S2020L

l Se ec te U. L. G O 1639 EC #E7 R d P Fi le k ac ag es * NI ZE D TO-263 D 2 Pak TO-92 * TO-218 TO-252 D-Pak TO-202 * TO-218X 3-lead Compak * TO-220 TO-251 V-Pak A K G (1 A to 70 A) E6 General Description The Teccor line of thyristor SCR semi-conductors are half-wave, unidirectional, gate-controlled rectifiers which complement Teccor's line of sensitive SCRs. Teccor offers devices with ratings of 1 A to 70 A and 200 V to 1000 V, with gate sensitivities from 10 mA to 50 mA. If gate currents in the 12 µA to 500 µA ranges are required, see “Sensitive SCRs” section of this catalog. Three packages are offered in electrically isolated construction where the case or tab is internally isolated to allow the use of low-cost assembly and convenient packaging techniques. The Teccor line of SCRs features glass-passivated junctions to ensure long-term reliability and parameter stability. Teccor’s glass offers a rugged, reliable barrier against junction contamination. Variations of devices covered in this data sheet are available for custom design applications. Consult the factory for more information. Features • • • • Electrically-isolated package High voltage capability — 200 V to 1000 V High surge capability — up to 950 A Glass-passivated chip Compak SCR • • • • Surface mount package — 1 A series New small profile three-leaded Compak package Packaged in embossed carrier tape with 2,500 devices per reel Can replace SOT-223 ©2002 Teccor Electronics Thyristor Product Catalog E6 - 1 http://www.teccor.com +1 972-580-7777 SCRs Data Sheets Part Number Isolated A Non-isolated A IT (1) (2) (15) VDRM & VRRM IGT (4) A G TYPE A A A G K K K G A K A G K K A G G A K A G TO-92 TO-220 TO-202 TO-220 TO-251 V-Pak Compak TO-252 D-Pak Amps IT(RMS) IT(AV) MAX 0.64 0.64 0.64 3.8 3.8 3.8 3.8 3.8 5.1 5.1 5.1 5.1 5.1 6.4 6.4 6.4 6.4 6.4 7.6 7.6 7.6 7.6 7.6 Volts MIN 200 400 600 200 400 600 800 1000 200 400 600 800 1000 200 400 600 800 1000 200 400 600 800 1000 mAmps MIN 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 MAX 10 10 10 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 20 20 20 20 20 MAX 1 1 1 See “Package Dimensions” section for variations. (11) 1A S201E S401E S601E S2006L S2006F1 S4006F1 S6006F1 S2006V S4006V S6006V S8006V SK006V S2008F1 S4008F1 S6008F1 S2008R S4008R S6008R S8008R SK008R S2010F1 S4010F1 S6010F1 S2010R S4010R S6010R S8010R SK010R S2012R S4012R S6012R S8012R SK012R S2008V S4008V S6008V S8008V SK008V S2010V S4010V S6010V S8010V SK010V S2012V S4012V S6012V S8012V SK012V S4006L S6006L S8006L SK006L S2008L S4008L S6008L S8008L SK008L S2010L S2N1 S4N1 S6N1 S2006D S4006D S6006D S8006D SK006D S2008D S4008D S6008D S8008D SK008D S2010D S4010D S6010D S8010D SK010D S2012D S4012D S6012D S8012D SK012D 6 6 6 6 6 8 8 8 8 8 10 10 10 10 10 12 12 12 12 12 6A 8A 10 A S4010L S6010L S8010L SK010L 12 A Specific Test Conditions di/dt — Maximum rate-of-rise of on-state current; IGT = 150 mA with £ 0.1 µs rise time dv/dt — Critical rate of applied forward voltage I2t — RMS surge (non-repetitive) on-state current for period of 8.3 ms for fusing IDRM and IRRM — Peak off-state forward and reverse current at VDRM and VRRM Igt — dc gate trigger current; VD = 12 V dc; RL = 60 W for 1 to 16 A devices and 30 W for 20 to 70 A devices IGM — Peak gate current IH — dc holding current; gate open IT — Maximum on-state current ITSM — Peak one-cycle forward surge current PG(AV) — Average gate power dissipation PGM — Peak gate power dissipation tgt — Gate controlled turn-on time; gate pulse = 100 mA; minimum width = 15 µs with rise time £ 0.1 µs tq — Circuit commutated turn-off time VDRM and VRRM — Repetitive peak off-state forward and reverse voltage Vgt — DC gate trigger voltage; VD = 12 V dc; RL = 60 W for 1 to 16 A devices and 30 W for 20 to 70 A devices VTM — Peak on-state voltage at maximum rated RMS current General Notes • • • All measurements are made at 60 Hz with a resistive load at an ambient temperature of +25 °C unless otherwise specified. Operating temperature range (TJ) is -65 °C to +125 °C for TO-92 devices and -40 °C to +125 °C for all other packages. Storage temperature range (TS) is -65 °C to +150 °C for TO-92 devices, -40 °C to +150 °C for TO-202 and TO-220 devices, and -40 °C to +125 °C for all others. Lead solder temperature is a maximum of 230 °C for 10 seconds maximum; ³1/16" (1.59 mm) from case. The case temperature (TC) is measured as shown on dimensional outline drawings in the “Package Dimensions” sectionof this catalog. • • http://www.teccor.com +1 972-580-7777 E6 - 2 ©2002 Teccor Electronics Thyristor Product Catalog Data Sheets SCRs IDRM & IRRM (14) VTM (3) VGT (8) (17) IH (5) (13) IGM (12) PGM (12) PG(AV) ITSM (6) (10) dv/dt I2t di/dt tgt (7) tq (9) (10) mAmps TC = 25 °C 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.02 0.01 0.01 0.01 0.01 0.02 0.01 0.01 0.01 0.02 0.02 0.01 0.01 0.01 0.02 0.02 TC = TC = 100 °C 125 °C MAX 0.2 0.2 0.2 0.2 0.2 0.2 0.2 3 0.2 0.2 0.2 0.2 3 0.2 0.2 0.2 0.5 3 0.5 0.5 0.5 0.5 3 1 1 1 1 0.5 0.5 0.5 1 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 Volts TC = 25 °C MAX 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 Volts TC = 25 °C MAX 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 mAmps MAX 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 40 40 40 40 40 1.5 1.5 1.5 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 15 15 15 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 0.3 0.3 0.3 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 Amps Watts Watts Amps 60/50 Hz 30/25 30/25 30/25 100/83 100/83 100/83 100/83 100/83 100/83 100/83 100/83 100/83 100/83 100/83 100/83 100/83 100/83 100/83 120/100 120/100 120/100 120/100 120/100 Volts/µSec TC = 100 °C MIN 40 40 40 350 350 300 250 100 350 350 300 250 100 350 350 300 250 100 350 350 300 250 100 250 250 225 200 250 250 225 200 250 250 225 200 TC = 125 °C MIN 20 20 20 250 250 225 200 3.7 3.7 3.7 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 60 60 60 60 60 50 50 50 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 Amps2Sec Amps/µSec µSec TYP 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 µSec MAX 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 Electrical Specification Notes (1) (2) (3) (4) (5) (6) (7) (8) (9) See Figure E6.5 through Figure E6.16 for current rating at specified operating case temperature. See Figure E6.1 and