CRCW0805470RJNEAIF

D/CRCW-IF e3 www.vishay.com Vishay Pulse Proof Thick Film Chip Resistors FEATURES • High pulse performance, up to 10 kW • High pulse voltage up to 4 kV, 1.2 μs / 50 μs • Stability at different environmental conditions R/R  1 % (1000 h rated power at 70 °C) • AEC-Q200 qualified • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 LINKS TO ADDITIONAL RESOURCES 3D 3D APPLICATIONS • DC-DC converters 3D Models • On-board chargers The pulse proof thick film chip resistor series is the perfect choice for high pulse load performance resistors. Typical applications include automotive DC-DC converters and on-board chargers, lighting ballasts, and storage drivers. • Lighting ballasts • Storage drivers TECHNICAL SPECIFICATIONS DESCRIPTION D10/CRCW0402-IFD11/CRCW0603-IFD12/CRCW0805-IFD25/CRCW1206-IFCRCW1210-IFCRCW2010-IFCRCW2512-IF e3 e3 e3 e3 e3 e3 e3 Imperial size Metric size code 0402 0603 0805 1206 1210 2010 2512 RR1005M RR1608M RR2012M RR3216M RR3225M RR5025M RR6332M Resistance range 1  to 100 k Resistance tolerance ± 10 %; ± 5 % Temperature coefficient ± 200 ppm/K Rated dissipation, P70 (1) 0.063 W 0.10 W 0.125 W 0.25 W 0.50 W 0.75 W 1.0 W Operating voltage, Umax. ACRMS/DC 50 V 75 V 150 V 200 V 200 V 400 V 500 V 300 V 300 V 300 V Permissible film temperature, 155 °C F max. (1) Operating temperature range -55 °C to +155 °C Max. resistance change at P70 for resistance range, IR/RI after: 1000 h  1.0 % 8000 h  2.0 % Permissible voltage against ambient (insulation): 1 min, Uins 75 V 100 V Failure rate: FITobserved 200 V 300 V  0.1 x 10-9/h Note (1) Please refer to “Application Information” below Revision: 09-Sep-2021 Document Number: 20024 1 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com Vishay APPLICATION INFORMATION When the resistor dissipates power, a temperature rise above the ambient temperature occurs, dependent on the thermal resistance of the assembled resistor together with the printed circuit board. The rated dissipation applies only if the permitted film temperature is not exceeded. These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime. TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE / SIZE TCR D10/CRCW0402-IF e3 ± 200 ppm/K D11/CRCW0603-IF e3 ± 200 ppm/K D12/CRCW0805-IF e3 ± 200 ppm/K D25/CRCW1206-IF e3 ± 200 ppm/K CRCW1210-IF e3 ± 200 ppm/K CRCW2010-IF e3 ± 200 ppm/K CRCW2512-IF e3 ± 200 ppm/K TOLERANCE RESISTANCE E-SERIES ± 10 % 1.0  to 100 k E24 1.0  to 100 k E24 1.0  to 100 k E24 1.0  to 100 k E24 1.0  to 100 k E24 1.0  to 100 k E24 1.0  to 100 k E24 ±5% ± 10 % ±5% ± 10 % ±5% ± 10 % ±5% ± 10 % ±5% ± 10 % ±5% ± 10 % ±5% PACKAGING TYPE / SIZE D10/CRCW0402-IF e3 D11/CRCW0603-IF e3 D12/CRCW0805-IF e3 D25/CRCW1206-IF e3 CRCW1210-IF e3 CRCW2010-IF e3 CRCW2512-IF e3 Revision: 09-Sep-2021 CODE QUANTITY ED = ET7 10 000 EE = EF4 50 000 EI = ET2 5000 ED = ET3 10 000 EL = ET4 20 000 EE = ET8 50 000 EA = ET1 5000 EB = ET5 10 000 EC = ET6 20 000 EA = ET1 5000 EB = ET5 10 000 EC = ET6 20 000 EA = ET1 5000 EB = ET5 10 000 EC = ET6 20 000 EA = ET1 5000 EB = ET5 10 000 EC = ET6 20 000 EF = E02 4000 EG = E67 2000 EH = E82 4000 PACKAGING STYLE WIDTH PITCH 8 mm 2 mm PACKAGING DIMENSIONS Ø 180 mm / 7" Ø 330 mm / 13" Ø 180 mm / 7" 2 mm Ø 180 mm / 7" Ø 285 mm / 11.25" Ø 330 mm / 13" 8 mm Ø 180 mm / 7" 4 mm Ø 285 mm / 11.25" Ø 330 mm / 13" Paper tape according to IEC 