40TPS12APBF

Bulletin I2107 rev. F 03/03 SAFEIR Series 40TPS.. PHASE CONTROL SCR VT < 1.45V @ 40A ITSM = 500A VRRM = 800 - 1200V Description/ Features The 40TPS... SAFEIR series of silicon controlled rectifiers are specifically designed for medium power switching and phase control applications. The glass passivation technology used has reliable operation up to 125°C junction temperature. Low Igt parts available. Typical applications are in input rectification (soft start) and these products are designed to be used with International Rectifier input diodes, switches and output rectifiers which are available in identical package outlines. Package Outline Major Ratings and Characteristics Characteristics IT(AV) Sinusoidal 40TPS.. Units 35 A 55 A 800 - 1200 V 500 A waveform IRMS VRRM/ VDRM Range ITSM 1.45 V dv/dt VT @ 40 A, TJ = 25°C 1000 V/µs di/dt 100 A/µs - 40 to 125 °C TJ www.irf.com TO-247AC 1 40TPS.. SAFEIR Series Bulletin I2107 rev. F 03/03 Voltage Ratings VRRM/ VDRM, max. repetitive VRSM , maximum non repetitive IRRM/ IDRM peak and off-state voltage peak reverse voltage 125°C V V mA 40TPS08 800 900 10 40TPS12 1200 1300 Part Number Absolute Maximum Ratings Parameters IT(AV) Max. Average On-state Current IT(RMS) Max. Continuous RMS Conditions 40TPS.. Units 35 A @ TC = 79° C, 180° conduction half sine wave A 10ms Sine pulse, rated VRRM applied Initial 10ms Sine pulse, no voltage reapplied TJ = TJ max. 55 On-state Current As AC switch ITSM I2t Max. Peak One Cycle Non-Repetitive 500 Surge Current 600 Max. I 2t for Fusing 1250 A2s 1760 2 I √t 2 Max. I √t for Fusing VT(TO)1 Low Level Value of Threshold 10ms Sine pulse, rated VRRM applied 10ms Sine pulse, no voltage reapplied 12500 2 A √s t = 0.1 to 10ms, no voltage reapplied 1.02 V TJ = 125°C Voltage VT(TO)2 High Level Value of Threshold 1.23 Voltage rt1 Low Level Value of On-state 9.74 mΩ Slope Resistance rt2 High Level Value of On-state 7.50 Slope Resistance VTM Max. Peak On-state Voltage 1.85 V di/dt Max. Rate of Rise of Turned-on Current 100 A/µs IH Max. Holding Current 150 mA IL Max. Latching Current 300 IRRM/ Max. Reverse and Direct 0.5 IDRM Leakage Current 10 dv/dt Max. Rate of Rise 40TPS08 500 of Off-state Voltage 40TPS12 1000 2 mA @ 110A, TJ = 25°C TJ = 25°C TJ = 25°C TJ = 125°C V/µs VR = rated VRRM/ VDRM TJ = TJ max., linear to 80% VDRM , Rg-k = open www.irf.com 40TPS.. SAFEIR Series Bulletin I2107 rev. F 03/03 Triggering Parameters 40TPS.. Units PGM Max. peak Gate Power 10 W PG(AV) Max. average Gate Power 2.5 IGM Max. peak Gate Current Conditions 2.5 A - V GM Max. peak negative Gate Voltage 10 V VGT Max. required DC Gate Voltage 4.0 TJ = - 40°C Anode supply = 6V to trigger 2.5 TJ = 25°C resistive load Max. required DC Gate Current 270 to trigger 150 TJ = 25°C 80 TJ = 125°C 1.7 IGT TJ = 125°C mA 40 TJ = - 40°C TJ = 25°C, for 40TPS08A V GD Max. DC Gate Voltage not to trigger 0.25 V IGD Max. DC Gate Current not to trigger 6 mA TJ = 125°C, V DRM = rated value Thermal-Mechanical Specifications Parameters 40TPS.. Units TJ Max. Junction Temperature Range - 40 to 125 °C Tstg Max. Storage Temperature Range - 40 to 125 RthJC Max. Thermal Resistance Junction 0.6 °C/W Conditions DC operation to Case RthJA Max. Thermal Resistance Junction 40 to Ambient RthCS Max. Thermal Resistance Case 0.2 Mounting surface, smooth and greased to Heatsink wt Approximate Weight T Mounting Torque Case Style www.irf.com 6 (0.21) g (oz.) Min. 6 (5) Kg-cm Max. 12 (10) (lbf-in) TO-247AC 3 40TPS.. SAFEIR Series 40TPS.. Series R thJC (DC) = 0.6 °C/ W 120 110 Conduction Angle 100 30° 90° 120° 180° 80 0 10 20 30 40 120 110 Conduction Period 100 30° 90 60° 90° 120° 80 180° DC 70 0 10 20 30 40 50 Average On-state Current (A) Fig. 2 - Current Rating Characteristics 180° 120° 90° 60° 30° 40 