Figure E6.2 for free air current rating. See Figure E6.19 and Figure E6.20 for instantaneous on-state current versus on-state voltage (typical). See Figure E6.18 for IGT versus TC. See Figure E6.17 for IH versus TC. For more than one full cycle rating, see Figure E6.23. See Figure E6.22 for tgt versus IGT. See Figure E6.21 for VGT versus TC. Test conditions are as follows: • IT = 1 A for 1 A devices and 2 A for all other devices • Pulse duration = 50 µs, dv/dt = 20 V/µs, di/dt = -10 A/µs for 1 A devices, and -30 A/µs for other devices • IGT = 200 mA at turn-on (10) See Figure E6.5 through Figure E6.10 for maximum allowable case temperatures at maximum rated current. (11) See package outlines for lead form configuration. When ordering special lead forming, add type number as suffix to part number. (12) Pulse width £10 µs (13) Initial on-state current = 200 mA dc for 1 A through 16 A devices; 400 mA dc for 20 A through 70 A devices. (14) TC = TJ for test conditions in off state. (15) The R, K, or M package rating is intended for high surge condition use only and not recommended for ³50 A rms continuous current use since narrow pin lead temperature can exceed PCB solder melting temperature. Teccor's J package or W package is recommended for ³50 A rms continuous current requirements. (16) For various durations of an exponentially decaying current waveform, see Figure E6.3 and Figure E6.4. (tW is defined as 5 time constants.) (17) Minimum non-trigger VGT at 125 °C is 0.2 V. ©2002 Teccor Electronics Thyristor Product Catalog E6 - 3 http://www.teccor.com +1 972-580-7777 SCRs Data Sheets Part Number Isolated A Non-isolated A A IT (1) (15) A A A K G VDRM & VRRM IGT (4) IDRM & IRRM (14) TYPE K A G A K A G KAG K AG K A G KAG Amps TO-263 D2Pak IT(RMS) 15 15 15 15 15 IT(AV) 9.5 9.5 9.5 9.5 9.5 10 10 10 10 10 12.8 12.8 12.8 12.8 12.8 16 16 16 16 16 22 22 22 22 22 25 25 25 25 25 35 35 35 35 35 41 41 41 41 41 45 45 45 45 Volts MIN 200 400 600 800 1000 200 400 600 800 1000 200 400 600 800 1000 200 400 600 800 1000 200 400 600 800 1000 200 400 600 800 1000 200 400 600 800 1000 200 400 600 800 1000 200 400 600 800 mAmps MIN 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 MAX 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 35 35 35 35 35 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 50 50 50 50 50 50 50 50 50 0.01 0.01 0.01 0.02 0.02 0.01 0.01 0.01 0.02 0.02 0.01 0.01 0.01 0.02 0.02 0.01 0.01 0.01 0.02 0.02 0.01 0.01 0.01 0.02 0.02 0.01 0.01 0.01 0.02 0.03 0.01 0.01 0.01 0.02 0.03 0.02 0.02 0.02 0.02 0.03 0.02 0.02 0.02 0.02 TC = 25 °C mAmps TC = 100 °C MAX 0.5 0.5 0.5 1 3 0.5 0.5 0.5 1 3 0.5 0.5 0.5 1.0 3 1 1 1 1.5 3 1 1 1 1.5 3 1 1 1 1.5 5 1 1 1 1.5 5 1.5 1.5 1.5 2 5 1.5 1.5 1.5 2 3 3 3 5 3 3 3 5 2 2 2 3 2 2 2 3 2 2 2 3 2 2 2 3 1 1 1 2 1 1 1 2 1 1 1 2 TC = 125 °C TO-220 S2015L TO-218X TO-218 TO-220 TO-218X TO-218 See “Package Dimensions” section for variations. (11) S4015L S6015L S8015L SK015L S2016R S2016N S4016N S6016N S8016N SK016N S4016R S6016R S8016R SK016R S2020L S4020L S6020L S8020L SK020L S2025L S2025R S4025R S6025R S8025R SK025R S2035J S2035K S4035K S6035K S8035K SK035K S2040R S2040N S4040N S6040N S8040N SK040N S2055W