0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
78P2352-IGT

78P2352-IGT

  • 厂商:

    TERIDIAN

  • 封装:

  • 描述:

    78P2352-IGT - Dual Channel OC-3/ STM1-E/ E4 LIU - Teridian Semiconductor Corporation

  • 数据手册
  • 价格&库存
78P2352-IGT 数据手册
78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU DATA SHEET SEPTEMBER 2006 DESCRIPTION The 78P2352 is Teridian’s second generation Line Interface Unit (LIU) for 155 Mbps SDH/SONET (OC-3, STS-3, or STM-1) and 140 Mbps PDH (E4) telecom interfaces. The device is a dual channel, single chip solution that includes an integrated CDR in the transmit path for flexible NRZ to CMI conversion. The device can interface to 75Ω coaxial cable using CMI coding or directly to a fiber optics transceiver module using NRZ coding. The 78P2352 is compliant with all respective ANSI, ITUT, and Telcordia standards for jitter tolerance, generation, and transfer. FEATURES • • • • • • • • • • ITU-T G.703 compliant cable driver for 139.264 Mbps or 155.52 Mbps CMI-coded coax transmission Integrated adaptive CMI equalizer and CDR in receive path handles over 12.7dB of cable loss Serial, LVPECL system interface with integrated CRU in transmit path for flexible NRZ to CMI conversion. 4-bit parallel CMOS system interface with master and slave Tx clock modes. Selectable LVPECL compatible NRZ media interface for 155.52 Mbps optical transmission. Configurable via HW control pins or 4-wire serial port interface Compliant with ANSI T1.105.03-1994; ITU-T G.751, G.813, G.823, G.825, G.958; and Telcordia GR-253-CORE for jitter performance. Receiver Loss of Signal (LOS) detection compatible with ITU-T G.783 Operates from a single 3.3V supply Standard and thermally enhanced 128-pin JEDEC LQFP package options APPLICATIONS • • • • • Central Office Interconnects DSLAMs Add Drop Multiplexers (ADMs) Multi Service Switches Digital Microwave Radios BLOCK DIAGRAM Lock Detect SIxDP/N SIxCKP/N PIxCK PIx[3:0]D PTOxCK Tx CDR EACH CHANNEL: Tx ECLxP/N FIFO CMI Encoder TXxCKP/N CMIxP/N PMOD, SMOD[1:0], PAR RLBK SOxCKP/N SOxDP/N POx[3:0]D POxCK CMI Decoder Rx CDR Lock Detect CMI EACH CHANNEL: Rx Adaptive Eq. RXxP/N LOS Detect LLBK Page: 1 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU TABLE OF CONTENTS ................................................................................................ 2 FUNCTIONAL DESCRIPTION........................................................................................ 4 MODE SELECTION................................................................................................................................4 REFERENCE CLOCK ............................................................................................................................4 RECEIVER OPERATION .......................................................................................................................4 Receiver Monitor Mode ..................................................................................................................4 Receive Loss of Signal ..................................................................................................................5 Receive Loss of Lock.....................................................................................................................5 TRANSMITTER OPERATION ................................................................................................................5 Synchronous (Re-timing) Tx Serial Modes ..................................................................................5 Plesiochronous Serial Modes .......................................................................................................6 Synchronous Parallel Modes ........................................................................................................6 Transmit FIFO Description ............................................................................................................6 Transmit Driver ...............................................................................................................................7 Clock Synthesizer...........................................................................................................................7 Transmit Backplane Equalizer ......................................................................................................7 Transmit Loss of Lock ...................................................................................................................7 POWER-DOWN FUNCTION .................................................................................................................7 ANALOG LOOPBACK MODES.............................................................................................................7 POWER-ON RESET ..............................................................................................................................7 SERIAL CONTROL INTERFACE .........................................................................................................8 PROGRAMMABLE INTERRUPTS ........................................................................................................8 REGISTER DESCRIPTION............................................................................................. 9 REGISTER ADDRESSING.....................................................................................................................9 REGISTER TABLE.................................................................................................................................9 LEGEND ...............................................................................................................................................10 GLOBAL REGISTERS .........................................................................................................................10 ADDRESS 0-0: MASTER CONTROL REGISTER .......................................................................10 ADDRESS 0-1: INTERRUPT CONTROL REGISTER..................................................................11 PORT-SPECIFIC REGISTERS ............................................................................................................12 ADDRESS N-0: MODE CONTROL REGISTER...........................................................................12 ADDRESS N-1: SIGNAL CONTROL REGISTER ........................................................................13 ADDRESS N-2: ADVANCED TX CONTROL REGISTER 1 ........................................................14 ADDRESS N-3: ADVANCED TX CONTROL REGISTER 0 ........................................................14 ADDRESS N-4: MODE CONTROL REGISTER 2........................................................................14 ADDRESS N-5: STATUS MONITOR REGISTER ........................................................................15 PIN DESCRIPTION ....................................................................................................... 16 LEGEND ...............................................................................................................................................16 TRANSMITTER PINS ...........................................................................................................................16 RECEIVER PINS ..................................................................................................................................17 REFERENCE AND STATUS PINS ......................................................................................................18 CONTROL PINS ..................................................................................................................................19 SERIAL-PORT PINS ............................................................................................................................21 POWER AND GROUND PINS .............................................................................................................21 Page: 2 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU TABLE OF CONTENTS (continued) ELECTRICAL SPECIFICATIONS ................................................................................. 22 ABSOLUTE MAXIMUM RATINGS..........................................................................................................22 RECOMMENDED OPERATING CONDITIONS ......................................................................................22 DC CHARACTERISTICS.........................................................................................................................22 ANALOG PINS CHARACTERISTICS.....................................................................................................23 DIGITAL I/O CHARACTERISTICS..........................................................................................................23 Pins of type CI, CIU, CID ................................................................................................................23 Pins of type CIT ..............................................................................................................................23 Pins of type CIS ..............................................................................................................................23 Pins of type CO and COZ ...............................................................................................................24 Pins of type PO ...............................................................................................................................24 Pins of type