CRA06S0831M00JTA

CRA06E and S Vishay Dale Thick Film, Resistor Array FEATURES • Convex terminal array available with either scalloped corners (E version) or square corners (S version) Wide ohmic range: 10R to 1M0 4 or 8 terminal package with isolated resistors Lead (Pb)-free solder contacts on Ni barrier layer Pure tin plating provides compatibility with Lead (Pb)-free and lead containing soldering processes • Compatible with "Restriction of the use of Hazardous Substances" (RoHS) directive 2002/95/EC (issue 2004) • Operating temperature range of - 55°C to + 150°C • • • • CRA06E and CRA06S Thick Film resistor arrays are constructed on a high grade ceramic body with convex terminations. A small package enables the design of high density circuits. The single component reduces board space, component counts and assembly costs. STANDARD ELECTRICAL SPECIFICATIONS MODEL POWER RATING CIRCUIT P70°C W LIMITING ELEMENT VOLTAGE MAX. V쓖 CRA06E 0.063 03 CRA06S Jumper: Zero-Ohm-Resistor available; R ≤ 50m Ω TEMPERATURE COEFFICIENT ppm/K 100 200 50 TOLERANCE RESISTANCE RANGE E-SERIES Ω % ±1 ± 2; ± 5 10R - 1M0 10R - 1M0 24 - 96 24 TECHNICAL SPECIFICATIONS CRA06E & S PARAMETER UNIT Rated Dissipation at 70°C Limiting Element Voltage 1) Insulation Voltage (1min) Category Temperature Range Insulation Resistance W V쓖 1) Rated voltage: 03 CIRCUIT 0.063 50 100 - 55 to + 150 > 10 10 Vdc/ac peak °C Ω P*R PART NUMBER AND PRODUCT DESCRIPTION PART NUMBER: CRA06S08310K0JTA C R A 0 6 S 0 8 3 1 0 K 0 J T A MODEL TERMINAL STYLE PIN CIRCUIT VALUE TOLERANCE PACKING SPECIAL CRA06 S E 04 08 3 = 03 R = Decimal K = Thousand M = Million 0000 = 0Ω Jumper F = ± 1% G = ± 2% J = ± 5% Z = 0Ω Jumper TA = RT1 TC = RT6 up to 2 digits PRODUCT DESCRIPTION: CRA06S 08 03 473 J RT1 e3 CRA06S 08 03 473 MODEL TERMINAL COUNT CIRCUIT TYPE RESISTANCE VALUE CRA06S CRA06E 04 08 03 473 = 47KΩ 4702 = 47KΩ 10R0 = 10Ω 100 = 10Ω 000 = 0Ω Jumper 1) Please refer to table PACKING, page 8. J RT1 e3 TOLERANCE PACKING1) LEAD (Pb)-FREE F = ± 1% G = ± 2% J = ± 5% Z = 0Ω Jumper RT1 RT6 e3 = Pure Tin Termination Finish First two digits (three for 1 %) are significant. Last digit is the multiplier NOTE: Products can be ordered using either the Product Description or the Part Number. www.vishay.com 6 For Technical Questions, contact: ff3aresistors@vishay.com Document Number 31002 Revision 16-Aug-05 CRA06E and S Vishay Dale Thick Film, Resistor Array DIMENSIONS 8-Terminal device S - Version 103 E - Version 103 1 A PIN 1 d e a a PIN MODEL NO# e SOLDER PAD DIMENSIONS [in millimeters] DIMENSIONS [in millimeters] L A A1 B B* P T W CRA06S 4 1.6 0.38 0.61 0.3 0.3 0.8 0.5 1.5 CRA06E 8 3.2 0.38 - 0.3 0.3 0.8 0.5 1.5 CRA06S 8 3.2 0.38 0.61 0.3 0.3 0.8 0.5 1.5 Tol ± 0.15 ± 0.15 ± 0.15 ± 0.15 ± 0.15 ± 0.1 ± 0.1 ± 0.15 MODEL PINS c w d CRA06S 4 0.8 3.1 0.36 8 0.8 3.1 0.36 CRA06E p a b e 0.44 1.15 0.8 0.44 1.15 0.63 CRA06S DESCRIPTION ASSEMBLY Production is strictly controlled and follows a set of instructions established for reproducibility. A thick film layer is deposited on a high grade ceramic substrate. The resistor elements are covered by a protective coating designed for electrical, mechanical and climatic protection. The wrap around terminations receive a final pure tin on nickel plating. The resistors are suitable for processing on automatic SMD assembly systems. They are suitable for automatic soldering using wave and solder paste reflow. Due to the design, arrays have automatic placement capability. The resistors are Lead (Pb)-free, the pure tin plating provides compatibility with Lead (Pb)-free and Lead-containing soldering processes. All products comply with the CEFIC-EECA-EICTA list of legal restrictions on hazardous substances. The result of the determined production is verified by an extensive testing procedure. Only accepted products are laid directly into the paper tape in accordance with EIA 481. This includes full compatibility with the following directives: • 2000/53/EC End of Vehicle Life Directive (ELV) • 2000/53/EC Annex II to End of Vehicle Life Directive (ELV II) • 2002/95/EC Restriction of the use of Hazardous Substances Directive (RoHS) • 2002/96/EC Waste Electrical and Electronic Equipment Directive (WEEE) Solderability is specified for 2 years after production or requalification. The permitted storage time is 20 years. Document Number 31002 Revision 16-Aug-05 For Technical Questions, contact: ff3aresistors@vishay.com www.vishay.com 7 CRA06E and S Thick Film, Resistor Array Vishay Dale CIRCUIT 03 CIRCUIT 4 pin 8 pin 175 PACKING PACKING CODE MODEL TAPE WIDTH DIAMETER PIECES PITCH 8 mm 180 mm/7" 5 000 4 mm RT1 8 mm 330 mm/13" 20 000 4 mm RT6 PAPER CRA06 www.vishay.com 8 For Technical Questions, contact: ff3aresistors@vishay.com Document Number 31002 Revision 16-Aug-05 CRA06E and S Thick Film, Resistor Array Vishay Dale PERFORMANCE TEST CONDITIONS OF TEST Endurance Test at 70°C per EIA 575 1000 hour at 70°C, 1.5 hours "ON", 0.5 hours "OFF" ± 1.0 % Overload per EIA 575 Short time overload 2.5 x rated continuous working voltage for 5 seconds. Not to exceed 2 x max operating voltage ± 0.5 % Thermal Shock per EIA 575-3.5 ± 0.5 % Moisture Resistance per EIA 575-3.10 ± 1.0 % Resistance to Soldering Heat EIA 575 10 seconds at 260°C solder bath temperature ± 2.0 % High Temperature Exposure per EIA 575-3.7 ± 1.0 % Low Temperature Operations per EIA-575-3.6 ± 0.5 % Solderability & Leaching EIA 575-3.12 Document Number 31002 Revision 16-Aug-05 For Technical Questions, contact: ff3aresistors@vishay.com TEST RESULTS 95 % Coverage www.vishay.com 9