S4055W S6055W S8055W S2055M S4055M S6055M S8055M SK055M S2055N S4055N S6055N S8055N SK055N S4040R S6040R S8040R SK040R S2055R S4055R S6055R S8055R SK055R S2065J S2065K S4065K S6065K S8065K SK065K S2070W S4070W S6070W S8070W S4065J S6065J S8065J S4035J S6035J S8035J S2025N S4025N S6025N S8025N SK025N S4025L S6025L S8025L SK025L MAX 15 A 16 16 16 16 16 20 20 20 20 20 25 25 25 25 25 35 35 35 35 35 40 40 40 40 40 55 55 55 55 55 65 65 65 65 65 70 70 70 70 16 A 20 A 25 A 35 A 40 A 55 A 65 A 70 A See “General Notes” on page E6 - 2 and “Electrical Specification Notes” on page E6 - 3. http://www.teccor.com +1 972-580-7777 E6 - 4 ©2002 Teccor Electronics Thyristor Product Catalog Data Sheets SCRs VTM (3) VGT (8) (17) IH (5) (13) IGM (12) PGM (12) PG(AV) ITSM (6) (10) (16) dv/dt I2 t di/dt tgt (7) tq (9) (10) Volts Volts mAmps MAX 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 50 50 50 50 50 50 50 50 50 50 60 60 60 60 60 60 60 60 60 60 80 80 80 80 80 80 80 80 80 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 4 4 4 4 4 5 5 5 5 5 5 5 5 5 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 40 40 40 40 40 50 50 50 50 50 50 50 50 50 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 1 1 1 1 1 1 1 1 1 Amps Watts Watts Amps 60/50 Hz 225/188 225/188 225/188 225/188 225/188 225/188 225/188 225/188 225/188 225/188 300/255 300/255 300/255 300/255 300/255 350/300 350/300 350/300 350/300 350/300 500/425 500/425 500/425 500/425 500/425 520/430 520/430 520/430 520/430 520/430 650/550 650/550 650/550 650/550 650/550 950/800 950/800 950/800 950/800 950/800 950/800 950/800 950/800 950/800 Volts/µSec TC = 100 °C MIN 450 450 425 400 200 450 450 425 400 200 450 450 425 400 200 450 450 425 400 200 450 450 425 400 200 650 650 600 500 250 650 650 600 500 250 650 650 600 500 250 650 650 600 500 550 550 500 475 550 550 500 475 550 550 500 475 550 550 500 475 350 350 325 300 350 350 325 300 350 350 325 300 350 350 325 300 TC = 125 °C MIN 350 350 325 300 210 210 210 210 210 210 210 210 210 210 374 374 374 374 374 510 510 510 510 510 1035 1035 1035 1035 1035 1122 1122 1122 1122 1122 1750 1750 1750 1750 1750 3745 3745 3745 3745 3745 3745 3745 3745 3745 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 150 150 150 150 150 150 150 150 150 150 175 175 175 175 175 175 175 175 175 175 200 200 200 200 200 200 200 200 200 Amps2Sec Amps/µSec µSec TYP 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 µSec MAX 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 TC = 25 °C TC = 25 °C MAX 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 MAX 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 2 2 2 2 2 2 2 2 2 See “General Notes” on page E6 - 2 and “Electrical Specification Notes” on page E6 - 3. ©2002 Teccor Electronics Thyristor Product Catalog E6 - 5 http://www.teccor.com +1 972-580-7777 SCRs Data Sheets Thermal Resistance (Steady State) RqJC [RqJA] °C/W (TYP.) Pkg. Code L F F2 R J W K M D V N Type TO-220 Isolated TO-202 Type 1 Non-isolated 4.3 [45] 3.9 3.4 TO-202 Type 2 Non-isolated 9.5 [70] TO-220 Non-isolated TO-218X Isolated TO-218X Non-isolated See below TO-218 Isolated TO-218 Non-isolated TO-252 TO-251AA D-Pak V-Pak Surface Mount Non-isolated 