PI.................................................................................................................................24 Pins of type OD...............................................................................................................................24 SERIAL-PORT TIMING CHARACTERISTICS........................................................................................25 TRANSMITTER TIMING CHARACTERISTICS ......................................................................................26 TIMING DIAGRAM: Transmitter Waveforms .......................................................................................26 REFERENCE CLOCK CHARACTERISTICS..........................................................................................27 RECEIVER TIMING CHARACTERISTICS..............................................................................................27 TIMING DIAGRAM: Receive Waveforms ............................................................................................27 TRANSMITTER SPECIFICATIONS FOR CMI INTERFACE .................................................................28 TRANSMITTER OUTPUT JITTER ..........................................................................................................33 RECEIVER SPECIFICATIONS FOR CMI INTERFACE (Transformer-coupled)..................................34 RECEIVER JITTER TOLERANCE ..........................................................................................................35 RECEIVER JITTER TRANSFER FUNCTION .........................................................................................37 CMI MODE LOSS OF SIGNAL CONDITION ..........................................................................................38 APPLICATION INFORMATION .................................................................................... 38 EXTERNAL COMPONENTS ...................................................................................................................38 (CMI) TRANSFORMER SPECIFICATIONS............................................................................................38 THERMAL INFORMATION .....................................................................................................................38 MECHANICAL SPECIFICATIONS ............................................................................... 39 PACKAGE INFORMATION (pinout)................................................................................................ 41 ORDERING INFORMATION ......................................................................................... 41 Revision History ........................................................................................................................................42 Page: 3 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU FUNCTIONAL DESCRIPTION The 78P2352 contains all the necessary transmit and receive circuitry for connection between 139.264Mbps and 155.52Mbps line interfaces and the digital universe. The chip is controllable through pins or serial port register settings. In hardware mode (pin control) the SPSL pin must be low. In software mode (SPSL pin high), control pins are disabled and the 78P2352 must be configured via the 4-wire serial port. MODE SELECTION The SDO_E4 pin or E4 register bit determines which rate the device (both channels) operates in according to the table below. This control, combined with CKSL, also selects the global reference clock frequency. Rate E4 STM-1, STS-3, OC-3 SDO_E4 pin High Low E4 bit 1 0 The frequency of this reference input is controlled by the rate selection and the CKSL control pin or register bit. CKSL pin Low Float High CKSL[1:0] bits 00 10 11 Reference Frequency SDO_E4 low SDO_E4 high 19.44MHz 77.76MHz 155.52MHz E4 bit = 0 19.44MHz 77.76MHz 155.52MHz 17.408MHz N/A 139.264MHz E4 bit = 1 17.408MHz N/A 139.264MHz RECEIVER OPERATION The receiver accepts serial data, at 155.52Mbps or 139.264Mbps from the RXxP/N inputs. In CMI mode, the input is differentially terminated with 75Ω and transformer-coupled to a coaxial connector. In Fiber (NRZ) mode, the input is differentially terminated with 100Ω and AC-coupled to an optical transceiver module. For board designs utilizing both coax and fiber media options, an analog switch or mechanical relay is required to switch between the different terminations and media paths. The CMI signal first enters an AGC and adaptive equalizer designed to overcome inter-symbol interference caused by long cable lengths. The variable gain differential amplifier automatically controls the gain to maintain a constant voltage level output regardless of the input voltage level. Note that in Fiber (NRZ) mode, the input signals bypass the adaptive equalizer. The outputs of the data comparators are connected to the clock recovery circuits. The clock recovery system employs a Delay Locked Loop (DLL), which uses a reference frequency derived from the clock applied to the CKREFP/N pins. In serial mode, the clock and data are decoded and transmitted through the LVPECL drivers. In parallel mode, the data is decoded and converted into four bit parallel segments before being transmitted through the CMOS drivers. Note that in Fiber (NRZ) mode, the CMI decoder is bypassed. Receiver Monitor Mode In CMI mode, the SCK_MON pin or MONx register bit enables the receiver’s monitor mode which adds approximately 20dB of flat gain to the receive signal before equalization. Rx Monitor Mode can handle 20dB of flat loss typical of monitoring points with up to 6dB of cable loss. Note that Loss of Signal detection is disabled during Rx Monitor Mode. The SEN_CMI pin or CMI register bit enables the CMI encoder/decoder and selects one of two media for reception and transmission: 75Ω coaxial cable in CMI mode or optical fiber in Fiber (NRZ) mode. Independent channel operation for media type is available with register controls only. Media (coding) 75Ω Coax (CMI) Fiber (NRZ) SEN_CMI pin High Low CMI bit 1 0 The SDI_PAR pin or PAR register bit selects the interface to the framer to be 4-bit parallel CMOS or serial LVPECL. For each interface there are different transmit timing modes available. See TRANSMITTER OPERATION section for more info. REFERENCE CLOCK The 78P2352 requires a reference clock supplied to the CKREFP/N pins. This reference clock is used for clock recovery in the Rx DLL and Tx DLL. It is also used for transmit re-timing in the synchronous transmit modes. Refer to the TRANSMITTER OPERATION section for timing requirements during synchronous (re-timing) transmit modes. For reference frequencies of 77.76MHz or lower, the device accepts a single ended CMOS input at CKREFP (with CKREFN grounded). For reference frequencies of 139.264 or 155.52MHz, the device accepts a differential LVPECL clock input at CKREFP/N. Page: 4 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU Receive Loss of Signal The 78P2352 includes a Loss of Signal (LOS) detector. When the peak value of the received CMI signal is less than approximately 19dB below nominal for approximately 110 UI, Receive Loss of Signal is asserted. The Rx LOS signal is cleared when the received signal is greater than approximately 18dB below nominal for 110 UI. In ECL mode, the LOSx signal will be asserted when there are no transitions for longer than 2.3µs. The signal is cleared when there are more than 4 transitions in 32 UI. It is generally recommended to use the LOS status signal from the optical transceiver module. During Rx LOS conditions, the receive clock will remain on the last selected phase tap of the Rx DLL outputting a stable clock while the receive data outputs are squelched and held at logic ‘0’. Note: Rx Loss of Signal detection is disabled during Local Loopback and Receive Monitor Modes. Receive Loss of Lock The 78P2352 includes an optional Receiver Loss of Lock detector that will flag if the recovered Rx clock frequency differs from the reference clock by more than ±100ppm in an interval greater than 420µs. This condition is cleared when the frequencies are less than ±100ppm off for more than 500µs. Notes: 1. During Rx Loss of Signal (RLOS), the Rx Loss of Lock indicator is undefined and may report either status. 2. For reliable operation, the LOLOR bit in the Signal Control register should be toggled upon power-up and configuration. TRANSMITTER OPERATION At the media interface, the transmit driver generates an analog signal for transmission through either a transformer and 75Ω coaxial cable or directly to a fiber optics transceiver for electrical to optical conversion. At the host interface, the 78P2352 provides a number interface options for compatibility with most off-the-shelf framers and custom ASICs. A selectable 4-bit parallel or nibble interface is available with both slave or master timing options as well a serial LVPECL interface with various timing recovery modes. Each of the serial NRZ transmit timing modes can be configured in HW mode or SW mode as shown in the table below. Serial Mode Synchronous clock + data Synchronous data only Plesiochronou s data only Loop-timing HW Control Pins SW Control Bits SDI_PAR Low Low Low n/a CKMODE Low Floating High n/a PAR 0 0 0 X SMOD[1:0] 00 10 01 11 Synchronous (Re-timing) Tx Serial Modes In Figure 1, serial NRZ transmit data is input to SIDxP/N pins at LVPECL levels. By default, the data is latched in on the rising edge of SICKxP. An integrated FIFO decouples the on chip and off chip clocks and re-clocks the data using a clean synthesized clock generated from the provided reference clock. As such, the SICKxP/N clock provided by the framer/mapper IC for both channels must be source synchronous