MPS2907

Transys Electronics LIMITED PNP SILICON PLANAR EPITAXIAL TRANSISTORS MPS2907 MPS2907A TO-92 Plastic Package General Purpose Transistors ABSOLUTE MAXIMUM RATINGS(Ta=25ºC unless specified otherwise) DESCRIPTION SYMBOL MPS2907 Collector Emitter Voltage Collector Base Voltage Emitter Base Voltage Collector Current Continuous Power Dissipation @ Ta=25ºC Derate Above 25ºC Power Dissipation @ Tc=25ºC Derate Above 25ºC Operating And Storage Junction Temperature Range THERMAL RESISTANCE Junction to ambient Junction to case VCEO VCBO VEBO IC PD PD Tj, Tstg 40 60 5 600 625 5 1.5 12 -55 to +150 MPS2907A 60 75 UNITS V V V mA mW mW/ºC W mW/ºC ºC Rth(j-a) Rth(j-c) 200 83.3 ºC/W ºC/W PNP SILICON PLANAR EPITAXIAL TRANSISTORS MPS2907 MPS2907A TO-92 Plastic Package ELECTRICAL CHARACTERISTICS (Ta=25ºC Unless Specified Otherwise) DESCRIPTION SYMBOL TEST CONDITION Collector Emitter Voltage Collector Base Voltage Emitter-Base Voltage Collector-Cut off Current BVCEO * BVCBO BVEBO ICBO VCB=50V, IE = 0 VCB=50V, IE = 0, Collector-Cut off Current Collector-Cut off Current Emitter Cut off Current Base Cut off Current Collector-Emitter Saturation Voltage Base-Emitter Saturation Voltage DC Current Gain hFE VCE=10V,IC=0.1mA VCE=10V,IC=1mA VCE=10V,IC=10mA VCE=10V*,IC=150mA VCE=10V*,IC=500mA ELECTRICAL CHARACTERISTICS (Ta=25ºC Unless Specified Otherwise) DYNAMIC CHARACTERISTICS SYMBOL TEST CONDITION ICEX ICEO IEBO IBEX VCE(sat)* VBE(sat)* TA = 150 C VCE=30V, VEB(off)=0.5V VCE=10V VEB=3V, IC = 0 VCE=30V,VEB(off)=0.5V IC=150mA,IB=15mA IC=500mA,IB=50mA IC=150mA,IB=15mA IC=500mA,IB=50mA 0 IC=10mA,IB=0 IC=10µA,IE=0 IE=10µA, IC=0 MPS2907 MIN MAX 40 60 5 20 20 50 10 10 50 0.4 1.6 1.3 2.6 35 50 75 100 30 300 MPS2907A MIN MAX 60 60 5 10 10 50 10 10 50 0.4 1.6 1.3 2.6 75 100 100 100 50 300 UNITS V V V nA µA nA nA nA nA V V V V µA MPS2907 MIN MAX MPS2907A MIN MAX UNITS Transition Frequency f T*(1) IC=50mA, VCE=20V f=100MHz IE=0, VCB=10V f=1MHz Ic=0, VEB=2V f=1MHz 200 200 MHz Output Capacitance Input Capacitance Cob Cib 8 30 8 30 PF PF PNP SILICON PLANAR EPITAXIAL TRANSISTORS MPS2907 MPS2907A TO-92 Plastic Package SWITCHING CHARCTERISTICS SYMBOL TEST CONDITION IC =150mA,IB1 =15mA, VCC =30V td tr ton MPS2907 MIN MAX 10 40 45 MPS2907A MIN MAX 10 40 45 UNITS Delay Time Rise Time Turn On Time ns ns ns IC =150mA, IB1= IB2 15mA, VCC =6V Storage Time Fall Time ts tf 80 30 100 80 30 100 ns ns ns toff Turn