1.7 2.3 [70] 2.0 1.7 1.6 TO-263 D2Pak Non-isolated 1A 6A 8A 10 A 12 A 15 A 16 A 20 A 25 A 35 A 40 A 55 A 65 A 70 A 4.0 [50] 3.4 3.0 2.5 1.8 [40] 1.6 1.5 1.3 1.5 1.45 1.4 1.3 1.0 0.70 0.70 0.6 0.53 0.86 0.60 0.86 0.53 0.5 2.4 2.35 1.0 0.6 0.5 Electrical Isolation Thermal Resistance (Steady State) RqJC [RqJA] °C/W (TYP.) Package Code Type C E Teccor’s isolated SCR packages will withstand a minimum high potential test of 2500 V ac rms from leads to mounting tab over the device's operating temperature range. The following table shows standard and optional isolation ratings. Electrical Isolation * from Leads to Mounting Tab TO-220 TO-218X Isolated Isolated Standard Optional ** Standard N/A 1A Compak 35 * TO-92 50 [145] V AC RMS 2500 4000 TO-218 Isolated Standard N/A * Mounted on 1cm2 copper foil surface; two-ounce copper foil * UL Recognized File #E71639 ** For 4000 V isolation, use “V” suffix in part number. http://www.teccor.com +1 972-580-7777 E6 - 6 ©2002 Teccor Electronics Thyristor Product Catalog Data Sheets SCRs 120 Maximum Allowable Ambient Temperature (TA) – ˚C 8 A TO-220 (Non-isolated) 80 Normalized Peak Current 100 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ FREE AIR RATING 1.0 0.8 0.6 0.4 0.2 0 25 50 75 100 125 6 A TO-220 (Isolated) and 6 A TO-202 (Types 1 and 3) 60 1 A TO-92 40 6 A TO-202 (Types 2 and 4) and 6 A TO-251 20 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 Case Temperature (TC) – ˚C RMS On-state Current [IT(RMS)] – Amps Figure E6.1 Maximum Allowable Ambient Temperature versus RMS On-state Current Figure E6.4 Peak Capacitor Discharge Current Derating (6 A through 55 A) 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ FREE AIR RATING 130 120 Maximum Allowable Ambient Temperature (TA) – ˚C 100 Maximum Allowable Case Temperature (TC) – ˚C 110 100 90 80 70 60 50 0 0.2 0.4 0.6 0.8 1.0 1.2 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ CASE TEMPERATURE: Measure as shown on dimensional drawing 8 A TO-220 (Non-isolated) 80 1 A Devices 1 A TO-92 60 6 A TO-220 (Isolated) and 6 A TO-202 (Types 1 and 3) 40 6 A TO-202 (Types 2 and 4) and 6 A TO-251 20 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 Average On-state Current [IT(AV)] – Amps RMS On-state Current [IT(RMS)] – Amps Figure E6.2 Maximum Allowable Ambient Temperature versus Average On-state Current Figure E6.5 Maximum Allowable Case Temperature versus RMS On-state Current (1 A) 130 Peak Discharge Current (ITM) – Amps 1000 120 55 A Devices 8 A TO-220 (Non-isolated) TO-251 and TO-252 10 A TO-220 (Isolated) and 10 A TO-202 Maximum Allowable Case Temperature (TC) – ˚C 110 6 A Devices 100 90 80 70 60 50 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180º CASE TEMPERATURE: Measure as shown on dimensional drawings 0 2 4 6 8 300 200 25 A Devices 15 A and 16 A Devices 8 A TO-220 (Isolated) and 8 A TO-202 100 6 A to 10 A Devices 12 A Devices 50 ITM tw tw = 5 times constants 20 0.5 1.0 2.0 5.0 10 20 50 10 12 Pulse Current Duration (tw) – ms RMS On-state Current [IT(RMS)] – Amps Figure E6.3 Peak Capacitor Discharge Current (6 A through 55 A) Figure E6.6 Maximum Allowable Case Temperature versus RMS On-state Current (6 A, 8 A, and 10 