CRCW0201 e3
www.vishay.com
Vishay
Lead (Pb)-Free Commodity Thick Film Chip Resistors
FEATURES
• High volume product suitable for commercial
applications
• Pure tin solder contacts on Ni barrier layer
provides compatibility with lead (Pb)-free and
lead containing soldering processes
• Metal glaze on high quality ceramic
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
CASE
SIZE
INCH
CASE
SIZE
METRIC
POWER RATING
P70
W
LIMITING
ELEMENT
VOLTAGE
Umax.
ACRMS/DC
V
TEMPERATURE
COEFFICIENT
ppm/K
TOLERANCE
%
RESISTANCE
RANGE
Ω
± 100
± 200
0.05
CRCW0201
0201
30
SERIES
47.0 to 1M
±1
10.0 to 10M
-200 / +400
E24; E96
1.0 to 9.76
RR 0603M
± 200
10.0 to 10M
±5
E24
-200 / +400
1.0 to 9.1
Zero-ohm-resistor: Rmax. = 50 mΩ, Imax. at 70 °C = 1.0 A
Notes
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime
• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
CRCW0201
W
0.05
Operating Voltage Umax. ACRMS/DC
V
30
Insulation Voltage Uins (1 min)
V
50
Insulation Resistance
Ω
> 109
Operating Temperature Range
°C
-55 to +155
Weight
mg
0.17
Rated Dissipation at 70 °C
(1)
Note
(1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded
Revision: 21-Sep-2022
Document Number: 20052
1
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW0201 e3
www.vishay.com
Vishay
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: CRCW02011K00FNED
C
R
C
W
0
2
0
1
1
K
0
0
F
K
E
D
MODEL
VALUE
TOLERANCE
TCR
PACKAGING
CRCW0201
R = decimal
K = thousand
M = million
0000 = jumper
F = ± 1.0 %
J = ± 5.0 %
Z = jumper
K = ± 100 ppm/K
N = ± 200 ppm/K
X = -200 ppm/K / +400 ppm/K
0 = jumper
ED
EE
EI
Product Description: CRCW0201 100 1K0 1 % ET7 e3
CRCW0201
100
562R
1%
ET7
e3
MODEL
TCR
RESISTANCE
VALUE
TOLERANCE
VALUE
PACKAGING
LEAD (Pb)-FREE
CRCW0201
± 200 ppm/K
± 100 ppm/K
- 200 / + 400 ppm/K
1R0 = 1 Ω
10R = 10 Ω
10K = 10 kΩ
1M = 1 MΩ
0R0 = jumper
±1%
±5%
ET2
ET7
EF4
e3 = pure tin
termination finish
PITCH
REEL DIAMETER
PACKAGING
MODEL
CODE
QUANTITY
ED = ET7
10 000
CRCW0201
EI = ET2
20 000
EE = EF4
50 000
CARRIER TAPE
WIDTH
180 mm / 7"
Paper tape according
to IEC 60068-3 type I
8 mm
2 mm
254 mm / 10"
330 mm / 13"
DIMENSIONS in millimeters
L
T2
a
T1
SIZE
b
l
W
H
DIMENSIONS
SOLDER PAD DIMENSIONS
INCH
METRIC
L
W
H
T1
T2
a
b
l
0201
0603
0.6 ± 0.03
0.3 ± 0.03
0.23 ± 0.03
0.15 ± 0.05
0.10 ± 0.05
0.28
0.43
0.23
Note
• No marking for 0201 size
Revision: 21-Sep-2022
Document Number: 20052
2
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW0201 e3
www.vishay.com
Vishay
DERATING
Axis Title
2nd line
P70 - Fraction of Rated Dissipation (%)
10000
100
1st line
2nd line
1000
50
100
10
0
-60
-50
-40
-20
0
20
40
50
60
80
70
ϑamb - Ambient Temperature (°C)
100
120
140 150
160
TEST PROCEDURES AND REQUIREMENTS
REQUIREMENTS
PERMISSIBLE CHANGE (ΔR)
IEC
60068-2
TEST
METHOD
TEST
4.5
-