Off Time *Pulse Condition: Width < 300us, Duty Cycle < 2%. (1) fT is defined as the frequency at which IhfeI extrapolates to unity. MPS2907 MPS2907A TO-92 Plastic Package TO-92 Plastic Package TO-92 Transistors on Tape and Ammo Pack Dimension With 'L' B Uncontrolled Ammo Pack Style MECHANICAL DATA T P h A A1 (p) Adhesive Tape on Top Side D FEE Carrier Strip 183 mm h LABEL FLAT SIDE A H1 H0 L W2 Wo W1 W L Solderability Ensured t1 t F1 F P2 Po F2 Do 331 mm 42 mm Beyond 'L' K 1 2 3 D G AA Flat Side of Transistor and Adhesive Tape Visible 2000 pcs./Ammo Pack All dimensions in mm unless specified otherwise D 3 E 2 1 ITEM BODY WIDTH BODY HEIGHT BODY THICKNESS PITCH OF COMPONENT FEED HOLE PITCH FEED HOLE CENTRE TO COMPONENT CENTRE DISTANCE BETWEEN OUTER LEADS COMPONENT ALIGNMENT TAPE WIDTH HOLD-DOWN TAPE WIDTH HOLE POSITION HOLD-DOWN TAPE POSITION LEAD WIRE CLINCH HEIGHT COMPONENT HEIGHT LENGTH OF SNIPPED LEADS FEED HOLE DIAMETER TOTAL TAPE THICKNESS LEAD - TO - LEAD DISTANCEF1, CLINCH HEIGHT PULL - OUT FORCE SYMBOL A1 A T P Po P2 F h W Wo W1 W2 Ho H1 L Do t F2 H2 (P) SEC AA DIM MIN. 4.32 4.45 3.18 0.41 MAX. 5.33 5.20 4.19 0.55 F F 321 A B C D E F G H K L PIN CONFIGURATION 1. COLLECTOR 2. BASE 3. EMITTER 0.35 0.50 5 DEG 1.14 1.40 1.14 1.53 12.70 1.982 — 2.082 SPECIFICATION REMARKS MIN. NOM. MAX. TOL . 4.0 4.8 5.2 4.8 4.2 3.9 12.7 ±1 12.7 ±0.3 CUMULATIVE PITCH ERROR 1.0 mm/20 PITCH 6.35 ±0.4 TO BE MEASURED AT BOTTOM OF CLINCH +0.6 5.08 -0.2 0 1 AT TOP OF BODY 18 ±0.5 6 ±0.2 9 +0.7 -0.5 0.5 ±0.2 16 ±0.5 23.25 11.0 4 ±0.2 1.2 t1 0.3 - 0.6 2.54 +0.4 -0.1 3 6N H C All diminsions in mm. NOTES 1. MAXIMUM ALIGNMENT DEVIATION BETWEEN LEADS NOT TO BE GREATER THAN 0.2 mm. 2. MAXIMUM NON-CUMULATIVE VARIATION BETWEEN TAPE FEED HOLES SHALL NOT EXCEED 1 mm IN 20 PITCHES. 3. HOLDDOWN TAPE NOT TO EXCEED BEYOND THE EDGE(S) OF CARRIER TAPE AND THERE SHALL BE NO EXPOSURE OF ADHESIVE. 4. NO MORE THAN 3 CONSECUTIVE MISSING COMPONENTS ARE PERMITTED. 5. A TAPE TRAILER, HAVING AT LEAST THREE FEED HOLES ARE REQUIRED AFTER THE LAST COMPONENT. 6. SPLICE S S HALL NO T INTERFERE WITH THE SPROC KET FEED H OLE S. Packing Detail PACKAGE TO-92 Bulk TO-92 T&A STANDARD PACK Details Net Weight/Qty 1K/polybag 200 gm/1K pcs 2K/ammo box 645 gm/2K pcs INNER CARTON BOX Size Qty 3" x 7.5" x 7.5" 5K 12.5" x 8" x 1.8" 2K OUTER CARTON BOX Size Qty Gr Wt 17" x 15" x 13.5" 80K 23 kgs 17" x 15" x 13.5" 32K 12.5 kgs