A) ©2002 Teccor Electronics Thyristor Product Catalog E6 - 7 http://www.teccor.com +1 972-580-7777 SCRs Data Sheets 130 130 Maximum Allowable Case Temperature (TC) – ˚C 120 110 100 90 80 70 60 50 0 55 A TO-220 (Non-isolated) and TO-263 * Maximum Allowable Case Temperature (TC) – ˚C 120 110 100 90 80 70 60 50 0 4 10 A TO-220 (Non-isolated) 16 A TO-220 (Non-isolated) and TO-263 20 A TO-220 (Isolated) CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ CASE TEMPERATURE: Measure as shown on dimensional drawings 55 A TO-218AC (Non-isolated) * 10 A TO-251 and 10 A TO-252 12 A TO-220 (Non-isolated) TO-251 and TO-252 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ CASE TEMPERATURE: Measure as shown on dimensional drawing 65 A TO-218AC (Isolated) * * The R, K or M package rating is intended only for high surge condition use and is not recommended for >50 A rms continuous current use, since narrow pin lead temperature can exceed PCB solder melting temperature. J or W packages are recommended for >50 A rms continuous current requirements. 10 20 30 40 50 60 70 75 15 A TO-220 (Isolated) 8 12 16 20 RMS On-state Current [IT(RMS)] – Amps RMS On-state Current [IT(RMS)] – Amps Figure E6.7 Maximum Allowable Case Temperature versus RMS On-state Current (10 A, 12 A, 16 A, and 20 A) Figure E6.10 Maximum Allowable Case Temperature versus RMS On-state Current (55 A and 65 A) Maximum Allowable Case Temperature (TC) – ˚C 130 120 130 120 110 100 Maximum Allowable Case Temperature (TC) – ˚C 110 100 90 80 70 60 50 0 25 A TO-220 (Isolated) 25 A TO-220 (Non-isolated) and TO-263 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ CASE TEMPERATURE: Measure as shown on dimensional drawings 4 8 12 16 20 24 28 35 A TO-218 (Isolated) 1 A Devices 90 80 70 60 32 36 50 0 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ CASE TEMPERATURE: Measure as shown on dimensional drawings 0.2 0.4 0.6 0.8 RMS On-state Current [IT(RMS)] – Amps Average On-state Current [IT(AV)] – Amps Figure E6.8 Maximum Allowable Case Temperature versus RMS On-state Current (25 A and 35 A) 130 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ CASE TEMPERATURE: Measure as shown on dimensional drawings Figure E6.11 Maximum Allowable Case Temperature versus Average On-state Current (1 A) Maximum Allowable Case Temperature (TC) – ˚C 130 12 A TO-220 (Non-isolated) and TO-251 and TO-252 Maximum Allowable Case Temperature (TC) – ˚C 120 10 A TO-251 10 A TO-252 110 100 90 80 70 60 50 0 10 20 30 40 50 60 70 40 A TO-220 (Non-isolated) and TO-263 65 A TO-218X (Isolated) CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ CASE TEMPERATURE: Measure as shown on dimensional drawings 70 A TO-218X (Non-isolated) 110 6 A TO-220 6 A TO-202 10 A TO-220 (Non-isolated) 10 A TO-220 (Isolated) and 10 A TO-202 100 6 A TO-251 6 A TO-252 8 A TO-220 (Isolated) 8 A TO-202 55 A TO-218X (Non-isolated) 90 8 A TO-220 (Non-isolated) 80 0 1 2 3 4 5 6 7 8 RMS On-state Current [IT(RMS)] – Amps Average On-state Current [IT(AV)] – Amps Figure E6.9 Maximum Allowable Case Temperature versus RMS On-state Current (40 A through 70 A) Figure E6.12 Maximum Allowable Case Temperature versus Average On-state Current (8 A, 10 