CRA12E08375R0FTR

CRA12E & S Vishay Thick Film Resistor Array FEATURES • Convex • • • • • terminal array available with either scalloped corners (E version) or square corners (S version) Wide ohmic range: 10R to 1M0 4, 8, 10 or 16 terminal package with isolated resistors Lead (Pb)-free solder contacts on Ni barrier layer Pure tin plating provides compatibility with lead (Pb)-free and lead containing soldering processes Compatible with "Restriction of the use of Hazardous Substances" (RoHS) directive 2002/95/EC (issue 2004) STANDARD ELECTRICAL SPECIFICATIONS MODEL CIRCUIT LIMITING ELEMENT VOLTAGE MAX. V≅ POWER RATING P70 °C W 01; 02; 20 CRA12E CRA12S 0.100 50 0.125 03 TEMPERATURE COEFFICIENT ppm/K RESISTANCE RANGE Ω TOLERANCE % ± 100 ±1 ± 200 ± 2; ± 5 10R - 1M0 E-SERIES 24 + 96 24 Zero-Ohm-Resistor: Rmax = 50 mΩ, Imax = 1.5 A TECHNICAL SPECIFICATIONS PARAMETER Rated Dissipation at 70 °C2) UNIT CRA12E & S - 01/02/20 CIRCUIT W per element 0.1 Limiting Element Voltage1) V≅ Insulation Voltage (1 min) CRA12E & S - 03 CIRCUIT 0.125 50 Vdc/ac peak 100 Category Temperature Range °C - 55/+ 125 (+ 155) Insulation Resistance Ω > 109 Notes 1. Rated voltage: P × R 2. The power dissiaption on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if permitted film temperature of 155 °C is not exceeded. PART NUMBER AND PRODUCT DESCRIPTION PART NUMBER: CRA12E08347K0JTR1) C MODEL CRA12 R A TERMINAL STYLE S E 1 2 E PIN 04 08 10 16 0 8 CIRCUIT 1 = 01 2 = 02 3 = 03 8 = 20 3 4 7 VALUE R = Decimal K = Thousand M = Million 0000 = 0 Ω Jumper K 0 J TOLERANCE F=±1% G=±2% J=±5% Z = 0 Ω Jumper T R PACKAGING2) TR TL SPECIAL up to 2 digits PRODUCT DESCRIPTION: CRA12S 08 03 473 J RB8 e3 CRA12S 08 03 473 J RB8 e3 MODEL CRA12E CRA12S TERMINAL COUNT 04 08 10 16 CIRCUIT TYPE 01 02 03 20 RESISTANCE VALUE 473 = 47 kΩ 4702 = 47 kΩ 10R0 = 10 Ω 100 = 10 Ω 000 = 0 Ω Jumper TOLERANCE F=±1% G=±2% J=±5% Z = 0 Ω Jumper PACKAGING2) RB8 RD7 LEAD (Pb)-FREE e3 = Pure Tin Termination Finish First two digits (three for 1 %) are significant. Last digit is the multiplier Notes 1. Preferred way for ordering products is by use of the PART NUMBER 2. Please refer to table PACKAGING, see next page www.vishay.com 260 For technical questions, contact: ff3aresistors@vishay.com Document Number: 31003 Revision: 08-Feb-07 CRA12E & S Thick Film Resistor Array Vishay AVAILABLE TYPES AND RANGES TERMINAL COUNT MODEL CRA12 S CIRCUIT 08 03 10 01 02 03 20 04 01 03 08 CRA12 E TEMPERATURE COEFFICIENT TOLERANCE ± 100 ppm/K ± 200 ppm/K ±1% ± 5 %; ± 2 % 01 02 03 20 10 16 PACKAGING PACKAGING CODE MODEL TAPE WIDTH DIAMETER PITCH PIECES/REEL BLISTER TAPE PART NUMBER PRODUCT DESCRIPTION CRA12 E 04 8 mm 180 mm/7" 4 mm 2000 TR RB8 CRA12 E 08 CRA12 S 08 CRA12 E 10 CRA12 S 10 12 mm 180 mm/7" 330 mm/13" 8 mm 2000 5000 TR TL RB8 RD7 CRA12 E 16 24 mm 330 mm/13" 8 mm 2000 5000 TR TL RB8 RD7 CIRCUIT 02 Circuit 01 Circuit Pin 1 4 pin 8 pin 10 pin 16 pin Pin 1 4 pin 03 Circuit 4 pin Document Number: 31003 Revision: 08-Feb-07 8 pin 10 pin 8 pin 10 pin 20 Circuit 16 pin Pin 1 For technical questions, contact: ff3aresistors@vishay.com www.vishay.com 261 CRA12E & S Thick Film Resistor Array Rated Power in % Vishay 120 100 80 60 40 20 0 - 55 - 25 0 25 Derating 50 75 70 100 125 150 175 Ambient Temperature in °C DIMENSIONS 