BRT12H-X001

BRT11, BRT12, BRT13 www.vishay.com Vishay Semiconductors Optocoupler, Phototriac Output, Non-Zero Crossing FEATURES • ITRMS = 300 mA • High static dV/dt < 10 000 V/μs A 1 6 MT2 • Electrically insulated between input and output circuit C 2 5 NC • Microcomputer compatible - very low trigger current NC 3 • Trigger current - (IFT < 1.2 mA) BRT12F - (IFT < 2 mA) BRT11H, BRT12H, BRT13H - (IFT < 3 mA) BRT11M, BRT12M, BRT13M 4 MT1 • Non-zero voltage detectors high input sensitivity • Compliant to RoHS Directive 2002/95/EC and in accordance to WEEE 2002/96/EC i179004-10 DESCRIPTION APPLICATIONS The BRT11, BRT12, and BRT13 product family consists of AC optocouplers non-zero voltage detectors consisting of two electrically insulated lateral power ICs which integrate a thyristor system, a photo detector and noise suppression at the output and an IR GaAs diode input. • Industrial controls • Office equipment • Consumer appliances AGENCY APPROVALS • UL 1577, file no. E52744 system code H • DIN EN 60747-5-2 (VDE 0844)/DIN EN 60747-5-5 (pending) available with option 1 • CQC ORDERING INFORMATION DIP-6 B R T 1 # x - X PART NUMBER 0 # PACKAGE OPTION # TAPE AND REEL 7.62 mm 10.16 mm Option 7 Option 9 > 0.1 mm > 0.7 mm VDRM (V) AGENCY CERTIFIED/PACKAGE UL ≤ 400 ≤ 600 IFT = 2 mA IFT = 3 mA DIP-6 Option 6 T ≤ 800 IFT = 1.2 mA IFT = 2 mA IFT = 3 mA IFT = 2 mA IFT = 3 mA BRT11H BRT11M BRT12F BRT12H BRT12M BRT13H BRT13M DIP-6, 400 mil, option 6 - - BRT12F-X006 BRT12H-X006 - BRT13H-X006 - SMD-6, option 7 - - - BRT13H-X007T (1) - SMD-6, option 9 - - - BRT13H-X009T IFT = 3 mA UL, VDE IFT = 2 mA IFT = 3 mA BRT12F-X007T (1) BRT12H-X007T (1) - BRT12H-X009T IFT = 1.2 mA IFT = 2 mA IFT = 3 mA IFT = 2 mA DIP-6 - - - BRT12H-X001 BRT12M-X001 - - DIP-6, option 6 - - BRT12F-X016 BRT12H-X016 BRT12M-X016 BRT13H-X016 - SMD-6, option 7 - - - - - BRT13H-X017T (1) - Note (1) Also available in tube, do not put T on the end. Document Number: 83689 1 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.6, 02-Dec-11 BRT11, BRT12, BRT13 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL VALUE UNIT INPUT Reverse voltage VR 6 V Forward current IF 20 mA Surge forward current Power dissipation t ≤ 10 μs IFSM 1.5 A Pdiss 30 mW OUTPUT Repetitive peak off-state voltage RMS on-state current Single cycle surge current 50 Hz Power dissipation BRT11 VDRM 400 V BRT12 VDRM 600 V BRT13 VDRM 800 V ITRMS 300 mA ITSM 3 A Pdiss 600 mW COUPLER Maximum power dissipation Ptot 630 mW Isolation test voltage (between emitter and detector, climate per DIN 500414, part 2, Nov. 74) (1) VISO 5300 VRMS Reference voltage in accordance with VDE 0110 b Vref 500 VRMS Reference voltage in accordance with VDE 0110 b (insulation group C) Vref 600 VDC Creepage distance ≥ 7.2 mm Clearance distance ≥ 7.2 mm Comparative tracking index per DIN IEC 112/VDE 0303 part 1 group IIIa according to DIN VDE 0109 CTI ≥ 175 VIO = 500 V, Tamb = 25 °C RIO ≥ 1012 VIO = 500 V, Tamb = 100 °C RIO ≥ 1011 Ω Storage temperature range Tstg - 40 to + 150 °C Ambient temperature range Tamb - 40 to + 100 °C Isolation resistance Ω Notes • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Test AC voltage in accordance with DIN 57883, June 1980. Document Number: 83689 2 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.6, 02-Dec-11 BRT11, BRT12, BRT13 www.vishay.com Vishay Semiconductors ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. 