A, and 12 A) http://www.teccor.com +1 972-580-7777 E6 - 8 ©2002 Teccor Electronics Thyristor Product Catalog Data Sheets SCRs 130 130 16 AT O-2 20 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ CASE TEMPERATURE: Measured as shown on dimensional drawings 120 Case Temperature (TC) – ˚C 110 100 90 80 70 60 50 0 120 Case Temperature (TC) – ˚C 110 100 90 80 70 60 50 0 55 A TO-220 (Non-isolated) and TO-263 * (No n-is olat Maximum Allowable ed) -26 3 20 A TO-220 (Isolated) Maximum Allowable and CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ CASE TEMPERATURE: Measure as shown on dimensional drawings 55 A TO-218AC (Non-isolated) * TO 65 A TO-218AC (Isolated) * 10 A TO-220 (Non-isolated) * The R, K, or M package rating is intended only for high surge condition use and is not recommended for >32 A (AV) continuous current use since narrow pin lead temperature can exceed PCB solder melting temperature. J or W packages are recommended for >32 A (AV) continuous current requirements. 15 A TO-220 (Isolated) 2 4 6 8 10 12 14 10 20 30 40 50 Average On-state Current [IT(AV)] – Amps Average On-state Current [IT(AV)] – Amps Figure E6.13 Maximum Allowable Case Temperature versus Average On-state Current (10 A through 20 A) Figure E6.16 Maximum Allowable Case Temperature versus Average On-state Current (55 A and 65 A) 130 Maximum Allowable Case Temperature (TC) – ˚C 120 110 IH (TC = 25 ˚C) CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ CASE TEMPERATURE: Measure as shown on dimensional drawings 2.0 INITIAL ON-STATE CURRENT = 200 mA dc for 1 A to 20 A Devices and 400 mA dc for 25 A to 70 A Devices 1.5 35 A TO-218 (Non-isolated) 100 IH 35 A TO-218 (Isolated) 90 1.0 80 Ratio of 25A TO-220 (Isolated) .5 70 60 25A TO-220 (Non-isolated) and TO-263 0 50 0 .4 8 12 16 20 24 -40 -15 +25 +65 +105 +125 Case Temperature (TC) – ˚C Average On-state Current [IT(AV)] – Amps Figure E6.14 Maximum Allowable Case Temperature versus Average On-state Current (25 A and 35 A) 130 120 Maximum Allowable Case Temperature (TC) – ˚C CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ CASE TEMPERATURE: Measure as shown on dimensional drawings Figure E6.17 Normalized dc Holding Current versus Case Temperature 2.0 110 100 90 80 40 A TO-220 (Non-isolated) and TO-263 55 A TO-218X (Non-isolated) 65 A TO-218X (Isolated) IGT (TC = 25 ˚C) 1.5 70 A TO-218X (Non-isolated) IGT Ratio of 1.0 70 60 50 0 0.5 0 10 20 30 40 50 -40 -15 +25 +65 +105 +125 Average On-state Current [IT(AV)] – Amps Case Temperature (TC) – ˚C Figure E6.15 Maximum Allowable Case Temperature versus Average On-state Current (40 A through 70 A) Figure E6.18 Normalized DC Gate-Trigger Current versus Case Temperature ©2002 Teccor Electronics Thyristor Product Catalog E6 - 9 http://www.teccor.com +1 972-580-7777 SCRs Data Sheets 90 Instantaneous On-state Current (iT) – Amps 1.5 80 70 60 50 VGT (TC = 25 ˚C) TC = 25˚C 25 A Devices 15 A to 20 A Devices 40 12 A Devices 30 VGT 6 A to 10 A Devices 1.0 20 10 Ratio of 1 A Devices 0.5 0 0 0 0.6 0.8 1.0 1.2 1.4 1.6 -40 -15 +25 +65 +105 +125 Case Temperature (TC) – ˚C Instantaneous On-state Voltage (vT) – Volts Figure E6.19 Instantaneous On-state Current versus On-state