40TPS.. Series RthJC (DC) = 0.6 °C/ W Average On-state Current (A) 60 50 130 Fig. 1 - Current Rating Characteristics RMS Limit 30 20 Conduction Angle 40TPS.. Series TJ= 125°C 10 0 5 10 15 20 25 30 35 Maximum Averag e On-state Power Loss (W) 70 0 Peak Half Sine Wave On-state Current (A) 60° 90 Maximum Allowable Case Temperature (°C) 130 60 80 DC 180° 120° 90° 60° 30° 70 60 50 40 RMSLimit 30 Conduction Period 20 40TPS.. Series TJ = 125°C 10 0 40 0 10 20 30 40 50 60 Avera ge On-sta te Current (A) Avera ge On-sta te Current (A) Fig. 3 - On-state Power Loss Characteristics Fig. 4 - On-state Power Loss Characteristics 550 At Any Ra ted Load Condition And With Rated V RRM Ap plied Following Surge. Initia l TJ= 125°C @60 Hz 0.0083 s @50 Hz 0.0100 s 500 450 400 350 300 250 40TPS.. Series 1 10 100 Number Of Equal Amplitude Half Cycle Current Pulses (N) Fig. 5 - Maximum Non-Repetitive Surge Peak Half Sine Wa ve On-state Current (A) Maximum Avera g e On-state Power Loss (W) Maximum Allowable Case Temperature (°C) Bulletin I2107 rev. F 03/03 600 Ma ximum Non Rep etitive Surge Current Versus Pulse Train Duration. Control Of Conduction May Not Be Maintained. Initial TJ = 125°C No Voltage Reap p lied Rated VRRM Reap p lied 550 500 450 400 350 300 40TPS.. Series 250 0.01 0.1 1 Pulse Tra in Duration (s) Fig. 6 - Maximum Non-Repetitive Surge Current Current 4 www.irf.com 40TPS.. SAFEIR Series Bulletin I2107 rev. F 03/03 Instanta neous On-sta te Current (A) 100 10 TJ= 25°C TJ= 125°C 40TPS.. Series 1 0.5 1 1.5 2 Instantaneous On-state Voltag e (V) Fig. 7 - On-state Voltage Drop Characteristics 10 Rec tangular gate pulse a)Rec ommended load line for rated di/ dt: 20 V, 30 ohms tr = 0.5 µs, tp >= 6 µs b)Rec ommended load line for = 6 µs (1) PGM = 100 W, tp = 500 µs (2) PGM = 50 W, tp = 1 ms (3) PGM = 20 W, tp = 25 ms (4) PGM = 10 W, tp = 5 ms (a) (b) VGD IGD 0.1 0.001 TJ = -40 °C TJ = 125 °C 1 TJ = 25 °C Instantaneous Gate Voltage (V) 100 (4) (3) 40TPS.. 0.01 0.1 (2) (1) Frequenc y Limited by PG(AV) 1 10 100 1000 Instantaneous Gate Current (A) Transient Thermal Impeda nc e Z thJC (°C/W) Fig. 8 - GateCharacteristics 1 0.1 Steady State Value (DC Opera tion) D = 0.50 D = 0.33 D = 0.25 D = 0.17 D = 0.08 Single Pulse 40TPS.. Series 0.01 0.0001 0.001 0.01 0.1 1 Square Wave Pulse Duration (s) Fig. 9 - Thermal Impedance ZthJC Characteristics www.irf.com 5 40TPS.. SAFEIR Series Bulletin I2107 rev. F 03/03 Outline Table 3. 65 ( 0 .14 4) 15 .90 (0 .626 ) 3. 55 ( 0 .13 9) DIA. 15 .30 (0 .602 ) 5. 30 ( 0 .20 9) 4.70 ( 0.185) 2.5 ( 0.098) 1.5 ( 0.059) 5. 70 (0 .22 5) 5.30 ( 0.208) 20 .30 (0 .800 ) 19 .70 (0 .775 ) 5.50 ( 0.217) 4. 50 (0 .17 7) 1 2 ( 2 PLCS.) 3 14. 80 ( 0.583) 14 .20 (0 .559 ) 4. 30 ( 0 .17 0) 3. 70 ( 0 .14 5) 2. 20 (0 .08 7) 1. 40 ( 0 .05 6) 2. 40 (0 .09 5) M AX. M AX. 1. 00 ( 0 .03 9) 0.80 ( 0.032) 0. 40 ( 0 .21 3) 10. 94 ( 0.430) 10 .86 ( 0 .427 ) Dimensions in millimeters and inches Marking Information EXAMPLE: THIS IS A 40TPS12 WITH ASSEMBLY LOT CODE 5657 ASSEMBLED ON WW 35, 2000 IN THE ASSEMBLY LINE "H" INTERNATIONAL RECTIFIER LOGO 035H 56 ASSEMBLY LOT CODE 6 PART NUMBER 40TPS12 57 DATE CODE YEAR 0 = 2000 WEEK 35 LINE H www.irf.com 40TPS.. SAFEIR Series Bulletin I2107 rev. F 03/03 Ordering Information Table Device Code 1 - 2 - 40 T P S 12 1 2 3 4 5 2 (A) 6 Current Rating Circuit Configuration: 1 (K) (G) 3 T = Thyristor 3 - 4 - 5 - 6 - Package: T = TO-247 Type of Silicon: S = Standard Recovery Rectifier Voltage code: Code x 100 = VRRM None = Standard Igt selection 08 = 800V 12 = 1200V A = Low Igt selection 40mA max. only for 40TPS08A Data and specifications subject to change without notice. This product has been designed and qualified for Industrial Level. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 03/03 www.irf.com 7