with the provided reference clock when the FIFO is used. System Reference Clock CKREFP/N NRZ SIxDP/N CMI CMIxP/N 140 / 155 MHz XFMR Coax Framer/ Mapper SIxCKP/N NRZ SOxCKP/N TDK 78P2352 RXxP/N 140 / 155 MHz CMI SOxDP/N XFMR Coax Figure 1: Synchronous clock and data available (Tx CDR bypassed, FIFO enabled) If an off-chip serial transmit clock is not available, as in Figure 2, the 78P2352 can recover a Tx clock from the serial NRZ data input and pass the data through the clock decoupling FIFO. The data is then re-clocked or re-timed using a clean synthesized clock generated from the provided reference clock. In this mode, the NRZ transmit source data for both channels must be source synchronous with the reference clock applied at CKREFP/N. System Reference Clock CKREFP/N NRZ SIxDP/N CMIxP/N CMI XFMR Coax Framer/ Mapper NRZ 140 / 155 MHz SOxCKP/N SOxDP/N TDK 78P2352 RXxP/N CMI XFMR Coax Figure 2: Synchronous data only (Tx CDR enabled, FIFO enabled) Page: 5 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU Plesiochronous Tx Serial Mode Figure 3 represents a common condition where a serial transmit clock is not available and/or the data is not source synchronous to the reference clock input. In this mode, the 78P2352 will recover a transmit clock from the serial plesiochronous data and bypass the internal FIFO and re-timing block. This mode is commonly used for mezzanine cards, modules, and any application where the reference clock cannot always be synchronous to the transmit source clock/data. Reference Clock XO Reference Clock CKREFP/N 4-bit CMOS TTL PIx[3:0]D PIxCK CMIxP/N CMI XFMR Coax Framer/ Mapper 34/39 MHz 4-bit CMOS TTL 34/39 MHz POx[3:0]D POxCK TDK 78P2352 RXxP/N CMI XFMR Coax Figure 4: Slave Parallel Mode Reference Clock CKREFP/N 4-bit CMOS TTL CKREFP PIx[3:0]D PTOxCK CMIxP/N CMI XFMR Coax NRZ SIxDP/N CMIxP/N CMI XFMR Coax Framer/ Mapper 34/39 MHz 4-bit CMOS TTL 34/39 MHz Framer/ Mapper NRZ 140 / 155 MHz SOxCKP/N SOxDP/N TDK 78P2352 RXxP/N POx[3:0]D POxCK TDK 78P2352 RXxP/N CMI XFMR Coax CMI XFMR Coax Figure 5: Master Parallel Mode Figure 3: Plesiochronous; data only (Tx CDR enabled, FIFO bypassed) Synchronous Parallel Modes In parallel modes, 4-bit CMOS data segments are input to the chip with a 34.816MHz (E4 ÷ 4) or 38.88MHz (STM1 ÷ 4) synchronous clock. These inputs are re-timed in a 4x8 clock decoupling FIFO and then to a serializer for transmission. Because the data is passed through the FIFO and re-timed using a synthesized clock, the transmit nibble clock and data for both channels must be source synchronous to the provided reference clock. For maximum compatibility with legacy ASICs, the 78P2352 can operate in both slave and master clock modes as shown in Figures 4 and 5 respectively. Note: A loop-timing mode is also available to allow external remote loopbacks (i.e. line loopback in framer). In this mode, the FIFO is still enabled, but the transmit data will be retimed using the recovered receive clock Parallel Mode Slave Slave + *Loop-timing Master Transmit FIFO Description Since the reference clock and transmit clock/data go through different delay paths, it is inevitable that the phase relationship between the two clocks can vary in a bounded manner due to the fact that the absolute delays in the two paths can vary over time. The transmit FIFO allows long-term clock phase drift between the Tx clock and system reference clock, not exceeding +/- 25.6ns, to be handled without transmit error. If the clock wander exceeds the specified limits, the FIFO will over or under flow, and the FERRx register signal will be asserted. This signal can be used to trigger an interrupt. This interrupt event is automatically cleared when a FIFO Reset (FRSTx) pulse is applied, and the FIFO is recentered. Notes: 1) External remote loopbacks (i.e. loopback within framer) are not possible in synchronous operation (FIFO enabled) unless the data is re-justified to be synchronous to the system reference clock or the 78P2352 is configured for loop-timing. 2) Most E4 applications will not allow the use of the dual channel 78P2352 as each channel is asynchronous to each other. Teridian recommends using the single channel 78P2351 if one cannot control the E4 timing reference for each channel. 3) During IC power-up or transmit power-up, the clocks going to the FIFO may not be stable and cause the FIFO to overflow or underflow. As such, the FIFO should be manually reset using FRST anytime the transmitter is powered-up. Rev. 2.4 HW Control Pins SDI_PAR High High High CKMODE Low Float High SW Control Bits PAR 1 1 1 PMODE 0 0 1 *To enable Loop-timing SMOD[1:0]=11 in software mode set Page: 6 of 42 2006 Teridian Semiconductor Corporation 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU Transmit Driver In CMI (electrical) mode, the CMIxP/N pins are biased and terminated off-chip. They interface to 75Ω coaxial cable through a 1:1 wideband transformer and coaxial RF connectors. Reference application notes for schematic and layout guidelines. The transmitter encodes the data using CMI line coding and shapes an analog signal to meet the appropriate ITU-T G.703 template. The CMI outputs are tri-stated during transmit disable and transmit power-down for redundancy applications and powersavings. Note: To avoid reflections causing unwanted board noise, it’s recommended to power-down unused transmit ports that are not terminated with cable to an Rx input port. When the CMI pin is low, the chip is in Fiber (NRZ pass-through) mode and interfaces directly to an optical transceiver module. The ECLxP/N pins are internally biased and output NRZ data at LVPECL levels. The CMI driver, encoder and decoder are disabled in Fiber (NRZ) mode. Clock Synthesizer The transmit clock synthesizer is a low-jitter DLL that generates a 278.528/311.04 MHz clock for the CMI encoder. It is also used in both the receive and transmit sides for clock and data recovery. This 2x line rate clock is also available at the TXCKxP/N pins for downstream synchronization or system debug. Transmit Backplane Equalizer An optional fixed LVPECL equalizer is integrated in the transmit path for architectures that use LIUs on active interface cards. The fixed equalizer can compensate for up to 1.5m of FR4 trace and can be enabled by the TXOUT1 pin or TXEQ bit as follows: TXOUT1 pin Low Float TXEQ bit 1 0 Tx Equalizer Enabled Disabled SIxDP/N SIxCKP/N PIxCK PIx[3:0]D PTOxCK POWER-DOWN FUNCTION Power-down controls are provided to allow the 78P2352 to be shut off. Transmit and receive power-down can be set independently through SW control. Total power-down is achieved by powering down both the transmitter and receiver. Note: The serial interface and configuration registers are not affected by power-down. In HW mode, both transmitters can also be globally powered down using the TXPD control pin. LOOPBACK MODES In SW mode, LLBKx and RLBKx bits in the Signal Control Register are provided to activate the local and remote loopback modes respectively. In HW mode, the LPBKx pins can be used to activate local and remote analog loopback modes as shown in the table below. LPBK pin Low Float Analog Loopback Mode Normal operation Remote (analog) Loopback: Recovered receive clock and data looped back directly to the transmit driver. The CMI decoder and most of transmit path is bypassed. Local (analog) Loopback: Transmit clock and data looped back to receiver at the analog media interface. Lock Detect Tx CDR EACH CHANNEL: Tx ECLxP/N High FIFO CMI Encoder TXxCKP/N CMIxP/N PMOD, SMOD[1:0], PAR RLBK SOxCKP/N SOxDP/N POx[3:0]D POxCK CMI Decoder Rx CDR Lock Detect CMI EACH CHANNEL: Rx Adaptive Eq. RXxP/N LOS Detect LLBK Figure 6: Local (Analog) Loopback Transmit Loss of Lock In transmit modes using the integrated CDR, the 78P2352 will declare a loss of lock condition when there is no valid signal detected at the SIxDP/N data inputs. Note: The Tx LOL indicator is invalid and undefined when the parallel (nibble) interface is selected. Lock Detect SIxDP/N SIxCKP/N PIxCK PIx[3:0]D PTOxCK Tx CDR EACH CHANNEL: Tx ECLxP/N FIFO CMI Encoder TXxCKP/N CMIxP/N PMOD, SMOD[1:0], PAR RLBK SOxCKP/N SOxDP/N POx[3:0]D POxCK CMI Decoder Rx CDR Lock Detect CMI EACH CHANNEL: Rx Adaptive Eq. RXxP/N LOS Detect LLBK Figure 7: Remote (Analog) Loopback Page: 7 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU In SW mode only, a Full Remote (digital) Loopback bit FLBK is also available in the Advanced Tx Control register. This loopback exercises the entire Rx and Tx paths of the 78P2352 including the Tx clock recovery unit. As such, the user must enable either Serial Plesiochronous or Serial Loop-timing transmit modes to utilize the Full Remote (digital) Loopback. Lock Detect SIxDP/N SIxCKP/N PIxCK PIx[3:0]D PTOxCK Tx CDR EACH CHANNEL: Tx ECLxP/N SERIAL CONTROL INTERFACE The serial port controlled registers allows a generic controller to interface with the 78P2352. It is used for mode settings, diagnostics and test, retrieval of status and performance information, and for on-chip fuse trimming during production test. The SPSL pin must be high in order to use the serial port. The serial interface consists of four pins: Serial Port Enable (SEN_CMI), Serial Clock (SCK_MON), Serial Data In (SDI_PAR), and Serial Data Out (SDO_E4). The SEN_CMI pin initiates the read and write operations. It can also be used to select a particular device allowing SCK_MON, SDI_PAR and SDO_E4 to be bussed together. SCK_MON is the clock input that times the data on SDI_PAR and SDO_E4. Data on SDI_PAR is latched in on the rising-edge of SCK_MON, and data on SDO_E4 is clocked out using the falling edge of SCK_MON. SDI_PAR