Voltage (Typical) (6 A through 25 A) Figure E6.21 Normalized DC Gate-trigger Voltage versus Case Temperature 200 180 7 6 A to 12 A Devices TC = 25˚C 15 A to 35 A Devices Turn-on Time (tgt) – µs 160 Instantaneous On-state Current (iT) – Amps 140 120 100 80 60 40 20 0 0 TC = 25˚C 6 5 65 A and 70 A Devices 4 40 A to 70 A Devices 3 1 A Devices 55 A Devices 2 1 35 A to 40 A Devices .6 .8 1.0 1.2 1.4 1.6 0 10 20 30 40 50 60 80 100 200 Instantaneous On-state Voltage (vT) – Volts DC Gate Trigger Current (IGT) – mA Figure E6.20 Instantaneous On-state Current versus On-state Voltage (Typical) (35 A through 70 A) Figure E6.22 Typical Turn-on Time versus Gate-trigger Current http://www.teccor.com +1 972-580-7777 E6 - 10 ©2002 Teccor Electronics Thyristor Product Catalog Data Sheets SCRs Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps 1000 800 600 500 400 300 200 65 A SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS ON-STATE CURRENT: [IT(RMS)]: MaxRated Value at Specified Case Temperature TO-2 18 70 A Devic Devic es 35 A 25 A 16 A 10 A Devic es Devic 55 A Devic es es es 40 A Devic es es 100 80 60 50 40 30 20 Devic 20 A 15 A Devic es Devic es 12 A Devic es 8AD evice s 6A Dev ices 10 8 6 5 4 3 2 1A Dev Notes: 1) Gate control may be lost during and immediately following surge current interval. 2) Overload may not be repeated until junction temperature has returned to steady-state rated value. ices 1 1 2 3 4 5 6 7 8 10 20 30 40 60 80100 200 300400 600 1000 Surge Current Duration – Full Cycles Figure E6.23 Peak Surge Current versus Surge Current Duration Average On-state Power Dissipation [PD(AV)] – Watts Average On-state Power Dissipation [PD(AV)] – Watts CURRENT WAVEFORM: Half Sine Wave LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ 18 16 14 12 10 8 6 4 2 0 15 A to 20 A Devices 12 A Devices 6 A to 10 A Devices CURRENT WAVEFORM: Half Sine Wave LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ 1.0 0.8 1.0 A Devices 0.6 0.4 0.2 0 0 0.2 0.4 0.6 0.8 1.0 0 2 4 6 8 10 12 14 16 18 20 RMS On-state Current [IT(RMS)] – Amps Figure E6.24 Power Dissipation (Typical) versus RMS On-state Current (1 A) RMS On-state Current [IT(RMS)] – Amps Figure E6.25 Power Dissipation (Typical) versus RMS On-state Current (6 A through 20 A) ©2002 Teccor Electronics Thyristor Product Catalog E6 - 11 http://www.teccor.com +1 972-580-7777 SCRs Data Sheets 32 60 Average On-state Power Dissipation [PD(AV)] x– Watts 28 24 20 16 12 8 Power Dissipation [PD(AV)] – Watts es CURRENT WAVEFORM: Half Sine Wave LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ Average On-state 25 4 0 0 4 8 A TO 0 22 D ic ev es 20 10 0 12 16 20 24 28 32 36 0 10 20 30 40 50 60 70 RMS On-state Current [IT(RMS)] – Amps Figure E6.26 Power Dissipation (Typical) versus RMS On-state Current (25 A and 35 A) RMS On-state Current [IT(RMS)] – Amps Figure E6.27 Power Dissipation (Typical) versus RMS On-state Current (40 A through 70 A) http://www.teccor.com +1 972-580-7777 E6 - 12 40 30 A an d 55 35 A A De De vi c v s ice 50 CURRENT WAVEFORM: Half Sine Wave LOAD: Resistive or Inductive CONDUCTION ANGLE: 180˚ d 70 A De vic es 40 65 A an ©2002 Teccor Electronics Thyristor Product Catalog