60286-3, type 1a Ø 180 mm / 7" 8 mm 4 mm Ø 285 mm / 11.25" Ø 330 mm / 13" Ø 180 mm / 7" 8 mm 4 mm Ø 285 mm / 11.25" Ø 330 mm / 13" Ø 180 mm / 7" 8 mm 4 mm 12 mm 4 mm Ø 285 mm / 11.25" Ø 330 mm / 13" Blister tape according to IEC 60286-3 type 2a 12 mm 8 mm 4 mm Ø 180 mm / 7" Ø 180 mm / 7" Document Number: 20024 2 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com Vishay PART NUMBER AND PRODUCT DESCRIPTION Part Number: CRCW08051R00JNEAIF C R C W 0 8 0 5 1 R 0 0 J N E A I F TYPE VALUE TOLERANCE TCR PACKAGING SPECIAL CRCW0402 CRCW0603 CRCW0805 CRCW1206 CRCW1210 CRCW2010 CRCW2512 R = decimal K = thousand J=±5% K = ± 10 % N = ± 200 ppm/K EA, EB, EC, ED, EE, EF, EG, EH, EI, EL Up to 2 digits IF = pulse proof Product Description: D12/CRCW0805-IF 200 1R0 5 % ET1 e3 D12/CRCW0805-IF 200 1R0 5% ET1 e3 TYPE TCR RESISTANCE VALUE TOLERANCE PACKAGING LEAD (Pb)-FREE D10/CRCW0402-IF D11/CRCW0603-IF D12/CRCW0805-IF D25/CRCW1206-IF CRCW1210-IF CRCW2010-IF CRCW2512-IF ± 200 ppm/K 1R0 = 1  10K = 10 k ±5% ± 10 % ET1, ET2, ET3, ET4, ET5, ET6, ET7, ET8, EF4, E02, E67, E82 e3 = pure tin termination finish Revision: 09-Sep-2021 Document Number: 20024 3 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com DESCRIPTION Vishay • The Global Automotive Declarable Substance List (GADSL) (3) Production is strictly controlled and follows an extensive set of instructions established for reproducibility. A cermet film layer and a glass-over are deposited on a high grade (Al2O3) ceramic substrate with its prepared inner contacts. The resistor elements are covered by a protective coating designed for electrical, mechanical and climatic protection. The terminations receive a final pure tin on nickel plating.  The result of the determined production is verified by an extensive testing procedure on 100 % of the individual chip resistors. Only accepted products are laid directly into the tape in accordance with IEC 60286-3 Type 1a and Type 2a (1). The products do not contain any of the banned substances as per IEC 62474, GADSL, or the SVHC list, see www.vishay.com/how/leadfree. ASSEMBLY • 2011/65/EU Restriction of the Use of Hazardous Substances Directive (RoHS) with amendment 2015/863/EU The resistors are suitable for processing on automatic SMD assembly systems. They are suitable for automatic soldering using wave, reflow or vapor phase as shown in IEC 61760-1 (1). The encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters and aqueous solutions. The suitability of conformal coatings, potting compounds and their processes, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. The resistors are RoHS-compliant, the pure tin plating provides compatibility with lead (Pb)-free and lead-containing soldering processes. Solderability is specified for 2 years after production or requalification. The permitted storage time is 20 years. The immunity of the plating against tin whisker growth has been proven under extensive testing. MATERIALS Vishay acknowledges the following systems for the regulation of hazardous substances: • IEC 62474, Material Declaration for Products of and for the Electrotechnical Industry, with the list of declarable substances given therein (2) • The REACH regulation (1907/2006/EC) and the related list of substances with very high concern (SVHC) (4) for its supply chain Hence the products fully comply with the