is used to insert mode, address, and register data into the chip. Address and Data information are input least significant bit (LSB) first. The mode and address bit assignment and register table are shown in the following section. SDO_E4 is a tri-state capable output. It is used to output register data during a read operation. SDO_E4 output is normally high impedance, and is enabled only during the duration when register data is being clocked out. Read data is clocked out least significant bit (LSB) first. If SDI_PAR coming out of the micro-controller chip is also tri-state capable, SDI_PAR and SDO_E4 can be connected together to simplify connections. The maximum clock frequency for register access is 20MHz. PROGRAMMABLE INTERRUPTS In addition to the receiver LOS and LOL status pins, the 78P2352 provides a programmable interrupt for each transmitter. In HW control mode, the default events that trigger the Tx interrupt is a transmit Loss of Lock (TXLOL) or FIFO error (FERR). FIFO CMI Encoder TXxCKP/N CMIxP/N PMOD, SMOD[1:0], PAR RLBK SOxCKP/N SOxDP/N POx[3:0]D POxCK CMI Decoder Rx CDR Lock Detect CMI EACH CHANNEL: Rx Adaptive Eq. RXxP/N LOS Detect LLBK Figure 8: Remote (Digital) Loopback INTERNAL POWER-ON RESET Power-On Reset (POR) function is provided on chip. Roughly 50µs after Vcc reaches 2.4V at power up, a reset pulse is internally generated. This resets all registers to their default values as well as all state machines within the transceiver to known initial values. The reset signal is also brought out to the PORB pin. The PORB pin is a special function analog pin that allows for the following: • • • Override the internal POR signal by driving in an external active low reset signal; Use the internally generated POR signal to trigger other resets; Add external capacitor to slow down the release of power-on reset (approximately 8µs per nF added). NOTE: Do not pull-up the PORB pin to Vcc or drive this pin high during power-up. This will prevent the internal reset generator from resetting the entire chip and may result in errors. Page: 8 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU REGISTER DESCRIPTION REGISTER ADDRESSING Address Bits Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Sub-Address PA[0] SA[2] SA[1] SA[0] Bit 1 Bit 0 Read/ Write R/W* Port Address Assignment PA[3] PA[2] PA[1] REGISTER TABLE a) PA[3:0] = 0 : Global Registers Sub Addr 0 1 2 Reg. Name MSCR (R/W) INTC (R/W) -(R/W) Description Master Control Interrupt Control Reserved Bit 7 E4 INPOL - Bit 6 - - - Bit 5 PAR - - Bit 4 CKSL[1] - - Bit 3 CKSL[0] - - Bit 2 - - - Bit 1 - MTLOL - Bit 0 SRST MFERR - b) PA[3:0] = 1, 2 : Port-Specific Registers Sub Addr 0 1 2 3 4 5 6-7 Reg. Name MDCR (R/W) SGCR (R/W) ACR1 (R/W) ACR0 (R/W) MCR2 (R/W) STAT (R/C) -Description Mode Control Signal Control Advanced Tx Control 1 Advanced Tx Control 0 Mode Control 2 Status Monitor Reserved Bit 7 PDTX TCMIINV - - CMI - -Bit 6 PDRX RCMIINV Bit 5 PMODE LOLOR - - - - -Bit 4 Bit 3 Bit 2 MON RCLKP - BST[1] - - -Bit 1 - TCLKP TPK BST[0] - TXLOL -Bit 0 - FRST TXEQ FLBK - FERR -- - - - - -- SMOD[1] SMOD[0] RLBK LLBK -- -- -- RXLOS RXLOL --- Page: 9 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU REGISTER DESCRIPTION (CONTINUED) LEGEND TYPE R/O R/C DESCRIPTION Read only Read and Clear TYPE R/W DESCRIPTION Read or Write GLOBAL REGISTERS ADDRESS 0-0: MASTER CONTROL REGISTER BIT NAME TYPE DFLT VALUE DESCRIPTION Line Rate Selection: Selects the line rate of all channels as well as the input clock frequency at the CKREFP/N pins. 0: OC-3, STS-3, STM-1 (155.52MHz) 1: E4 (139.264MHz) Unused Serial/Parallel Interface Selection: Selects the interface to the framer. 0: Serial LVPECL 1: 4-bit Parallel CMOS Reference Clock Frequency Selection: Selects the reference clock frequency input at CKREFP/N pins. 11: 155.52MHz / 139.264MHz (differential LVPECL) 10: 77.76MHz / NA (single-ended CMOS) 00: 19.44MHz / 17.408MHz (single-ended CMOS) Secondary values correspond to E4 frequencies. Default values depend on the CKSL pin selection upon reset. Reserved. Register Soft-Reset: When this bit is set, all registers are reset to their default values. This register bit is self-clearing. 7 E4 R/W 0 6 -- R/W 0 5 PAR R/W 0 4:3 CKSL [1:0] R/W XX 2:1 0 -SRST R/W R/W X0 0 Page: 10 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU REGISTER DESCRIPTION (CONTINUED) ADDRESS 0-1: INTERRUPT CONTROL REGISTER This register selects the events that would cause the interrupt pins to be activated. User may set as many bits as required. BIT NAME TYPE DFLT VALUE 0 01000 DESCRIPTION Interrupt Pin Polarity Selection: 7 6:2 INPOL -R/W R/W 0 : Interrupt output is active-low (default) 1 : Interrupt output is active-high Reserved for future use TXLOL Error Mask (active low): Gates the TXLOL register bit to the INTTXxB interrupt pin. 0: Mask 1: Pass FIERR Error Mask (active low): Gates the respective FIERR register bit to the INTTXxB interrupt pin. 0: Mask 1: Pass ADDRESS 0-2: RESERVED BIT 7:0 NAME -TYPE R/W DFLT VALUE XXXXXXX0 DESCRIPTION Reserved. 1 MTLOL R/W 1 0 MFERR R/W 1 Page: 11 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU REGISTER DESCRIPTION (CONTINUED) PORT-SPECIFIC REGISTERS For PA[3:0] = 1-2 = N only. Accessing a register with port address greater than 2 constitutes an invalid command, and the read/write operation will be ignored. ADDRESS N-0: MODE CONTROL REGISTER BIT 7 NAME PDTX TYPE R/W DFLT VALUE 0 DESCRIPTION Transmitter Power-Down: 0 : Normal Operation 1 : Power-Down. CMI Transmit output is tri-stated. Receiver Power-Down: 0 : Normal Operation 1 : Power-Down Parallel Mode Interface Selection: When PAR=0, PMODE is invalid and defaults to logic ‘1’; When PAR=1, (Master Control Register: bit 5), PMODE selects the source of the transmit parallel clock, either taken from the framer externally or generated internally. Default value is determined by CKMODE pin setting upon power up or reset. 0: Slave Timing. PIxCK clock input to the transmitter 1: Master Timing. PTOxCK clock output from the transmitter Serial Mode Interface Selection: When PAR=0 (Master Control Register: bit 5), SMOD[1:0] configures the transmitter’s system interface. Default values determined by CKMODE pin setting upon power up or reset. SMOD[1] SMOD[0] 0 0 Synchronous clock and data are passed through a FIFO. The CDR is bypassed. 1 0 Synchronous data is passed through the CDR and then through the FIFO. 0 1 Plesiochronous data is passed through the CDR to recover a clock. FIFO is bypassed because the data is not synchronous with the reference clock. 1 1 Loop Timing Mode Enable: The recovered receive clock is used as the reference for the transmit DLL and FIFO. When PAR=1 (Master Control Regsiter: bit 5), setting SMOD[1:0] = 11 will enable Loop Timing Mode. Default values are determined by CKMODE pin setting upon power up or reset as follows: CKMODE Low SMOD[1:0] default = 00 (no effect) CKMODE Float SMOD[1:0] default = 11 (loop-timing enable) CKMODE High SMOD[1:0] default = 01 (no effect) Receive Monitor Mode Enable: 0: Normal Operation 1: Adds 20dB of flat gain to the receive signal before equalization NOTE: Monitor mode is only available in CMI mode. Reserved 2006 Teridian Semiconductor Corporation 6 PDRX R/W 0 5 PMODE R/W X 4 SMOD[1] R/W X 3 SMOD[0] R/W X 2 1:0 MON -- R/W R/W 0 00 Page: 12 of 42 Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU REGISTER DESCRIPTION (CONTINUED) ADDRESS N-1: SIGNAL CONTROL REGISTER BIT NAME TYPE DFLT VALUE DESCRIPTION Transmit CMI Inversion: This bit will flip the polarity of the transmit CMI data outputs at CMIxP/N. For debug use only. 0: Normal 1: Invert Receive CMI Inversion: This bit will flip the polarity of the receive CMI data inputs at RXxP/N. For debug use only. 0: Normal 1: Invert Receive Loss of Lock/Signal Override: When high, the RXLOL and RXLOS signals will always remain low. 0: Normal 1: Forces LOS and LOL outputs to be low and resets counters NOTE: For reliable operation of the Rx LOL detection circuitry, one must manually reset the LOL counter by toggling this bit upon power-up or initialization. Analog Loopback Selection: RLBK LLBK 0 0 Normal operation 1 0 Remote Loopback Enable: Recovered receive data is looped back to the transmit driver for retransmission. 0 1 Local Loopback Enable: The transmit data is looped back and used as the input to the receiver. Receive Clock Inversion Select: This bit will invert the receive output clock. 0: Normal. Data clocked out on falling edge of receive clock. 1: Invert. Data clocked out on the rising edge of receive clock. Transmit Clock Inversion Select: This bit will invert the transmit input system clock. 0: Normal. Data is clocked in on rising edge of the transmit clock. 1: Invert. Data is clocked in on the falling edge of the transmit clock. FIFO Reset: 0: Normal operation 1: Reset FIFO pointers to default locations. This reset should be initiated anytime the transmitter or IC powers up to ensure the FIFO is centered after internal VCO clocks and external transmit clocks are stable. *Not required for Plesiochronous Serial Mode 7 TCMIINV R/W 0 6 RCMIINV R/W 0 5 LOLOR R/W 0 4 RLBK R/W 0 3 LLBK R/W 0 2 RCLKP R/W 0 1 TCLKP R/W 0 0 FRST R/W 0 Page: 13 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU REGISTER DESCRIPTION (CONTINUED) ADDRESS N-2: ADVANCED TRANSMIT CONTROL REGISTER 1 BIT 7:1 NAME -TYPE R/W DFLT VALUE 0000000 DESCRIPTION Reserved. Transmit Fixed Equalizer Enable: When enabled, compensates for between 0.75m and 1.5m of FR4 trace to the serial LVPECL data inputs SIxDP/N 0: Normal Operation 1: Enable equalizer 0 TXEQ R/W 0 ADDRESS N-3: ADVANCED TRANSMIT CONTROL REGISTER 0 BIT 7:3 NAME -TYPE R/W DFLT VALUE 10101 DESCRIPTION Reserved. Transmit Driver Amplitude Boost: Adds roughly 5% or 10% of boost to the CMI output. Limits not tested during production test. 00 : Normal amplitude 01 : 5% boost 10 : Reserved 11 : 10% boost Full Remote (digital) Loopback Enable: When enabled the recovered receive data is decoded and looped back to the transmit clock recovery unit exercising the entire receive and transmit paths. NOTE: Must be used in conjunction with Serial Plesiochronous Mode or Serial Loop-Timing Mode. 2:1 BST[1:0] R/W 00 0 FLBK R/W 0 ADDRESS N-4: MODE CONTROL REGISTER 2 BIT NAME TYPE DFLT VALUE DESCRIPTION Line Interface Mode Selection: 0: Optical fiber (LVPECL, NRZ). CMI ENDEC and line driver are disabled. Use RXxP/N and ECLxP/N pins for line interface. 