D/CRCW-HR
www.vishay.com
Vishay
Lead (Pb)-Bearing Thick Film,
Rectangular High Value Chip Resistor
FEATURES
• High resistance values (up to 470M)
• Suitable for voltage dividers and hybrids
• Lead (Pb)-bearing termination plating on Ni barrier layer
• Metal glaze on high quality ceramic
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
CASE
SIZE
INCH
CASE
SIZE
METRIC
POWER
RATING
P70
W
LIMITING
ELEMENT
VOLTAGE
Umax.
ACRMS/DC
V
TEMPERATURE
COEFFICIENT
ppm/K
TOLERANCE
%
RESISTANCE
RANGE
Ω
SERIES
D11/CRCW0603-HR
0603
RR 1608M
0.10
75
± 500
±5
11M to 470M
E24
D12/CRCW0805-HR
0805
RR 2012M
0.125
150
± 500
±5
11M to 470M
E24
D25/CRCW1206-HR
1206
RR 3216M
0.25
200
± 500
±5
11M to 470M
E24
Notes
• These resistors do not feature a limited lifetime when operated within the limits of rated dissipation, permissible operating voltage, and
permissible film temperature. However, the resistance typically increase due to the resistor’s film temperature over operating time, generally
known as drift. The drift may exceed the stability requirements of an individual application circuit and thereby limits the functional time
• Marking and packaging: see datasheet “Surface Mount Resistor Marking” (www.vishay.com/doc?20020)
• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
D11/CRCW0603-HR
D12/CRCW0805-HR
D25/CRCW1206-HR
Rated dissipation at P70 (1)
W
0.1
0.125
0.25
Operating voltage Umax. ACRMS/DC
V
75
150
200
Voltage coefficient (2)
< 100M: < 0.1 ppm/V
> 100M: < 0.3 ppm/V
%/V
Insulation voltage Uins (1 min)
V
Insulation resistance
Ω
Operating temperature range
°C
Weight
mg
100
200
300
> 109
- 55 to + 155
2
5.5
10
Notes
(1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded
(2) Voltage coefficient was tested according to 10 V measurements
Revision: 06-Dec-2023
Document Number: 20011
1
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW-HR
www.vishay.com
Vishay
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: CRCW060316M0JPTAHR
C
R
C
W
0
6
0
3
1
6
M
0
J
P
T
A
H
R
MODEL / SIZE
RESISTANCE
TOLERANCE
TCR
PACKAGING
SPECIAL
CRCW0603
CRCW0805
CRCW1206
M = million
J=±5%
P = ± 500 ppm/K
TA, TC
Up to 2 digits
HR = high value
Product Description: CRCW0603-HR 500 16M 5% RT1
CRCW0603-HR
500
16M
J
RT1
MODEL
TCR
RESISTANCE
TOLERANCE
PACKAGING
CRCW0603-HR
CRCW0805-HR
CRCW1206-HR
± 500 ppm/K
68M = 68 MΩ
220M = 220 MΩ
±5%
RT1, RT6
PACKAGING
MODEL
CODE
CRCW0603-HR
CRCW0805-HR
CRCW1206-HR
QUANTITY
TA = RT1
5000
TC = RT6
20 000
TA = RT1
5000
TC = RT6
20 000
TA = RT1
5000
TC = RT6
20 000
CARRIER TAPE
Paper tape acc.