following directives: • 2000/53/EC End-of-Life Vehicle Directive (ELV) and Annex II (ELV II) • 2012/19/EU Waste Electrical and Electronic Equipment Directive (WEEE) Vishay pursues the elimination of conflict minerals from its supply chain, see the Conflict Minerals Policy at www.vishay.com/doc?49037. APPROVALS The resistors are qualified according to AEC-Q200. Where applicable, the resistors are tested in accordance with EN 140401-802 which refers to EN 60115-1, EN 60115-8 and the variety of environmental test procedures of the IEC 60068 (1) series. RELATED PRODUCTS For more information about pulse proof and high power products please refer to CRCW-HP e3, “Pulse Proof, High Power Thick Film Chip Resistors” datasheet (www.vishay.com/doc?20043) For anti-surge and high power products, please refer to RCS e3, “Anti-Surge, High Power Thick Film Chip Resistors” datasheet (www.vishay.com/doc?20065) Notes (1) The quoted IEC standards are also released as EN standards with the same number and identical contents (2) The IEC 62474 list of declarable substances is maintained in a dedicated database, which is available at http://std.iec.ch/iec62474 (3) The Global Automotive Declarable Substance List (GADSL) is maintained by the American Chemistry Council and available at www.gadsl.org (4) The SVHC list is maintained by the European Chemical Agency (ECHA) and available at http://echa.europa.eu/candidate-list-table Revision: 09-Sep-2021 Document Number: 20024 4 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com Vishay FUNCTIONAL PERFORMANCE Single Pulse Axis Title 100 000 1000 100 1000 1st line 2nd line 10 000 2nd line ^ Pmax. - Pulse Load (W) 10000 CRCW2512-IF CRCW2010-IF CRCW1210-IF D25/CRCW1206-IF D12/CRCW0805-IF D11/CRCW0603-IF D10/CRCW0402-IF 10 100 1 0.1 0.01 0.000001 10 0.00001 0.0001 0.001 0.01 0.1 1 10 100 ti - Pulse Duration (s) Maximum pulse load, single pulse; applicable if P  0 and n < 1000 and Uˆ = Uˆ max.; for permissible resistance change equivalent to 8000 h operation Continuous Pulse Axis Title 10000 CRCW2512-IF CRCW2010-IF CRCW1210-IF D25/CRCW1206-IF D12/CRCW0805-IF D11/CRCW0603-IF D10/CRCW0402-IF 10 000 1000 100 1000 1st line 2nd line 2nd line ^ Pmax. - Continuous Pulse Load (W) 100 000 10 100 1 0.1 0.01 0.000001 10 0.00001 0.0001 0.001 0.01 0.1 1 10 100 ti - Pulse Duration (s) Maximum pulse load, continuous pulses; applicable if P  P (amb) and Uˆ = Uˆ max.; for permissible resistance change equivalent to 8000 h operation Pulse Voltage Axis Title 2000 10000 CRCW2512-IF CRCW2010-IF D25/CRCW1206-IF, CRCW1210-IF D12/CRCW0805-IF D11/CRCW0603-IF D10/CRCW0402-IF 1800 1400 1000 1200 1st line 2nd line 2nd line ^ Umax. - Pulse Voltage (V) 1600 1000 800 100 600 400 200 0 0.000001 10 0.00001 0.0001 0.001 0.01 0.1 1 10 ti - Pulse Duration (s) Maximum pulse voltage, single and continuous pulses; applicable if Pˆ = Pˆ max.; for permissible resistance change equivalent to 8000 h operation Revision: 09-Sep-2021 Document Number: 20024 5 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com Vishay Derating Axis Title 1.2 1.0 0.8 1000 1st line 2nd line 2nd line P - Power Dissipation (W) 10000 CRCW2512-IF CRCW2010-IF CRCW1210-IF D25/CRCW1206-IF D12/CRCW0805-IF D11/CRCW0603-IF D10/CRCW0402-IF 0.6 100 0.4 0.2 10 0 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 ϑamb - Ambient Temperature (°C) 80 90 100 