1: Coaxial cable (CMI encoded). CMI ENDEC enabled. Optical (NRZ) interface disabled. Use RXxP/N and CMIxP/N pins for line interface. Reserved. 7 CMI R/W 1 6:0 -- R/W XX00000 Page: 14 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU REGISTER DESCRIPTION (continued) ADDRESS N-5: STATUS MONITOR REGISTER BIT 7:5 4 NAME -RXLOS TYPE R/C R/C DFLT VALUE XXX X DESCRIPTION Reserved. Receive Loss of Signal Indication: 0: Normal operation 1: Loss of signal condition detected Receive Loss of Lock Indication: This status bit is only defined during a valid input signal at RxP/N or when RXLOS=0 0: Normal operation 1: Recovered receive clock frequency differs from the reference by more than +/- 100ppm. Unused Transmit Loss of Lock Indication: This status bit is only defined and valid when using one of the serial transmit modes utilizing the Tx CDR. 0: Valid transmit input signal detected at SIxDP/N 1: No valid signal detected at SIxDP/N Transmit FIFO Error Indication: This bit is set whenever the internal FERR signal is asserted, indicating that the FIFO is operating at its depth limit. It is reset to 0 when the FRST pin is asserted. 0: Normal operation 1: Transmit FIFO phase error 3 RXLOL R/C X 2 -- R/C X 1 TXLOL R/C X 0 FERR R/C X ADDRESS N-6, N-7: RESERVED BIT 7:0 NAME RSVD TYPE R/O DFLT VALUE 0 DESCRIPTION Reserved for test. Page: 15 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU PIN DESCRIPTION LEGEND TYPE A CIT CI CIU CID CIS PI DESCRIPTION Analog Pin (Tie unused pins to ground) TYPE PO CO COZ OD S G DESCRIPTION LVPECL-Compatible Differential Output (Tie unused pins to supply or leave floating) 3-State CMOS Digital Input CMOS Digital Input (Tie unused pins to ground) CMOS Digital Output (Leave unused pins floating) CMOS Tristate Digital Output (Leave unused pins floating) CMOS Digital Input w/ Pull-up CMOS Digital Input w/ Pull-down CMOS Schmitt Trigger Input (Tie unused pins to ground) Open-drain Digital Output (Leave unused pins floating) Supply Ground LVPECL-Compatible Differential Input (Tie unused pins to ground) TRANSMITTER PINS NAME PIx0D PIx1D PIx2D PIx3D PIxCK PIN 31, 66 32, 65 33, 64 34, 63 30, 67 TYPE DESCRIPTION Transmit (Parallel Mode) Data Input: Four-bit CMOS parallel (nibble) inputs. Data is latched in on the rising edge (default) of the transmit parallel clock and serialized with the MSB (PIx3D) transmitted first. Transmit (Parallel Mode) Clock Input: A 34.816 MHz (E4) or 38.88 MHz (STM1) CMOS clock input that must be source synchronous with the reference clock supplied at the CKREFP/N pins. Used only in Slave Parallel Mode and Loop-timing Parallel Mode. Transmit (Parallel Mode) Clock Output: A 34.816 MHz (E4) or 38.88 MHz (STM1) CMOS clock output that is intended to latch in synchronous parallel data. Active during reset. Used only in Master Parallel Mode (output disabled in all other transmit modes). Transmit (Serial Mode) Data Input: Differential NRZ data input. See Transmitter Operation section for more info on different clocking/timing modes. Transmit (Serial Mode) Clock Input: A 155.52MHz synchronous differential input clock used to clock in the serial NRZ data. By default, data is clocked in on the rising edge of SIxCKP. Transmit (Serial Mode) CMI Data Output: A CMI encoded data signal conforming to the relevant ITU-T G.703 pulse templates when properly terminated and transformer coupled to 75Ω cable. Outputs are tri-stated when transmitter is disabled. Active, but undefined during reset. Transmit (Serial Mode) Clock Output: A 2x line rate LVPECL clock output used to clock out the transmit CMI data. Used for diagnostics or far end re-timing. Active during reset. Transmit (Serial Mode) LVPECL Data Output: Transmit NRZ data outputs used for interfacing with optical transceiver modules when in Fiber (NRZ) mode. 2006 Teridian Semiconductor Corporation Rev. 2.4 CI CIS PTOxCK 35, 62 CO SIxDP SIxDN SIxCKP SIxCKN 10, 87 11, 86 7, 90 8, 89 PI PI CMIxP CMIxN 121, 104 122, 103 A TXxCKP TXxCKN ECLxP ECLxN Page: 16 of 42 124, 101 125, 100 127, 98 128, 97 PO PO 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU PIN DESCRIPTION (CONTINUED) RECEIVER PINS NAME POx0D POx1D POx2D POx3D PIN 46, 51 45, 52 42, 55 41, 56 TYPE DESCRIPTION Receive (Parallel Mode) Data Output: Recovered receive data deserialized into four-bit CMOS parallel (nibble) outputs. The MSB (POx3D) is received first. Active, but undefined during reset. Note: During Loss of Signal conditions, data outputs are held low. Receive (Parallel Mode) Clock Output: A 34.816 MHz (E4) or 38.88 MHz (STM1) CMOS clock output generated by dividing down the recovered receive clock. By default, receive data is clocked out on the falling edge. Active during reset. Note: During Loss of Signal conditions, the clock will remain on the last divided down phase selection of the Rx DLL and output a steady clock. Receive (Serial Mode) Data Output: Recovered receive serial NRZ data at LVPECL levels. Active, but undefined during reset. Note: During Loss of Signal conditions, data outputs are held at logic 0. Receive (Serial Mode) Clock Output: Recovered receive serial clock. By default, recovered serial NRZ data is clocked out the falling edge of SOxCKP. Active during reset. Note: During Loss of Signal conditions, the clock will remain on the last phase selection of the Rx DLL and output a steady clock. Receiver CMI or LVPECL Input: The input is either transformer-coupled to coaxial cable for CMI data or ACcoupled at LVPECL levels to an optical transceiver module for NRZ data. CO POxCK 38, 59 CO SOxDP SOxDN 28, 69 29, 68 PO SOxCKP SOxCKN 25, 72 26, 71 PO RXxP RXxN 118, 107 119, 106 A/ PI Page: 17 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU PIN DESCRIPTION (CONTINUED) REFERENCE AND STATUS PINS Note: The LOSx, LOLx, and INTxXxB pins are configurable at final test (default open-drain outputs). If CMOS level outputs are required, please refer to alternate 70Pxxxx ordering numbers at the end of the data sheet. NAME PIN TYPE DESCRIPTION Reference Clock Input: A required reference clock input used for clock/data recovery and frequency synthesizer. Options include : CKREFP CKREFN 111 110 PI/ CI • 139.264 MHz (E4) or 155.52 MHz (STM1) differential LVPECL clock input at CKREFP/N • 17.408 MHz (E4), 19.44 MHz (STM1), or 77.78 MHz (STM1) singleended CMOS clock input at CKREFP. Tie CKREFN to ground when unused. LOS1 LOS2 LOL1 LOL2 80 19 79 20 OD/ CO OD/ CO Receive Loss of Signal (active-high): See Receiver Loss of Signal description for conditions. Receive Loss of Lock (active-high): This condition is met when the recovered clock frequency differs from the reference clock frequency by more than +/- 100ppm. Transmitter Fault Interrupt Flag (active low): When a transmitter error event occurs (as defined in the Interrupt Control Register Description), the INTTXxB pin will change state to indicate an interrupt. The interrupt is cleared by a read to the STAT Register, an issue of a FRSTx FIFO reset pulse (if the FIERRx signal caused the interrupt), or when the TXLOL register bit transitions from high to low. Note: The default interrupt condition is a loss of lock in the transmitter CDR. Receiver Fault Interrupt Flag (active low): Reserved for future use. Power-On Reset (active low): See Power-On Reset description on use of this pin. INTTX1B INTTX2B 88 9 OD/ CO INTRX1B INTRX2B PORB 70 27 83 OD/ CO A Page: 18 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU PIN DESCRIPTION (CONTINUED) CONTROL PINS NAME PIN TYPE DESCRIPTION FIFO Phase-Initialization Control: When asserted, the transmit FIFO pointers are reset to the respective “centered” states. Also resets the FIERR interrupt bit. De-assertion edge of FRSTx will resume FIFO operation. • FRST 78 CIT • Low: Channel 1 FRST assertion Float: Normal operation • High: Channel 2 FRST assertion Because the internal VCO clock and off-chip transmit clocks may not be stable during transmit power-up, it is recommended to always reset the FIFOs after powering up the IC or the transmitter. Not valid during Plesiochronous Serial Mode. Analog Loopback Selection: • LPBKx 17, 18 CIT • • Low: Normal operation Float: Remote Loopback Enable: Recovered receive data and clock are looped back to the transmitter for retransmission. High: Local Loopback Enable: The serial transmit data is looped back and used as the input to the receiver. Clock Mode Selection: Selects the method of inputting transmit data into the chip. See TRANSMITTER OPERATION section for more information. In PARALLEL mode (SDI_PAR high): • • CKMODE 15 CIT Low: Parallel transmit clock is input to the 78P2352. Float: Parallel transmit clock is input to the 78P2352. Loop-timing mode enabled. • High: Parallel transmit clock is output from the 78P2352 In SERIAL mode (SDI_PAR low): • • • Low: Reference clock is synchronous to transmit clock and data. Data is clocked