1.1 UNIT INPUT Forward voltage IF = 10 mA VF 1.35 V Reverse current VR = 6 V IR 10 μA RthJA 750 °C/W Thermal resistance, junction to ambient (1) OUTPUT BRT11 Peak off-state voltage ID(RMS) = 100 μA Off-state current TC = 80 °C, VDRM ID BRT12 VDM BRT13 On-state voltage Pulse current Critical rate of rise of off-state voltage Critical rate of rise of voltage at current commutation μA 600 μA 800 μA 0.5 100 μA IT = 300 mA VT 2.3 V tp ≤ 5 μs, f = 100 Hz, dItp/dt ≤ 8 A/μs Itp 2 A VD = 0.67 VDRM, Tj = 25 °C dV/dtcr 10 kV/μs VD = 0.67 VDRM, Tj = 80 °C dV/dtcr 5 kV/μs VD = 0.67 VDRM, Tj = 25 °C, dI/dtcrq ≤ 15 A/ms dV/dtcrq 10 kV/μs VD = 0.67 VDRM, Tj = 80 °C, dI/dtcrq ≤ 15 A/ms dV/dtcrq 5 kV/μs dI/dtcr 8 A/μs Critical rate of rise of on-state at current Holding current 400 VD = 10 V Thermal resistance, junction to ambient IH 80 RthJA 500 μA 125 °C/W COUPLER Trigger current VD = 10 V, F - versions IFT 1.2 mA VD = 10 V, H - versions IFT 0.4 2 mA VD = 10 V, M - versions IFT 0.8 3 mA 14 μA/°C 2 pF Trigger current temperature gradient ΔIFT/ΔTj Capacitance (input to output) f = 1 MHz, VR = 0 V 7 CIO Notes • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. (1) Static air, SITAC soldered in PCB or base plate. TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) tgd 10 3 Ptot t gd= f(IF/IFT25 °C) 0.6 W P tot = (ITRMS) 0.5 VD = 200 V 102 0.4 5 TJ = 25°C 100°C 0.3 101 180° 120° 90° 60° 30° 0.2 5 0.1 100 100 5 101 5 102 IF/IFT25°C 17239 Fig. 1 - Typical Trigger Delay Time 0.0 17240 0 100 200 mA 300 /TRMS Fig. 2 - Power Dissipation 60 Hz to 60 Hz Line Operation Document Number: 83689 3 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.6, 02-Dec-11 BRT11, BRT12, BRT13 www.vishay.com ID 10 - 3 nA Vishay Semiconductors -3 IT 10 mA ID = f(Tj) IT = ƒ(VT) VD = 800 V 10 - 2 5 Tj = 25 °C 100 °C 10 - 2 5 10 - 1 5 10 - 1 10 - 0 5 5 10 - 1 0 20 40 60 80 °C 100 TJ 17241 10 - 0 0 1 2 3 V Fig. 3 - Typical Off-State Current 4 VT 17244 Fig. 6 - Typical Output Characteristics ITRMS 400 mA IFTN=f(tpIF) IFTN normalized to IFT refering to tpIF ≥ 1 m ITRMS = ƒ(TA) R thJA = 125 K/W 3) 300 Vop=220V,f= 4 0 ...60Hz typ. 200 100 0 17242 0 Fig. 4 - Pulse Trigger Current IF 20 40 60 80 °C 100 TA 17245 Fig. 7 - Current Reduction 10 - 2 mA IF = ƒ(VF) 10 - 1 5 Tj = 75 °C 50 °C 25 °C 10 - 0 ITRMS = ƒ(T PIN5) 5 RthJ-PIN5= 16,5 K/W 4) 10 - 1 0.9 17243 1.0 1.1 V 1.2 VF Fig. 5 - Typical Input Characteristics 17246 Fig. 8 - Current Reduction Document Number: 83689 4 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.6, 02-Dec-11 BRT11, BRT12, BRT13 www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 3 2 pin one ID 1 6.4 ± 0.1 ISO method A 4 9.78 ± 0.25 6 5 8.6 ± 0.1 7.62 ref. 1.27 ± 0.05 1 min. 0.1755 ± 0.0735 0.30 typ. 3.555 ± 0.255 4° typ. 0.485 ± 0.025 15° max. 0.84 typ. 0.84 typ. 0.765 ± 0.255 2.54 typ. 17222 Option 6 Option 7 Option 8 Option 9 7.62 typ. 7.62 typ. 7.62 typ. 10.3 max. 7.62 typ. 3.5 ± 0.3 0.7 min. 0.25 ± 0.1 4.3 ± 0.3 3.5 ± 0.3 0.1 ± 0.1 3.6 ± 0.3 0.1 min. 2.55 ± 0.25 8 min. 0.6 min. 10.3 max. 9.27 min. 12.1 max. 10.16 typ. 0.6 min. 8 min. 20802-40 PACKAGE MARKING (example) BRT12H V YWW H 68 Notes • Only options 1, and 7 are reflected in the package marking. • The VDE logo is only marked on option 1 parts. • Tape and reel suffix (T) is not part of the package marking. Document Number: 83689 5 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.6, 02-Dec-11 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000