BFC280905003

BFC2 809 05... www.vishay.com Vishay BCcomponents Film Dielectric Trimmers FEATURES • High temperature type • Housing dimensions: 6 mm x 8 mm x 9 mm • For a basic grid of 2.54 mm • Top and bottom adjustment • Round head • Mounting: radial • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS • Antennas • Impedance matching circuits • Medical • RF • For fine adjustment in professional applications QUICK REFERENCE DATA Rated DC voltage 300 VDC Test DC voltage for 1 min 600 VDC Maximum contact resistance 5 m Minimum insulation resistance between stator and rotor Category temperature range -40 °C to +125 °C Climatic category (IEC 60068) 40/125/21 Minimum storage temperature -55 °C Related specification IEC 60418-1 and 4 Effective angle of rotation Operating torque Maximum axial thrust Capacitance range (Cmin. / Cmax.) Life of trimmer 10 000 M 180° (rotation in 180° only, see “Life of trimmer”) Cmax. < 3.5 pF 1 mNm to 15 mNm Cmax.  3.5 pF 1 mNm to 20 mNm 2N 1.2 pF / 3.5 pF to 2 pF / 18 pF Maximum 10 cycles: rotation in 180° only (the electrical and mechanical performance is not guaranteed if rotated beyond 10 cycles) Sampling and data evaluation for quality level in accordance with “MIL-STD-105D” and “IEC 60410”: Quality level < 0.15 % major defects < 0.65 % minor defects Each capacitor is tested for minimum Cmax. and is also subjected to the full test voltage. Revision: 04-Aug-15 Document Number: 28529 1 For technical questions, contact: dc-film@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 BFC2 809 05... www.vishay.com Vishay BCcomponents DIMENSIONS in millimeters Ø 2.2 0.6 0.5 min. 9 max. Sprue Z Color mark 3.7 ± 0.2 1.1 max. Ø 2.2 5.08 ± 0.2 1.1 ± 0.2 3 ± 0.2 DETAIL Z turned 90° Ø 1.4 6.4 max. 6.7 max. 0.85 max. 0.6 ± 0.1 7.4 max. 0.5 ± 0.15 Trimmers BFC2 809 05... series, with round heads 5.08 1.9 R S 2.3 ± 0.1 1.2 (2 x) Hole pattern ADJUSTMENT For top adjustment a screwdriver or trimming key can be used; for bottom adjustment a key is required as shown below. Ø 2.2 Ø 1.5 + 0.1 0 0.6 + 0.2 0 0.7 + 0.1 0 2 min. Bottom adjustment key Revision: 04-Aug-15 Document Number: 28529 2 For technical questions, contact: dc-film@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 BFC2 809 05... www.vishay.com Vishay BCcomponents ORDERING INFORMATION CATALOG NUMBER BFC2 809 05... Cmin. / Cmax. (pF) TOP AND BOTTOM ADJUSTMENT ROUND HEAD ROUND HEAD AND FLUX GUARD 215 216 217 001 002 003 1.2 / 3.5 1.8 / 10 2 / 18 MOUNTING The trimmer can be mounted on printed-circuit boards with a minimum hole diameter of 2.54 mm. PACKAGING Blister packs of 70 units each. For smallest packaging quantity (SPQ) see “Electrical Data” table. ELECTRICAL DATA tan  AT Cmax. x 10-4 GUARANTEED MAX. Cmin. / MIN. Cmax. AT 200 kHz (pF) SHAPE OF HEAD FIG. 1.2 / 3.5 Round 1.8 / 10 2 / 18 1 MHz 100 MHz TEMP. COEFF. (1) (10-6/K) 1  10  20 -250 ± 350 850 Orange Round 1  10  20 -250 ± 350 1200 580 None White Round 1  10  25 -250 ± 350 360 Red MIN. fres AT Cmax. (MHz) COL. OF DOT SPQ CATALOG NUMBER BFC2 ... ..... 700 700 700 700 700 700 .... 809 05001 .... 809 05215 .... 809 05002 .... 809 05216 .... 809 05217 .... 809 05003 Note (1) C: 60 % to 80 % of C max.; Tamb: from +20 °C to +125 °C SOLDERING CONDITIONS For general soldering conditions and wave soldering profile, we refer to the application note “Soldering Guidelines for Film Capacitors”: www.vishay.com/doc?28171 TEST PROCEDURES AND REQUIREMENTS IEC 60418-1 CLAUSE IEC 60068 TEST METHOD TEST PROCEDURE REQUIREMENTS 4.2 Method of mounting Method A 14 Capacitance drift After TC measurement C/C:  2.5 %; 4 % for 2 pF 19 Thrust Axial thrust of 2 N C/C:  0.3 % 21 Robustness of terminations: 1 N No damage 21.1 Ua 21.2 Ub Bending 1 cycle No damage 22 Na Rapid change of temperature 1 cycle; 0.5 h at lower and  0.5 h at upper category temperature C/C:  2.5 % 23 T Soldering: Ta Solderability Solder bath immersion 3 mm; 235 °C; 2 s Good wetting, no mechanical damage Tb Resistance to heat Solder bath: 260 °C; 10 s No mechanical damage Revision: 04-Aug-15 Tensile Document Number: 28529 3 For technical questions, contact: dc-film@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 BFC2 809 05... www.vishay.com Vishay BCcomponents TEST PROCEDURES AND REQUIREMENTS IEC 60418-1 CLAUSE IEC 60068 TEST METHOD 24 Eb Impact bump 4000 ± 10 bumps; 40 g; 6 ms C/C:  0.6 %; no mechanical damage 25 Fc Vibration Frequency 10 Hz to 55 Hz; amplitude 0.35 mm; 1.5 h C/C:  0.6 %; no mechanical damage 26 TEST PROCEDURE REQUIREMENTS C/C:  2.5 Climatic sequence: 26.1 B Dry heat 16 h at upper category temperature tan :  10 x 10-4 for Cmax. < 18 pF; tan :  40 x 10-4 for Cmax.  18 pF  Rins.:  10 000 M; rotor contact R:  5 m 26.2 D Damp heat accelerated, first cycle 1 cycle; 24 h; +40 °C; 95 % to 100 % RH Voltage proof: 600 V for 1 min 26.3 Aa Cold 16 h; -40 °C Visual examination: no mechanical damage Damp heat accelerated, remaining cycles 1 cycle; 24 h; +40 °C;  95 % to 100 % RH Operating torque:  1 mNm to 20 mNm Damp heat steady state 21 days; +40 °C;  90 % to 95 % RH C/C:  2.5 %  tan :  10 x 10-4 for Cmax. < 18 pF; tan :  25 x 10-4 for Cmax.  18 pF  Rins.:  10 000 M; rotor contact R:  5 m  Voltage proof: 600 V for 1 min  Visual examination: no mechanical damage  Operating torque: 1 mNm to 20 mNm Mechanical endurance 10 cycles  Maximum 10 cycles: rotation in 180° only (the electrical and mechanical performance is not guaranteed if rotated beyond 10 cycles) C/C:  0.3 %;  2.5 % for 2 pF C/C after axial thrust:  0.3 %; rotor contact R:  5 m  Voltage proof: 600 V for 1 min  Visual examination: no mechanical damage  Operating torque:  1 mNm to 20 mNm 26.5 27 Ca 29 Revision: 04-Aug-15 Document Number: 28529 4 For technical questions, contact: dc-film@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000