in with SIxCKP/N and passed through a FIFO Float: Reference clock is synchronous to transmit data. Clock is recovered with a CDR and data is passed through a FIFO High: Reference clock is plesiochronous to transmit data. Clock is recovered with a CDR and the FIFO is bypassed Page: 19 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU PIN DESCRIPTION (CONTINUED) CONTROL PINS (continued) NAME PIN TYPE DESCRIPTION Advanced Tx Control 1: Low: Enables fixed LVPECL equalizer at the transmit inputs SIDP/N for FR4 trace lengths up to 1.5m. Float: Normal operation High: Normal operation Advanced Tx Control 0: Low: Nominal amplitude Float: 5% amplitude boost High: 10% amplitude boost Transmitter Power Down: When high, powers down and tr-states the transmitt driver on both channels. Serial Port Selection: When high, chip is software controlled through the serial port. Reference Clock Frequency Selection: Selects the reference frequency that is supplied at the CKREFP/N pins. Its level is read in only at power-up or on the rising edge of a reset signal at the PORB pin. • • • Low: 19.44MHz or 17.408MHz Float: 77.76MHz High: 155.52MHz or 139.264MHz TXOUT1 1 CIT TXOUT0 2 CIT TXPD SPSL 14 77 CID CID CKSL 81 CIT Page: 20 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU PIN DESCRIPTION (CONTINUED) SERIAL-PORT PINS NAME PIN TYPE DESCRIPTION [SPSL=1] Serial-Port Enable: High during read and write operations. Low disables the serial port. While SEN is low, SDO remains in high impedance state, and SDI and SCK activities are ignored. [SPSL=0] Medium Select: Low: Fiber (NRZ pass-through) mode High: CMI mode [SPSL=1] Serial Clock: Controls the timing of SDI and SDO. [SPSL=0] Receive Monitor Mode Enable: When high, adds 20dB of flat gain to the incoming signal of both channels before equalization. NOTE: Channel specific monitor modes can be enabled through the serial port. Rx Monitor Mode is only available in CMI mode [SPSL=1] Serial Data Input: Inputs mode and address information. Also inputs register data during a Write operation. Both address and data are input least significant bit first. [SPSL=0] Data Width Select: Selects 4 bit parallel transmit modes (input high) or serial transmit modes (input low) [SPSL=1] Serial Data Output: Outputs register information during a Read operation. Data is output least significant bit first [SPSL=0] Rate Select: Selects E4 operation (input high) or STM1/STS3 operation (input low) SEN_CMI 95 CIU SCK_MON 96 CIS SDI_PAR 94 CI SDO_E4 93 COZ/ CI POWER AND GROUND PINS It is recommended that all supply pins be connected to a single power supply plane and all ground pins be connected to a single ground plane. See application note for decoupling guidelines. NAME VCC VDD GND VSS TGND PIN 5, 12, 21, 74, 85, 92, 99, 105, 109, 116, 120, 126 23, 37, 40, 44, 48, 49, 53, 57, 60 6, 13, 16, 22, 73, 84, 91, 102, 108, 112, 113, 114, 115, 117, 123 24, 36, 39, 43, 47, 50, 54, 58, 61 82 TYPE S S G G G DESCRIPTION Power Supply CMOS I/O Driver Supply Ground CMOS I/O Driver Ground Trim Ground Used during production test. Connect directly to ground. Do not decouple to supply or PORB. Rev. 2.4 Page: 21 of 42 2006 Teridian Semiconductor Corporation 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS Operation beyond these limits may permanently damage the device. PARAMETER Supply Voltage (Vdd) Storage Temperature Junction Temperature Pin Voltage (CMIxP,CMIxN) Pin Voltage (all other pins) Pin Current RATING -0.5 to 4.0 VDC -65 to 150 °C -40 to 150 °C Vdd + 1.5 VDC -0.3 to (Vdd+0.6) VDC ±100 mA RECOMMENDED OPERATING CONDITIONS Unless otherwise noted all specifications are valid over these temperatures and supply voltage ranges. PARAMETER DC Voltage Supply (Vdd) Ambient Operating Temperature Junction Temperature RATING 3.15 to 3.45 VDC -40 to 85 °C -40 to 125 °C DC CHARACTERISTICS: PARAMETER Total Supply Current (CMI) (including transmitter current through transformer) Total Supply Current (NRZ) SYMBOL Idd CONDITIONS STM-1 mode; CMI mode; Max. cable length STM-1 mode; Fiber (NRZ) mode Transmitter disabled; STM-1 mode; CMI mode; Max. cable length STM-1 mode; CMI mode; Max. cable length PDTX = 1, PDRX = 1 MIN NOM 325 MAX 350 UNIT mA Idde 290 310 mA Receive-only Supply Current Iddr 190 205 mA Supply Current per Port (CMI) (including transmitter current through transformer) Power down Current Iddx 160 180 mA Iddq 7 10 mA Page: 22 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) ANALOG PINS CHARACTERISTICS: The following table is provided for informative purpose only. Not tested in production. PARAMETER RXxP and RXxN Common-Mode Bias Voltage RXxP and RXxN Differential Input Impedance Analog Input/Output Capacitance PORB Input Impedance DIGITAL I/O CHARACTERISTICS: Pins of type CI, CIU, CID: PARAMETER Input Voltage Low Input Voltage High Input Current Pull-up Resistance Pull-down Resistance Input Capacitance Pins of type CIT: PARAMETER Input Voltage Low Input Voltage High Minimum impedance to be considered as “float” state Pins of type CIS: PARAMETER Low-to-High Threshold High-to-Low Threshold Input Current Input Capacitance SYMBOL Vt+ VtIil, Iih Cin CONDITIONS MIN 1.3 0.8 -1 8 NOM MAX 1.7 1.2 1 UNIT V V µA pF SYMBOL Vtil Vtih Rtiz Vcc-0.6 30 CONDITIONS MIN NOM MAX 0.4 UNIT V V kΩ SYMBOL Vil Vih Iil, Iih Rpu Rpd Cin Type CIU only Type CID only CONDITIONS Type CI, CID only Type CIU only 2.0 -1 53 40 0 70 58 8 1 113 120 MIN NOM MAX 0.8 0.4 UNIT V V µA kΩ kΩ pF SYMBOL Vblin Rilin Cin -CONDITIONS Ground Reference MIN 1.9 NOM 2.1 20 8 5 MAX 2.6 UNIT V kΩ pF kΩ Page: 23 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) Pins of type CO and COZ: PARAMETER Output Voltage Low Output Voltage High Output Transition Time Effective Source Impedance Tri-state Output Leakage Current Pins of type PO: PARAMETER Signal Swing Common Mode Level Effective Source Impedance Rise Time Fall Time Pins of type PI: PARAMETER Signal Swing Common Mode Level Pins of type OD: PARAMETER Output Voltage Low Pull-down Leakage Current Pull-up Resistor SYMBOL Vol Ipd Rpu CONDITIONS Iol = 8mA Logic high output 4.7 MIN NOM MAX 0.4 1 10 UNIT V µA kΩ SYMBOL Vpki Vcm CONDITIONS Vdd referenced MIN 0.3 -1.6 NOM -1.2 MAX -0.8 UNIT V V SYMBOL Vpk Vcm Reff Tr Tf 10-90% 10-90% CONDITIONS TXxCKP/N pins Vdd referenced MIN 0.5 0.35 -1.55 -1.2 20 0.8 0.8 1.2 1.2 NOM 0.8 MAX 1.1 0.95 -1.1 UNIT V V Ω ns ns SYMBOL Vol Voh Tt Rscr Iz Type COZ only -1 CONDITIONS Iol = 8mA Ioh = -8mA CL = 20pF, 10-90% 30 1 2.4 2 MIN NOM MAX 0.4 UNIT V V ns Ω µA Page: 24 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) SERIAL-PORT TIMING CHARACTERISTICS: PARAMETER SDI to SCK setup time SDI to SCK hold time SCK to SDO propagation delay SCK Frequency SYMBOL tsu th tprop SCK CONDITION MIN 4 4 10 20 TYP MAX UNIT ns ns ns MHz CS SCK tsu th tsu th SDI SDO X 1 SA0 SA1 SA2 PA0 PA1 PA2 PA3 tprop X or Z Z D0 D1 D2 D3 D4 D5 D6 D7 Z Figure 9: Read Operation CS SCK tsu th tsu th SDI SDO X 0 SA0 SA1 SA2 PA0 PA1 PA2 PA3 D0 D1 D2 D3 D4 D5 D6 D7 X Z Figure 10: Write Operation Page: 25 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) TRANSMITTER TIMING CHARACTERISTICS: PARAMETER Clock Duty Cycle Setup Time Hold Time Setup Time Hold Time SYMBOL TTCF/TTC TPS TPH TSS TSH CONDITIONS PTOxCK Parallel mode Parallel mode Serial mode Serial mode MIN 40 4 4 2 2 NOM MAX 60 UNIT % ns ns ns ns TIMING DIAGRAM: Transmitter Waveforms SIxCKN SIxCKP SIxDP SIxDN TSS TSH PIxCK PIxD TPS TPH TRC = 25.72ns TRCF = 12.86ns PTOxCK PIxD TPS TTCT TPH Page: 26 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) REFERENCE CLOCK CHARACTERISTICS: PARAMETER CKREF Duty Cycle SYMBOL -Synchronous mode; E4 Synchronous mode; STM1 Plesiochronous or Loop-timing mode. (see Note 1) CONDITIONS MIN 40 -15 -20 -75 NOM MAX 60 +15 +20 +75 UNIT % CKREF Frequency Stability -- ppm Note 1: In Plesiochronous mode, the transmit clock/data source (i.e. framer/system reference clock) must still be of +/-20ppm quality (+/-15ppm for E4) in order to meet the ITU-T (or Telcordia) bit rate requirements. RECEIVER TIMING CHARACTERISTICS: PARAMETER RCLK Duty Cycle Clock to Q SYMBOL TRCF/TRC RSCQ RPCQ Serial mode Parallel mode CONDITIONS MIN 40 0 -1 NOM MAX 60 1 2 UNIT % ns TIMING DIAGRAM: Receive Waveforms TRC = 6.43ns TRCF = 3.215ns SOxCKN SOxCKP SOxDP SOxDN RSCQ TRCT TRC = 25.72ns TRCF = 12.86ns POxCK POxD RPCQ TRCT Page: 27 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) TRANSMITTER SPECIFICATIONS FOR CMI INTERFACE Bit Rate: 139.264Mbps ± 15ppm or 155.52Mbps ± 20ppm Code: Coded Mark Inversion (CMI) Relevant Specification: ITU-T G.703, Telcordia GR-253, ANSI T1.102 With the coaxial output port driving a 75Ω load, the output pulses conform to the templates in Figures 11, 12, 13, and 14. These specifications are tested during production test. Consult application note for reference schematic, layout guidelines, and recommended transformers. PARAMETER Peak-to-peak Output Voltage (Fuse-trimmed to nominal target at final test) Rise/ Fall Time CONDITION Template, steady state 10-90% Negative Transitions Transition Timing Tolerance Positive Transitions at Interval Boundaries Positive Transitions at midinterval With respect to CKREF -0.1 -0.5 -0.35 0 MIN 0.9 NOM 1.05 MAX 1.1 2 0.1 0.5 0.35 0 ppm ns UNIT V ns Transmit clock frequency stability (PIxCK or SIxCKP/N ) The following specifications are not tested during production test. They are included for information only. PARAMETER Output Impedance Return Loss CONDITION Driver is open drain 7MHz to 240MHz 15 MIN NOM 1 8 MAX UNIT MΩ pF dB Page: 28 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) V 0.60 0.55 0.50 0.45 0.40 1ns 0.1ns 0 .1ns 0.35ns T = 7.18ns (Note 1) (Note 