8 -Terminal device S-Version E-Version 1 103 103 PIN 1 e MODEL a a e DIMENSIONS [in millimeters] PIN NO# L A A* B B* P T W CRA12E 4 2.54 0.79 - 0.51 0.38 1.27 0.53 3.05 CRA12E 8 5.08 0.79 - 0.51 0.38 1.27 0.53 3.05 CRA12S 8 5.08 0.79 0.89 0.51 0.38 1.27 0.53 3.05 CRA12E 10 6.40 0.79 - 0.51 0.38 1.27 0.53 3.05 CRA12S 10 6.40 0.79 0.89 0.51 0.38 1.27 0.53 3.05 CRA12E 16 10.30 0.79 - 0.51 0.38 1.27 0.53 3.05 Tol - 0.15 - 0.15 - 0.15 - 0.25 - 0.2 - 0.1 - 0.1 - 0.15 www.vishay.com 262 SOLDER PAD DIMENSIONS [in millimeters] c w d p a b e WAVE 2.2 4.3 0.57 1.27 0.71 1.05 1.09 REFLOW 2.2 3.9 0.57 1.27 0.71 0.86 1.09 The dimensions shown are for 8 pin part. For parts with different pin numbers use the same pitch and add or substract pads as required. For technical questions, contact: ff3aresistors@vishay.com Document Number: 31003 Revision: 08-Feb-07 CRA12E & S Thick Film Resistor Array Vishay TEST PROCEDURES AND REQUIREMENTS EN 60115-1 REQUIREMENTS1) TEST (clause) CONDITIONS OF TEST stability for product types: STABILITY CLASS 1 OR BETTER STABILITY CLASS 2 OR BETTER 10 Ω to 1 MΩ 10 Ω to 1 MΩ ±1% ± 2 %; ± 5 % ± 100 ppm/K ± 200 ppm/K ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) CRA12E/CRA12S Resistance (4.5) - Temperature coefficient (4.8.4.2) 20/- 55/20 °C and 20/125/20 °C Overload (4.13) U = 2.5 × (P70 x R)1/2 ≤ 2 x Umax; 1 s Solderability (4.17.5)2) Aging 4 h at 155 °C, dryheat Solder bath method; 235 °C; 1 s Visual examination Resistance to soldering heat (4.18.2) Solder bath method; (260 ± 5) °C; (10 ± 1) s ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) Rapid change of temperature (4.19) 30 min. at LCT = - 55 °C; 30 min. at UCT = 125 °C; 5 cycles ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) Damp heat, steady state (4.24) (40 ± 2) °C; 56 days; (93 ± 3) % RH ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) Climatic sequence (4.23) 16 h at UCT = 125 °C; 1 cycle at 55 °C; 2 h at LCT = - 55 °C; 1 h/1 kPa at 15 °C to 35 °C; 5 cycles at 55 °C U = (P70 x R)1/2 U = Umax; whichever is less severe ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) Endurance at 70 °C (4.25.1) U = (P70 x R)1/2 U = Umax; whichever is less severe 1.5 h on; 0.5 h off; 70 °C; 1000 h ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) Extended endurance (4.25.1.8) Duration extended to 8000 hours ± (2 % R + 0.1 Ω) ± (4 % R + 0.1 Ω) Endurance at upper category temperature (4.25.3) UCT = 125 °C; 1000 h ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) Good tinning (≥ 95 % covered) no visible damage Notes 1. Figures are given for a single element. 2. Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years. APPLICABLE SPECIFICATIONS • EN 60115-1 Generic Specification • EN 140400 Sectional Specification • EN 140401-802 Detail Specification • IEC 60068-2-X Variety of environmental test procedures • EIA 481 Packaging of SMD components Document Number: 31003 Revision: 08-Feb-07 For technical questions, contact: ff3aresistors@vishay.com www.vishay.com 263 Legal Disclaimer Notice Vishay Notice Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc., or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Vishay for any damages resulting from such improper use or sale. Document Number: 91000 Revision: 08-Apr-05 www.vishay.com 1