to IEC 60068-3
Type I
WIDTH
PITCH
8 mm
4 mm
8 mm
4 mm
8 mm
4 mm
REEL DIAMETER
180 mm/7"
330 mm/13"
180 mm/7"
330 mm/13"
180 mm/7"
330 mm/13"
DIMENSIONS
L
T2
b
I
W
H
a
T1
SIZE
SOLDER PAD DIMENSIONS in millimeters
DIMENSIONS in millimeters
INCH METRIC
L
REFLOW SOLDERING
H
T1
T2
a
b
l
a
b
l
0.3 ± 0.2
0.5
0.9
1.0
0.9
0.9
1.0
0.3 ± 0.2
0.7
1.3
1.2
0.9
1.3
1.3
0.4 ± 0.2
0.9
1.7
2.0
1.1
1.7
2.3
0603
1608
1.55
+ 0.10
- 0.05
0.85 ± 0.1
0.45 ± 0.05
0.3 ± 0.2
0805
2012
2.0
+ 0.20
- 0.10
1.25 ± 0.15
0.5 ± 0.10
0.3
1206
3216
3.2
+ 0.10
- 0.20
1.6 ± 0.15
0.55 ± 0.05
0.45 ± 0.2
Revision: 06-Dec-2023
WAVE SOLDERING
W
+ 0.20
- 0.10
Document Number: 20011
2
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW-HR
www.vishay.com
Vishay
Fraction of Rated Dissipation P70
DERATING
100
%
50
0
- 50
0
50
100
°C
150
70
Ambient Temperature in amb
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
IEC
60068-2
TEST
METHOD
TEST
PROCEDURE
REQUIREMENTS
PERMISSIBLE CHANGE (ΔR)
STABILITY CLASS 2 OR BETTER
Stability for product types:
D/CRCW-HR
4.5
_
11 MΩ to 470 MΩ
Resistance
-
±5%
_
Short time overload
U = 2.5 x √P70 x R ≤ 2 x Umax.;
Duration acc. to style
± (0.5 % R + 0.05 Ω)
4.17.2
58 (Td)
Solderability
Solder bath method;
Sn60Pb40
Good tinning (≥ 95 % covered); no visible
damage
4.8.4.2
_
Temperature
coefficient
20 °C/-55 °C/20 °C and
20 °C/125 °/20 °C
± 500 ppm/K
4.32
21 (Uu3)
Shear (adhesion)
RR 1608: 9 N
RR 2012 and RR 3216: 45 N
No visible damage
4.33
21 (Uu1)
Substrate bending
Depth 2 mm;
3 times
No visible damage, no open circuit in bent
position
± (0.25 % R + 0.05 Ω)
4.19
14 (Na)
Rapid change of
temperature
4.23
4.23.2
4.23.3
_
2 (Ba)
30 (Db)
4.23.4
4.23.5
4.23.6
1 (Aa)
13 (M)
30 (Db)
4.23.7
_
4.25.1
_
4.13
Revision: 06-Dec-2023
Climatic sequence:
Dry heat
Damp heat, cyclic
Cold
Low air pressure
Damp heat, cyclic
D.C. load
Endurance at
70 °C
30 min. at -55 °C;
30 min. at 125 °C
5 cycles
1000 cycles
125 °C; 16 h
55 °C; ≥ 90 % RH;
24 h; 1 cycle
-55 °C; 2 h
1 kPa; (25 ± 10) °C; 1 h
55 °C; ≥ 90 % RH
24 h; 5 cycle
U = √P70 x R
U = √P70 x R ≤ Umax.
1.5 h on; 0.5 h off;
70 °C; 1000 h
70 °C; 8000 h
± (0.5 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (2 % R + 0.1 Ω)
± (2 % R + 0.1 Ω)
± (4 % R + 0.1 Ω)
Document Number: 20011
3
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW-HR
www.vishay.com
Vishay
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
IEC
60068-2
TEST
METHOD
TEST
PROCEDURE
REQUIREMENTS
PERMISSIBLE CHANGE (ΔR)
STABILITY CLASS 2 OR BETTER
Stability for product types:
D/CRCW-HR
4.18.2
4.24
4.25.3
11 MΩ to 470 MΩ
58 (Td)
Resistance to
soldering heat
Solder bath method
(260 ± 5) °C;
(10 ± 1) s
± (0.5 % R + 0.05 Ω)
78 (Cab)
Damp heat,
steady state
(40 ± 2) °C;
(93 ± 3) % RH; 56 days
± (2 % R + 0.1 Ω)
_
Endurance at upper
category temperature
155 °C; 1000 h
± (2 % R + 0.1 Ω)
All tests are carried out in accordance with the following specifications:
• EN 60115-1, generic specification
• EN 140400, sectional specification
• EN 140401-802, detail specification
• IEC 60068-2-x, variety of environmental test procedures
Packaging of components is done in paper or blister tapes according to IEC 60286-3.
Revision: 06-Dec-2023
Document Number: 20011
4
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2024 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Document Number: 91000
1
For technical questions, contact:
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Revision: 01-Jan-2024