1) N ominal Pulse 1.795 ns 1ns 0.1ns 0.35ns 0 .1ns 1.795 ns 1ns 0.05 -0.05 Nominal Z ero Level (Note 2) -0.40 -0.45 -0.50 -0.55 -0.60 1ns 1.795 ns (Note 1) 1ns 1.795 ns 1ns (Note 1) Note 1 – The maximum “steady state” amplitude should not exceed the 0.55V limit. Overshoots and other transients are permitted to fall into the shaded area bounded by the amplitude levels 0.55V and 0.6V, provided that they do not exceed the steady state level by more than 0.05V. Note 2 – For all measurements using these masks, the signal should be AC coupled, using a capacitor of not less than 0.01 µF, to the input of the oscilloscope used for measurements. The nominal zero level for both masks should be aligned with the oscilloscope trace with no input signal. With the signal then applied, the vertical position of the trace can be adjusted with the objective of meeting the limits of the masks. Any such adjustment should be the same for both masks and should not exceed ±0.05V. This may be checked by removing the input signal again and verifying that the trace lies with ±0.05V of the nominal zero level of the masks. Note 3 – Each pulse in a coded pulse sequence should meet the limits of the relevant mask, irrespective of the state of the preceding or succeeding pulses, with both pulse masks fixed in the same relation to a common timing reference, i.e. with their nominal start and finish edges coincident. The masks allow for HF jitter caused by intersymbol interference in the output stage, but not for jitter present in the timing signal associated with the source of the interface signal. When using an oscilloscope technique to determine pulse compliance with the mask, it is important that successive traces of the pulses overlay in order to suppress the effects of low frequency jitter. This can be accomplished by several techniques [e.g. a) triggering the oscilloscope on the measured waveform or b) providing both the oscilloscope and the pulse output circuits with the same clock signal]. Note 4 – For the purpose of these masks, the rise time and decay time should be measured between –0.4V and 0.4V, and should not exceed 2ns. Figure 11 – Mask of a Pulse corresponding to a binary Zero in E4 mode Page: 29 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) V 0.60 0.55 0.50 0.45 0.40 1ns 0.1ns 0.1ns 0.5ns T = 7.18ns (Note 1) (Note 1) 1ns 0.5ns Nominal Pulse 0.05 -0.05 Nominal Zero Level (Note 2) 3.59ns 1.35ns 1.35ns 3.59ns -0.40 -0.45 -0.50 -0.55 -0.60 1ns 1.795 ns (Note 1) 1ns 1.795 ns Note 1 – The maximum “steady state” amplitude should not exceed the 0.55V limit. Overshoots and other transients are permitted to fall into the shaded area bounded by the amplitude levels 0.55V and 0.6V, provided that they do not exceed the steady state level by more than 0.05V. Note 2 – For all measurements using these masks, the signal should be AC coupled, using a capacitor of not less than 0.01 µF, to the input of the oscilloscope used for measurements. The nominal zero level for both masks should be aligned with the oscilloscope trace with no input signal. With the signal then applied, the vertical position of the trace can be adjusted with the objective of meeting the limits of the masks. Any such adjustment should be the same for both masks and should not exceed ±0.05V. This may be checked by removing the input signal again and verifying that the trace lies with ±0.05V of the nominal zero level of the masks. Note 3 – Each pulse in a coded pulse sequence should meet the limits of the relevant mask, irrespective of the state of the preceding or succeeding pulses, with both pulse masks fixed in the same relation to a common timing reference, i.e. with their nominal start and finish edges coincident. The masks allow for HF jitter caused by intersymbol interference in the output stage, but not for jitter present in the timing signal associated with the source of the interface signal. When using an oscilloscope technique to determine pulse compliance with the mask, it is important that successive traces of the pulses overlay in order to suppress the effects of low frequency jitter. This can be accomplished by several techniques [e.g. a) triggering the oscilloscope on the measured waveform or b) providing both the oscilloscope and the pulse output circuits with the same clock signal]. Note 4 – For the purpose of these masks, the rise time and decay time should be measured between –0.4V and 0.4V, and should not exceed 2ns. Note 5 –The inverse pulse will have the same characteristics, noting that the timing tolerance at the level of the negative and positive transitions are ± 0.1ns and ±0.5ns respectively. Figure 12 – Mask of a Pulse corresponding to a binary One in E4 mode. Page: 30 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) V 0.60 0.55 0.50 0.45 0.40 1ns 0.1ns 0.1ns 0.35ns T = 6.43ns (Note 1) (Note 1) Nominal Pulse 1.608ns 1ns 0.1ns 0.35ns 0.1ns 1.608ns 1ns 0.05 -0.05 Nominal Zero Level (Note 2) -0.40 -0.45 -0.50 -0.55 -0.60 1ns 1.608ns (Note 1) 1ns 1.608ns 1ns (Note 1) Note 1 – The maximum “steady state” amplitude should not exceed the 0.55V limit. Overshoots and other transients are permitted to fall into the shaded area bounded by the amplitude levels 0.55V and 0.6V, provided that they do not exceed the steady state level by more than 0.05V. Note 2 – For all measurements using these masks, the signal should be AC coupled, using a capacitor of not less than 0.01 µF, to the input of the oscilloscope used for measurements. The nominal zero level for both masks should be aligned with the oscilloscope trace with no input signal. With the signal then applied, the vertical position of the trace can be adjusted with the objective of meeting the limits of the masks. Any such adjustment should be the same for both masks and should not exceed ±0.05V. This may be checked by removing the input signal again and verifying that the trace lies with ±0.05V of the nominal zero level of the masks. Note 3 – Each pulse in a coded pulse sequence should meet the limits of the relevant mask, irrespective of the state of the preceding or succeeding pulses, with both pulse masks fixed in the same relation to a common timing reference, i.e. with their nominal start and finish edges coincident. The masks allow for HF jitter caused by intersymbol interference in the output stage, but not for jitter present in the timing signal associated with the source of the interface signal. When using an oscilloscope technique to determine pulse compliance with the mask, it is important that successive traces of the pulses overlay in order to suppress the effects of low frequency jitter. This can be accomplished by several techniques [e.g. a) triggering the oscilloscope on the measured waveform or b) providing both the oscilloscope and the pulse output circuits with the same clock signal]. Note 4 – For the purpose of these masks, the rise time and decay time should be measured between –0.4V and 0.4V, and should not exceed 2ns. Figure 13 – Mask of a Pulse corresponding to a binary Zero in STS-3/STM-1 mode. Page: 31 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) V 0.60 0.55 0.50 0.45 0.40 1ns 0.1ns 0.1ns 0.5ns 6.43ns (Note 1) (Note 1) 1ns 0.5ns Nominal Pulse 0.05 -0.05 Nominal Zero Level (Note 2) 3.215ns 1.2ns 1.2ns 3.215ns -0.40 -0.45 -0.50 -0.55 -0.60 1ns 1.608ns (Note 1) 1ns 1.608ns Note 1 – The maximum “steady state” amplitude should not exceed the 0.55V limit. Overshoots and other transients are permitted to fall into the shaded area bounded by the amplitude levels 0.55V and 0.6V, provided that they do not exceed the steady state level by more than 0.05V. Note 2 – For all measurements using these masks, the signal should be AC coupled, using a capacitor of not less than 0.01 µF, to the input of the oscilloscope used for measurements. The nominal zero level for both masks should be aligned with the oscilloscope trace with no input signal. With the signal then applied, the vertical position of the trace can be adjusted with the objective of meeting the limits of the masks. Any such adjustment should be the same for both masks and should not exceed ±0.05V. This may be checked by removing the input signal again and verifying that the trace lies with ±0.05V of the nominal zero level of the masks. Note 3 – Each pulse in a coded pulse sequence should meet the limits of the relevant mask, irrespective of the state of the preceding or succeeding pulses, with both pulse masks fixed in the same relation to a common timing reference, i.e. with their nominal start and finish edges coincident. The masks allow for HF jitter caused by intersymbol interference in the output stage, but not for jitter present in the timing signal associated with the source of the interface signal. When using an oscilloscope technique to determine pulse compliance with the mask, it is important that successive traces of the pulses overlay in order to suppress the effects of low frequency jitter. This can be accomplished by several techniques [e.g. a) triggering the oscilloscope on the measured waveform or b) providing both the oscilloscope and the pulse output circuits with the same clock signal]. Note 4 – For the purpose of these masks, the rise time and decay time should be measured between –0.4V and 0.4V, and should not exceed 2ns. Note 5 –The inverse pulse will have the same characteristics, noting that the timing tolerance at the level of the negative and positive transitions are ± 0.1ns and ±0.5ns respectively. Figure 14 – Mask of a Pulse corresponding to a binary One in STS-3/STM-1 mode Page: 32 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) TRANSMITTER OUTPUT