MAX 5 5 5 10 10 10 10 10 10 15 15 15 5 5 5 10 10 10 10 10 10 15 15 15 5 5 5 10 10 10 10 10 10 15 15 15 Amps 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 Watts 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 15 15 15 15 15 15 15 15 15 15 15 15 Watts 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 60/50 Hz 10/8.3 10/8.3 10/8.3 10/8.3 10/8.3 10/8.3 10/8.3 10/8.3 10/8.3 10/8.3 10/8.3 10/8.3 20/16.7 20/16.7 20/16.7 20/16.7 20/16.7 20/16.7 20/16.7 20/16.7 20/16.7 20/16.7 20/16.7 20/16.7 40/33 40/33 40/33 40/33 40/33 40/33 40/33 40/33 40/33 40/33 40/33 40/33 Volts/µSec TYP 0.5 0.5 0.5 1 1 1 1 1 1 2 2 2 0.5 0.5 0.5 1 1 1 1 1 1 1 1 1 0.5 0.5 0.5 1 1 1 1 1 1 2 2 2 Volts/µSec TC = 100 °C TYP 20 15 10 20 15 10 30 25 20 35 30 25 20 20 10 20 20 10 30 30 20 35 35 25 25 25 15 25 25 15 30 30 20 35 35 25 µSec TYP 2.8 2.8 2.8 3 3 3 3 3 3 3.2 3.2 3.2 2.8 2.8 2.8 3 3 3 3 3 3 3.2 3.2 3.2 2.8 2.8 2.8 3 3 3 3 3 3 3.2 3.2 3.2 Amps2Sec 0.41 0.41 0.41 0.41 0.41 0.41 0.41 0.41 0.41 0.41 0.41 0.41 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 6.6 6.6 6.6 6.6 6.6 6.6 6.6 6.6 6.6 6.6 6.6 6.6 Amps/µSec 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 50 50 50 50 50 50 50 50 50 50 50 50 See “General Notes” on page E1 - 4 and “Electrical Specification Notes” on page E1 - 5. ©2004 Littelfuse LP Thyristor Product Catalog E1 - 3 http://www.teccor.com +1 972-580-7777 Sensitive Triacs Data Sheets Part No. IT(RMS) (11) MT2 MT2 Isolated Non-isolated VDRM (1) IGT (3) (6) IDRM (1) (14) G MT2 MT1 MT1 MT2 G MT1 G MT2 TO-220 MAX TO-252 D-Pak TO-251 V-Pak Volts MIN 200 400 600 200 400 600 200 400 600 200 400 600 200 400 600 QI 5 5 5 5 5 5 10 10 10 5 5 5 10 10 10 6A 8A See “Package Dimensions” section for variations. (12) L2006L5 L2006D5 L2006V5 L4006L5 L4006D5 L4006V5 L6006L5 L6006D5 L6006V5 L2006L6 L2006D6 L2006V6 L4006L6 L4006D6 L4006V6 L6006L6 L6006D6 L6006V6 L2006L8 L2006D8 L2006V8 L4006L8 L4006D8 L4006V8 L6006L8 L6006D8 L6006V8 L2008L6 L2008D6 L2008V6 L4008L6 L4008D6 L4008V6 L6008L6 L6008D6 L6008V6 L2008L8 L2008D8 L2008V8 L4008L8 L4008D8 L4008V8 L6008L8 L6008D8 L6008V8 mAmps QII QIII MAX 5 5 5 5 5 5 5 5 5 5 5 5 10 10 10 10 10 10 5 5 5 5 5 5 10 10 10 10 10 10 QIV 5 5 5 10 10 10 20 20 20 10 10 10 20 20 20 mAmps TC = 25 °C TC = 110 °C MAX 0.02 0.5 0.02 0.5 0.02 0.5 0.02 0.5 0.02 0.5 0.02 0.5 0.02 0.5 0.02 0.5 0.02 0.5 0.02 0.5 0.02 0.5 0.02 0.5 0.02 0.5 0.02 0.5 0.02 0.5 Specified Test Conditions di/dt — Maximum rate-of-change of on-state current; IGT = 50 mA with 0.1 µs rise time dv/dt — Critical rate-of-rise of off-state voltage at rated VDRM gate open dv/dt(c) — Critical rate-of-rise of commutation voltage at rated VDRM and IT(RMS) commutating di/dt = 0.54 rated IT(RMS)/ms; gate unenergized I2t — RMS surge (non-repetitive) on-state current for period of 8.3 ms for fusing IDRM — Peak off-state current, gate open; VDRM = max rated value IGT — DC gate trigger current in specific operating quadrants; VD = 12 V dc; RL = 60 Ω IGTM — Peak gate trigger current IH — Holding current gate open; initial on-state current = 100 mA dc IT(RMS) — RMS on-state current conduction angle of 360° ITSM — Peak one-cycle surge PG(AV) — Average gate power dissipation PGM — Peak gate power dissipation; IGT ≤ IGTM tgt — Gate controlled turn-on time; IGT = 50 mA with 0.1 µs rise time VDRM — Repetitive peak off-state/blocking voltage VGT — DC gate trigger voltage; VD = 12 V dc; RL = 60 Ω VTM — Peak on-state voltage at max rated RMS current General Notes • • • All measurements are made with 60 Hz resistive load and at an ambient temperature of +25 °C unless otherwise specified. Operating temperature range (TJ) is -65 °C to +110 °C for TO-92 devices and -40 °C to +110 °C for all other devices. Storage temperature range (TS) is -65 °C to +150 °C for TO-92 devices, -40 °C to +150 °C for TO-202 devices, and -40 °C to +125 °C for TO-220 devices. Lead solder temperature is a maximum of 230 °C for 10 