Resistance
-
± 1 %; ± 5 %
4.7
-
Voltage proof
U = 1.4 x Uins; 60 s
No flashover or breakdown
Solder bath method;
Sn60Pb40
non activated flux;
(235 ± 5) °C
(2 ± 0.2) s
Good tinning (≥ 95 % covered)
no visible damage
Solder bath method;
Sn96.5Ag3Cu0.5
non-activated flux;
(245 ± 5) °C
(3 ± 0.3) s
Good tinning (≥ 95 % covered)
no visible damage
± 100 ppm/K,
± 200 ppm/K,
-200 ppm/K / +400 ppm/K
EN 60115-1
CLAUSE
4.13
58 (Td)
4.33
4.19
Stability for product types:
CRCW0201 e3
Solderability
1 Ω to 10 MΩ
-
Temperature coefficient
(20 / -55 / 20) °C and
(20 / 125 / 20) °C
21 (Uu3)
Shear (adhesion)
9N
No visible damage
Depth 2 mm; 3 times
No visible damage,
no open circuit in bent position
± (0.5 % R + 0.05 Ω)
4.8.4.2
4.32
PROCEDURE
21 (Uu1)
Substrate bending
14 (Na)
Rapid change
of temperature
4.23
-
30 min. at -55 °C;
30 min. at 125 °C
Climatic sequence:
5 cycles
± (0.5 % R + 0.05 Ω)
1000 cycles
± (1 % R + 0.05 Ω)
-
4.23.2
2 (Ba)
Dry heat
125 °C; 16 h
4.23.3
30 (Db)
Damp heat, cyclic
55 °C; ≥ 90 % RH; 24 h; 1 cycle
4.23.4
1 (Aa)
Cold
-55 °C; 2 h
4.23.5
13 (M)
Low air pressure
1 kPa; (25 ± 10) °C; 1 h
4.23.6
30 (Db)
Damp heat, cyclic
55 °C; ≥ 90 % RH; 24 h; 5 cycles
4.23.7
-
DC load
U=
± (2 % R + 0.1 Ω)
P 70 x R ≤ Umax.
U = P 70 x R ≤ Umax.;
1.5 h on; 0.5 h off;
4.25.1
Revision: 21-Sep-2022
-
Endurance at 70 °C
70 °C; 1000 h
± (2 % R + 0.1 Ω)
70 °C; 8000 h
± (4 % R + 0.1 Ω)
Document Number: 20052
3
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW0201 e3
www.vishay.com
Vishay
TEST PROCEDURES AND REQUIREMENTS
REQUIREMENTS
PERMISSIBLE CHANGE (ΔR)
IEC
60068-2
TEST
METHOD
TEST
58 (Td)
Resistance to
soldering heat
Solder bath method
(260 ± 5) °C; (10 ± 1) s
± (1 % R + 0.05 Ω)
4.35
-
Flammability,
needle flame test
IEC 60695-11-5;
10 s
No burning after 30 s
4.24
78 (Cab)
Damp heat, steady state
(40 ± 2) °C; (93 ± 3) % RH; 56 days
± (2 % R + 0.1 Ω)
-
Endurance at upper
category temperature
155 °C, 1000 h
± (2 % R + 0.1 Ω)
4.29
45 (XA)
Component
solvent resistance
Isopropyl alcohol;
50 °C; method 2
No visible damage
4.22
6 (Fc)
Vibration, endurance
by sweeping
f = 10 Hz to 2000 Hz;
x, y, z ≤ 1.5 mm;
A ≤ 200 m/s2;
10 sweeps per axis
± (0.5 % R + 0.05 Ω)
EN 60115-1
CLAUSE
4.18.2
4.25.3
PROCEDURE
Stability for product types:
CRCW0201 e3
1 Ω to 10 MΩ
All tests are carried out in accordance with the following specifications:
• EN 60115-1, generic specification
• EN 140400, sectional specification
• EN 140401-802, detail specification
• IEC 60068-2-x, environmental test procedures
Packaging of components is done in paper tapes according to IEC 60286-3.
Revision: 21-Sep-2022
Document Number: 20052
4
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2023 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 01-Jan-2023
1
Document Number: 91000