JITTER The transmit jitter specification ensures compliance with ITU-T G.813, G.823, G.825 and G.958; ANSI T1.1021993 and T1.105.03-1994; and GR-253-CORE for all supported rates. Transmit output jitter is not tested during production test. Jitter Detector Transmitter Output 20dB/decade Measured Jitter Amplitude f1 f2 PARAMETER CONDITION CMI Mode; 200 Hz to 3.5 MHz, measured with respect to CKREF for 60s NRZ (optical) Mode; 12 kHz to 1.3 MHz, measured with respect to CKREF MIN NOM MAX 0.075 UNIT UIpp Transmitter Output Jitter 0.01 UIrms Page: 33 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) RECEIVER SPECIFICATIONS FOR CMI INTERFACE (Transformer-coupled) Consult application note for reference schematic, layout guidelines, and recommended transformers. PARAMETER Peak Differential Input Amplitude, RXxP and RXxN Peak Differential Input Amplitude, RXxP and RXxN Flat-loss Tolerance CONDITION CMI mode; MON=0; 12.7dB of cable loss CMI mode; MON=1; 20dB flat loss w/ 6dB of cable loss CMI mode; MON=0; All valid cable lengths. STM-1 mode; CMI mode; 12.7 dB cable loss a) Normal receive mode b) Remote loopback mode MIN 70 25 -2 TYP MAX 550 80 6 UNIT mVpk mVpk dB Receive Clock Jitter Latency PLL Lock Time Return Loss 5 1 7MHz to 240MHz 15 0.1 0.07 10 10 UIpp UIpp UI µs dB The input signal is assumed compliant with ITU-T G.703 and can be attenuated by the dispersive loss of a cable. The minimum cable loss is 0dB and the maximum is –12.7dB at 78MHz. The “Worst Case” line corresponds to the ITU-T G.703 recommendation. The “Typical” line corresponds to a typical installation referred to in ANSI T1.102-1993. The receiver is tested using the cable model. It is a lumped element approximation of the “Worst Case” line. 30 25 Attenuation (dB) 20 15 10 5 0 1.00E+05 1.00E+06 1.00E+07 Frequency (Hz) Worst Case Typical 1.00E+08 1.00E+09 Figure 15: Typical and worst-case Cable attenuation Page: 34 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) RECEIVER JITTER TOLERANCE The 78P2352 exceeds all relevant jitter tolerance specifications shown in Figures 16, 17. STS-3/OC-3 jitter tolerance specifications are in ANSI T1.105.03-1994 and Telcordia GR-253-CORE. STM-1 (optical) jitter tolerance specifications are in ITU-T G.813, G.825, and G.958. STM-1e (electrical) jitter tolerance specifications are in ITU-T G.825. E4 specifications are found in ITU-T G.823. Receive jitter tolerance is not tested during production test. 100 Electrical (CMI) Interfaces G.825 - STM-1e Tolerance (for 2048 kbps networks) G.825 - STM-1e Tolerance (for 1544 kbps networks) G.823 - E4 Tolerance 10 Jitter Tolerance ( UIpp ) 1 0.1 0.01 1.E+00 10Hz 100Hz 1kHz 10kHz 100kHz 1MHz 10MHz Jitter Frequency Figure 16: Jitter Tolerance - electrical (CMI) interfaces PARAMETER E4 Jitter Tolerance CONDITION 200Hz to 500Hz 500Hz to 10kHz 10kHz to 3.5MHz 10Hz to 19.3Hz 19.3Hz to 500Hz MIN 1.5 NOM 750 f-1 MAX UNIT UIpp µs UIpp UIpp 0.075 38.9 750 f-1 1.5 9800 f-1 0.15 µs UIpp µs UIpp STM-1e Jitter Tolerance 500Hz to 6.5kHz 6.5kHz to 65kHz 65kHz to 1.3MHz Page: 35 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) 100 Optical (NRZ) Interfaces G.813, G.958, T1.105.03, GR-253 STM-1 / STS-3 / OC-3 Tolerance G.825 - STM-1 Tolerance 10 Jitter Tolerance ( UIpp ) 1 0.1 0.01 1.E+00 10Hz 100Hz 1kHz 10kHz 100kHz 1MHz 10MHz Jitter Frequency Figure 17: Jitter Tolerance - optical (NRZ) interfaces PARAMETER CONDITION 10Hz to 19.3Hz 19.3Hz to 68.7Hz MIN 38.9 NOM 750 f-1 MAX UNIT UIpp µs UIpp µs UIpp OC-3/STS-3/STM-1 (optical) Jitter Tolerance 68.7Hz to 6.5kHz 6.5kHz to 65kHz 65kHz to 1.3MHz 1.5 9800 f-1 0.15 Page: 36 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) RECEIVER JITTER TRANSFER FUNCTION The receiver clock recovery loop filter characteristics such that the receiver has the following transfer function. The corner frequency of the Rx DLL is approximately 120 kHz. Receiver jitter transfer function is not tested during production test. 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 1.00E+03 1.00E+04 1.00E+05 1.00E+06 1.00E+07 Figure 18: Jitter Transfer PARAMETER Receiver Jitter transfer function Jitter transfer function roll-off CONDITION below 120 kHz MIN NOM MAX 0.1 UNIT dB dB per decade 20 Page: 37 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU ELECTRICAL SPECIFICATIONS (continued) CMI MODE LOSS OF SIGNAL CONDITION PARAMETER LOS threshold LOS timing CONDITION Combination of cable loss at 78MHz and flat loss MIN -35 10 TYP -19 110 MAX -15 255 UNIT dB UI Nominal value Maximum cable loss 3 dB 15dB Loss of Signal must be cleared Tolerance range LOS can be detected or cleared 35dB Loss of Signal must be declared APPLICATION INFORMATION EXTERNAL COMPONENTS: COMPONENT Receiver Termination Resistor, CMI Mode Transmitter Termination Resistor, CMI Mode (CMI) TRANSFORMER SPECIFICATIONS: COMPONENT Turns Ratio for the Receiver Turns Ratio for the Transmitter (center-tapped) Suggested Manufacturers: Halo, Tamura, MiniCircuits, Belfuse THERMAL INFORMATION: PACKAGE Standard 128-pin JEDEC LQFP (78P2352-IGT) (Recommended) Thernally enhanced Exposed Pad 128-pin JEDEC LQFP (78P2352-IEL) CONDITIONS No forced air; 4-layer JEDEC test board No forced air; 4-layer JEDEC test board; Die attach pad soldered to PCB ΘJA ( ˚C/W) 46 VALUE UNITS 1:1 1:1CT TOLERANCE PIN(S) RXxP RXxN CMIxP CMIxN VALUE 75 75 UNITS Ω Ω TOLERANCE 1% 1% 24.8 SCHEMATICS For reference schematics, layout guidelines, recommended transformer part numbers, etc. please check Teridian Semiconductor's website or contact your local sales representative for the latest application note(s) and/or demo board manuals. Page: 38 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU MECHANICAL SPECIFICATIONS 16.000 +/- 0.200 14.000 +/- 0.100 12.400 REF. 128 1 14.000 +/- 0.100 MAX. EXPOSED PAD AREA 5.00 REF. 13.950 +/- 0.100 MAX. 1.600 1.400 +/- 0.050 0.180 +/- 0.050 0.400 0.100 +/- 0.050 0.600 +/- 0.150 78P2352-IEL 128-pin Exposed Pad JEDEC LQFP (Bottom View) Page: 39 of 42 2006 Teridian Semiconductor Corporation 16.000 +/- 0.200 5.00 REF. Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU MECHANICAL SPECIFICATIONS 15.8 (0.622) 16.2 (0.637) 15.8 (0.622) 16.2 (0.637) Top View 13.8 (0.543) 14.2 (0.559) 0.05 (0.002) 0.15 (0.006) 1.60 Max (0.063) 0.13 (0.005) 0.23 (0.009) 0.40 Typ. . (0.015) 0.60 Typ. (0.024) Side View 78P2352-IGT 128-pin Standard JEDEC LQFP (Top View) Page: 40 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU PACKAGE INFORMATION (Top View) ECL1N ECL1P VCC TX1CKN TX1CKP GND CMI1N CMI1P VCC RX1N RX1P GND VCC GND GND GND GND CKREFP CKREFN VCC GND RX2P RX2N VCC CMI2P CMI2N GND TX2CKP TX2CKN VCC ECL2P ECL2N TXOUT1 TXOUT0 N/C N/C VCC GND SI1CKP SI1CKN INTTX2B SI1DP SI1DN VCC GND TXPD CKMODE GND LPBK1 LPBK2 LOS2 LOL2 VCC GND VDD VSS SO1CKP SO1CKN INTRX2B SO1DP SO1DN PI1CK PI10D PI11D 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 96 95 94 93 92 91 90 89 88 87 86 85 84 83 78P2352 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 ORDERING INFORMATION PART DESCRIPTION 128-pin LQFP, Open-drain outputs for LOSx, LOLx, INTTRx 128-pin LQFP, CMOS type outputs for LOSx, LOLx, INTTRx 128-pin LQFP w/ Exposed Solder Pad, Open-drain outputs for LOSx, LOLx, INTTRx Tape & Reel option Lead-free option ORDER NUMBER 78P2352-IGT 70P2352-IGT 78P2352-IEL append ‘R’ append ‘/F’ PACKAGE MARK 78P2352-IGT xxxxxxxxxxP6 70P2352-IGT xxxxxxxxxxP6 78P2352-IEL xxxxxxxxxxP6 n/a xxxxxxx-xxx xxxxxxxxxxP6F Page: 41 of 42 PI12D PI13D PTO1CK VSS VDD PO1CK VSS VDD PO13D PO12D VSS VDD PO11D PO10D VSS VDD VDD VSS PO20D PO21D VDD VSS PO22D PO23D VDD VSS PO2CK VDD VSS PTO2CK PI23D PI22D 2006 Teridian Semiconductor Corporation 62 63 64 SCK_MON SEN_CMI SDI_PAR SDO_E4 VCC GND SI2CKP SI2CKN INTTX1B SI2DP SI2DN VCC GND PORB TGND CKSL LOS1 LOL1 FRST SPSL N/C N/C VCC GND SO2CKP SO2CKN INTRX1B SO2DP SO2DN PI2CK PI20D PI21D Rev. 2.4 78P2352 Dual Channel OC-3/ STM1-E/ E4 LIU -v2-0 v2-2 v2-3 v2-4 Revison History Contact Teridian for revision history of earlier releases March 14, 2005: Final Datasheet Release Updated Ordering Numbers to reflect production silicon revision A06 Improved/modified Functional Descriptions for: o Reference Clock, Rx LOS & LOL detectors, Synchronous (Re-Timing) Transmit Modes, Tx FIFO, Tx Driver, Tx LOL detector, and Power-on Reset description Improved/modified Register Descriptions for: o xCMIINV invert bits, FRST, RxLOL, and TxLOL Improved/modified Pin Descriptions for: o PTOCK, FRST, SEN_CMI, GND pin 63 Updated Electrical Specification min/max limits for: o DC Characteristics, o CID, CIU, CIT, and PO pin types o CMI Loss of Signal Conditions August 12, 2005: Changed name and logo from TDK to Teridian Updated Rx and Tx Loss of Lock descriptions Added Full Remote (digital) Loopback and updated Remote (analog) Loopback descriptions August 15, 2006 Updated Ordering Numbers to remove silicon revision A06 Updated Package Mark from C6 to P6 September 20, 2006 Corrected several typos in the mechanical drawing of IGT package If and when manufactured and sold, this product is sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement and limitation of liability. Teridian Semiconductor Corporation (TSC) reserves the right to make changes in specifications at any time without notice. Accordingly, the reader is cautioned to verify that a data sheet is current before placing orders. TSC assumes no liability for applications assistance. Teridian Semiconductor Corp., 6440 Oak Canyon, Irvine, CA 92618 TEL (714) 508-8800, FAX (714) 508-8877, http://www.teridiansemiconductor.com Page: 42 of 42 2006 Teridian Semiconductor Corporation Rev. 2.4
78P2352-IGT 价格&库存

很抱歉,暂时无法提供与“78P2352-IGT”相匹配的价格&库存,您可以联系我们找货

免费人工找货