seconds maximum at a minimum of 1/16” (1.59 mm) from case. The case or lead temperature (TC or TL) is measured as shown on dimensional outline drawings. See “Package Dimensions” section of this catalog. • • http://www.teccor.com +1 972-580-7777 E1 - 4 ©2004 Littelfuse LP Thyristor Product Catalog Data Sheets Sensitive Triacs VTM (1) (4) VGT (2) (5) (15) IH (1) (7) IGTM (13) PGM (13) PG(AV) ITSM (8) (10) dv/dt(c) (1) (10) dv/dt (1) tgt (9) I2 t di/dt Volts TC = 25 °C MAX 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 Volts TC = 25 °C MAX 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 mAmps MAX 10 10 10 10 10 10 20 20 20 10 10 10 20 20 20 Amps 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 Watts 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 Watts 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 Amps 60/50 Hz 60/50 60/50 60/50 60/50 60/50 60/50 60/50 60/50 60/50 80/65 80/65 80/65 80/65 80/65 80/65 Volts/µSec TYP 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 Volts/µSec TC = 100 °C TYP 40 30 20 40 30 20 45 40 30 40 30 20 45 40 30 µSec TYP 3 3 3 3 3 3 3.2 3.2 3.2 3 3 3 3.2 3.2 3.2 Amps2Sec 15 15 15 15 15 15 15 15 15 26.5 26.5 26.5 26.5 26.5 26.5 Amps/µSec 70 70 70 70 70 70 70 70 70 70 70 70 70 70 70 Electrical Specification Notes (1) (2) (3) (4) (5) (6) (7) (8) (9) For either polarity of MT2 with reference to MT1 terminal For either polarity of gate voltage VGT with reference to MT1 terminal See Gate Characteristics and Definition of Quadrants. See Figure E1.4 for iT versus vT. See Figure E1.6 for VGT versus TC. See Figure E1.7 for IGT versus TC. See Figure E1.5 for IH versus TC. See Figure E1.9 for surge rating and specific duration. See Figure E1.8 for tgt versus IGT. Gate Characteristics Teccor triacs may be turned on between gate and MT1 terminals in the following ways: • • In-phase signals (with standard AC line) using Quadrants I and III Application of unipolar pulses (gate always positive or negative), using Quadrants II and III with negative gate pulses and Quadrants I and IV with positive gate pulses When maximum surge capability is required, pulses should be a minimum of one magnitude above IGT rating with a steep rising waveform (≤1 µs rise time). ALL POLARITIES ARE REFERENCED TO MT1 MT2 POSITIVE (Positive Half Cycle) (10) See Figure E1.2 and Figure E1.3 for maximum allowable case temperature at maximum rated current. (11) See Figure E1.1, Figure E1.2, and Figure E1.3 for TA or TC versus IT(RMS). (12) See package outlines for lead form configurations. When ordering special lead forming, add type number as suffix to part number. (13) Pulse width ≤10 µs (14) TC or TL = TJ for test conditions in off state (15) Minimum non-trigger VGT at 110 °C is 0.2 V. IGT (-) MT2 IGT GATE + MT2 (+) IGT GATE MT1 MT1 (-) REF MT2 IGT GATE MT1 REF QII QI QIII QIV (+) REF + MT2 IGT GATE MT1 REF IGT MT2 NEGATIVE (Negative Half Cycle) - Definition of Quadrants ©2004 Littelfuse LP Thyristor Product Catalog E1 - 5 http://www.teccor.com +1 972-580-7777 Sensitive Triacs Data Sheets Electrical Isolation Teccor’s isolated triac packages withstand a minimum high potential test of 2500 V ac rms from leads to mounting tab over the device's operating temperature range. The following isolation table shows standard isolation ratings. Electrical Isolation from Leads to Mounting Tab V AC RMS 2500 *UL Recognized File #E71639 TO-220 * Standard Thermal Resistance (Steady State) Junction to Mounting Tab and Junction to Ambient RθJC [RθJA] °C/W (TYP) Package Code E C F L F2 D V Type TO-92 Plastic 0.8 A 1A 4A 6A 8A 60 [135] 50 [95] Compak 60 * 40 * TO-202 Type 1 TO-220 Isolated TO-202 Type 2 TO-252 D-Pak TO-251 V-Pak 3.5 [45] 3.6 [50] 3.3 2.8 6.0 [70] 3.5 3.2 2.7 6.0 [70] 3.2 2.7 * Mounted on 1 cm2 copper foil surface; two-ounce copper foil Maximum Allowable Ambient Temperature (TA) - ˚C 120 Maximum Allowable Case Temperature (TC) – ˚C 100 