CRA04S04315R0JTD

CRA04S Vishay Thick Film Resistor Array FEATURES • Convex terminal array with square corners • • • • Wide ohmic ramge: 10R to 1M0 4 or 8 terminal package with isolated resistors Lead (Pb)-free solder contacts on Ni barrier layer Pure tin plating provides compatibility with lead (Pb)-free and lead containing soldering processes • Compatible with “Restriction of the use of Hazardous Substances” (RoHS) directive 2002/95/EC (issue 2004) The CRA04S thick film resistor array is constructed on a high grade ceramic body with convex terminations. A small package enables the design of high density circuits. The single component reduces board space, component counts, and assembly costs. STANDARD ELECTRICAL SPECIFICATIONS MODEL CIRCUIT CRA04S 03 POWER RATING P70 °C W LIMITING ELEMENT VOLTAGE MAX. V≅ TEMPERATURE COEFFICIENT ppm/K ± 100 0.063 50 ± 200 Zero-Ohm-Resistor: Rmax. ≤ 50 mΩ, Imax. = 1 A TOLERANCE % RESISTANCE RANGE Ω E-SERIES ±1 ± 2; ± 5 10R - 1M0 24 + 96 24 TECHNICAL SPECIFICATIONS PARAMETER Rated Dissipation at 70 °C (2) UNIT CRA04S W per element 0.063 Limiting Element Voltage (1) V≅ 50 Vdc/ac peak 100 Category Temperature Range °C - 55 to + 155 Insulation Resistance Ω > 109 Insulation Voltage (1 min) Notes (1) Rated voltage: P × R (2) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rate dissipation applies only if the permitted film temperature of 155 °C is not exceeded. PART NUMBER AND PRODUCT DESPRIPTION PART NUMBER: CRA04S08347K0JTD (3) C R A 0 4 S 0 8 3 4 7 K 0 J T D MODEL TERMINAL STYLE PIN CIRCUIT VALUE TOLERANCE PACKAGING (4) SPECIAL CRA04 S 04 08 3 = 03 R = Decimal K = Thousand M = Million 0000 = 0 Ω Jumper F=±1% G=±2% J=±5% Z = 0 Ω Jumper TD TC PZ Up to 2 digits PRODUCT DESCRIPTION: CRA04S 08 03 473 J RT7 e3 CRA04S 08 03 473 J RT7 e3 LEAD (Pb)-FREE e3 = Pure tin Termination finish MODEL TERMINAL COUNT CIRCUIT TYPE RESISTANCE VALUE TOLERANCE PACKAGING (4) CRA04S 04 08 03 473 = 47 kΩ 4702 = 47 kΩ 10R0 = 10 Ω 100 = 10 Ω 000 = 0 Ω Jumper First two digits (3 for 1 %) are significant. Last digit is the multiplier. F=±1% G=±2% J=±5% Z = 0 Ω Jumper RT7 RT6 PZ Notes Preferred way for ordering products is by use of the PART NUMBER Please refer to the table PACKAGING, see next page (3) (4) www.vishay.com 248 For technical questions, contact: filmresistors.thickfilmchip@vishay.com Document Number: 31043 Revision: 13-Oct-08 CRA04S Thick Film Resistor Array Vishay PACKAGING PACKAGING CODE MODEL TAPE WIDTH CRA04S 8 mm DIAMETER PITCH PIECES/REEL PAPER TAPE PART NUMBER PRODUCT DESCRIPTION 180 mm/7" 2 mm 10 000 TD RT7 330 mm/13" 2 mm 20 000 TC RT6 330 mm/13" 2 mm 50 000 PZ PZ Rated Power in % CIRCUIT 03 CIRCUIT 120 100 80 60 40 20 4 pin 8 pin 0 - 55 - 25 0 25 50 Derating 75 70 100 125 155 175 Ambient Temperature in °C DIMENSIONS PIN NO# DIMENSIONS [in millimeters] L A A1 B B* PNOM T W 4 1.0 ± 0.1 - 0.33 0.15 0.25 0.65 0.35 1.0 8 2.0 ± 0.2 0.30 0.4 0.15 0.25 0.50 0.45 1.0 - ± 0.1 ± 0.15 TOL. - ± 0.15 ± 0.15 ± 0.10 ± 0.1 SOLDER PAD DIMENSIONS [in millimeters] WAVE a e Document Number: 31043 Revision: 13-Oct-08 e c w d a b e 0.45 1.45 0.2 0.4 0.5 0.3 The dimensions shown are for a 8 pin part. For parts with different pin numbers use the same pitch and add or substract pads as required. For technical questions, contact: filmresistors.thickfilmchip@vishay.com www.vishay.com 249 CRA04S Thick Film Resistor Array Vishay TEST PROCEDURES AND REQUIREMENTS EN 60115-1 REQUIREMENTS PERMISSIBLE CHANGE (ΔR/R) (1) TEST (clause) CONDITIONS OF TEST STABILITY CLASS 1 OR BETTER STABILITY CLASS 2 OR BETTER 10 Ω to 1 MΩ 10 Ω to 1 MΩ - ±1% ± 2 %; ± 5 % 20/- 55/20 °C and 20/125/20 °C ± 100 ppm/K ± 200 ppm/K U = 2.5 × (P70 x R)1/2 ≤ 2 x Umax.; 0.5 s ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) Stability for product types: CRA04S Resistance (4.5) Temperature coefficient (4.8.4.2) Overload (4.13) Aging 4 h at 155 °C, dryheat solder bath method; 235 °C; 2 s visual examination Solderability (4.17.5) (2) Good tinning (≥ 95 % covered) no visible damage Resistance to soldering heat (4.18.2) Solder bath method; (260 ± 5) °C; (10 ± 1) s ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) Rapid change of temperature (4.19) 30 min at LCT = - 55 °C; 30 min at UCT = 125 °C; 5 cycles ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) (40 ± 2) °C; 56 days; (93 ± 3) % RH ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) 16 h at UCT = 125 °C; 1 cycle at 55 °C; 2 h at LCT = - 55 °C; 1 h/1 kPa at 15 °C to 35 °C; 5 cycles at 55 °C U = (P70 x R)1/2 U = Umax.; whichever is less severe ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) U = (P70 x R)1/2 U = Umax.; whichever is less severe 1.5 h ON; 0.5 h OFF; 70 °C; 1000 h ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) Duration extended to 8000 h ± (2 % R + 0.1 Ω) ± (4 % R + 0.1 Ω) UCT = 125 °C; 1000 h ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) Damp heat, steady state (4.24) Climatic sequence (4.23) Endurance at 70 °C (4.25.1) Extended endurance (4.25.1.8) Endurance at upper category temperature (4.25.3) Notes (1) Figures are given for a single element (2) Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years APPLICABLE SPECIFICATIONS • EN 60115-1 Generic Specification • EN 140400 Sectional Specification • EN 140401-802 Detail Specification • IEC 60068-2-X Variety of environmental test procedures • EIA 481 Packaging of SMD components www.vishay.com 250 For technical questions, contact: filmresistors.thickfilmchip@vishay.com Document Number: 31043 Revision: 13-Oct-08 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000