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360˚ FREE AIR RATING – NO HEATSINK TO-220 and TYPE 1 and 3 TO-202 110 100 90 80 70 0.8 A CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360˚ CASE TEMPERATURE: Measured as shown on Dimensional Drawings 80 TYPE 2 and 4 TO-202 and TO-251 1A 60 1 A TO-92 40 0.8 A TO-92 60 50 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 25 20 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 RMS On-State Current [IT(RMS)] – Amps RMS On-State Current [IT(RMS)] - Amps Figure E1.1 Maximum Allowable Ambient Temperature versus On-state Current Figure E1.2 Maximum Allowable Case Temperature versus On-state Current (0.8 A and 1 A) http://www.teccor.com +1 972-580-7777 E1 - 6 ©2004 Littelfuse LP Thyristor Product Catalog Data Sheets Sensitive Triacs Maximum Allowable Case Temperature (TC) - ˚C 110 105 100 95 90 85 80 75 70 65 60 0 1 2 3 4 5 6 7 8 4 A TYPE 2 and 4 TO-202 4 A TO-251 4 A TYPE 1 and 3 TO-202 4 A TO-220 (Isolated) 4 A TO-252 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360˚ CASE TEMPERATURE: Measured as shown on Dimensional Drawings 2.0 6A TO TO -25 8A 1a -22 nd TO 0( TO -22 Iso -25 0( 2 lat Iso ed late ) d) 8A VGT (TC = 25 ˚C) 1.5 VGT 1.0 6 A TO-251 6 A TO-252 Ratio of .5 0 -65 -40 -15 +25 +65 +110 +125 RMS On-State Current [IT(RMS)] - Amps Case Temperature (TC) - ˚ C Figure E1.3 Maximum Allowable Case Temperature versus On-state Current (4 A, 6 A, and 8 A) Figure E1.6 Normalized DC Gate Trigger Voltage for All Quadrants versus Case Temperature 20 18 TC = 25 ˚ C 4.0 Positive or Negative Instantaneous On-state Current (iT) - Amps 16 14 12 10 8 6 4 2 0 0 0.5 0.8 1.0 1.2 1.4 1.6 1.8 0.8 A 4A 1A 6 A and 8 A IGT (T = 25 ˚C) C 3.0 IGT 2.0 Ratio of 1.0 0 -65 -40 -15 +25 +65 +110 +125 Positive or Negative Instantaneous On-state Voltage (vT) - Volts Case Temperature (TC) - ˚C Figure E1.4 On-state Current versus On-state Voltage (Typical) Figure E1.7 Normalized DC Gate Trigger Current for All Quadrants versus Case Temperature 7.0 4.0 TC = 25 ˚C 6.0 IH (TC = 25 ˚C) 3.0 Turn-On Time (tgt) - µSec INITIAL ON-STATE CURRENT = 100 mA (DC) 0.8 - 4 A Devices = 200 mA (DC) 6 - 8 A Devices IGT = 5 mA MAX 5.0 IGT = 10 mA MAX IH 4.0 2.0 IGT = 20 mA MAX Ratio of 3.0 IGT = 3 mA MAX 1.0 2.0 1.0 0 -65 -40 -15 +25 +65 +110 +125 0 1 2 3 4 56 8 10 20 30 40 60 80 100 Case Temperature (TC) - ˚C DC Gate Trigger Current (IGT) - mA Figure E1.5 Normalized DC Holding Current versus Case Temperature Figure E1.8 Turn-on Time versus Gate Trigger Current (Typical) ©2004 Littelfuse LP Thyristor Product Catalog E1 - 7 http://www.teccor.com +1 972-580-7777 Sensitive Triacs Data Sheets 200 150 100 80 60 40 30 20 10 8 6 4 3 2 1 1 2 34 6 8 10 20 30 40 60 100 200 400 600 1000 8A 6A 4A SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-state Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Peak Surge (Non-Repetitive) On-State Current (ITSM) – Amps NOTES: 1) Gate control may be lost during and immediately following surge current interval. 2) Overload may not be repeated until junction temperature has returned to steady-state rated value. 1A 0.8 A Surge Current Duration – Full Cycles Figure E1.9 Peak Surge Current versus Surge Current Duration 9.0 8.0 7.0 6.0 6 A and 8 A Average On-state Power Dissipation [PD(AV)] – Watts 1.5 1.0 Average On-state Power Dissipation [PD(AV)] – Watts CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360˚ CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360˚ 5.0 4.0 3.0 2.0 1.0 4A 0.8 A 0.5 1A 0 0 0.25 0.50 0.75 1.0 1.25 1.5 0 0 .5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 RMS On-state Current [IT(RMS)] – Amps RMS On-state Current [IT(RMS)] – Amps Figure E1.10 Power Dissipation (Typical) versus RMS On-state Current (0.8 A and 1 A) Figure E1.11 Power Dissipation (Typical) versus RMS On-state Current (4 A, 6 A, and 8 A) http://www.teccor.com +1 972-580-7777 E1 - 8 ©2004 Littelfuse LP Thyristor Product Catalog