110 120 130 140 150 160 1.2 μs / 50 μs Pulse Axis Title 10 000 10000 CRCW2512-IF CRCW2010-IF CRCW1210-IF D25/CRCW1206-IF D12/CRCW0805-IF D11/CRCW0603-IF D10/CRCW0402-IF 1000 1st line 2nd line 2nd line Peak Voltage (V) 1000 100 100 10 1 1 10 100 1000 10 000 10 100 000 Resistance Value (Ω) Pulse load rating in accordance to EN 60115-1, 4.27; 1.2 μs / 50 μs; 5 pulses at 12 s intervals; for permissible resistance change 1 % 10 μs / 700 μs Pulse Axis Title 10 000 1000 1st line 2nd line 1000 2nd line Peak Voltage (V) 10000 CRCW2512-IF CRCW2010-IF CRCW1210-IF D25/CRCW1206-IF D12/CRCW0805-IF D11/CRCW0603-IF D10/CRCW0402-IF 100 100 10 1 1 10 100 1000 10 000 10 100 000 Resistance Value (Ω) Pulse load rating in accordance to EN 60115-1, 4.27; 10 μs / 700 μs; 10 pulses at 1 min intervals; for permissible resistance change 1 % Revision: 09-Sep-2021 Document Number: 20024 6 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com Vishay TESTS AND REQUIREMENTS All executed tests are carried out in accordance with the following specifications: The testing also covers most of the requirements specified by EIA/IS-703 and JIS-C-5201-1. EN 60115-1, generic specification The tests are carried out under standard atmospheric conditions in accordance with IEC 60068-1, 4.3, whereupon the following values are applied: EN 60115-8 specification (successor of EN 140400), sectional EN 140401-802, detail specification Temperature: 15 °C to 35 °C IEC 60068-2-xx, test methods Relative humidity: 25 % to 75 % The parameters stated in the Test Procedures and Requirements table are based on the required tests and permitted limits of EN 140401-802. The table presents only the most important tests, for the full test schedule refer to the documents listed above. However, some additional tests and a number of improvements against those minimum requirements have been included. Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar). A climatic category LCT / UCT / 56 is applied, defined by the lower category temperature (LCT), the upper category temperature (UCT), and the duration of exposure in the damp heat, steady state test (56 days). The components are mounted for testing on boards in accordance with EN 60115-8, 2.4.2 unless otherwise specified. TEST PROCEDURES AND REQUIREMENTS EN 60115-1 IEC 60068-2 (1) CLAUSE TEST METHOD PROCEDURE STABILITY CLASS 2 OR BETTER TEST Stability for product types: D/CRCW-IF e3 4.5 - 4.8 - REQUIREMENTS PERMISSIBLE CHANGE (R) 1  to 100 k Resistance - ± 5 %; ± 10 % Temperature coefficient At (20 / -55 / 20) °C and (20 / 125 / 20) °C ± 200 ppm/K U = P 70 x R  Umax. 1.5 h on; 0.5 h off 4.25.1 - Endurance at 70 °C - Endurance at upper category temperature 4.24 78 (Cab) 4.37 70 °C; 1000 h ± (1 % R + 0.05 ) 70 °C; 8000 h ± (2 % R + 0.1 ) 155 °C; 1000 h ± (1 % R + 0.05 ) Damp heat, steady state (40 ± 2) °C; (93 ± 3) % RH; 56 days ± (1 % R + 0.05 ) 67 (Cy) Damp heat, steady state, accelerated (85 ± 2) °C; (85 ± 5) % RH; U = 0.1 x P 85 x R ; U  100 V; 1000 h ± (1 % R + 0.05 ) 4.23 4.23.2 2 (Ba) Climatic sequence: Dry heat 125 °C; 16 h 4.23.3 30 (Db) Damp heat, cyclic 55 °C; 24 h;  90 % RH; 1 cycle 4.23.4 4.23.5 4.23.6 4.23.7 1 (Ab) 13 (M) 30 (Db) - Cold Low air pressure Damp heat, cyclic DC load -55 °C; 2 h 8.5 kPa; 2 h; (25 ± 10) °C 55 °C; 5 days; > 90 % RH; 5 cycles U = P 70 x R  Umax.; 1 min ± (1 % R + 0.05 ) 4.25.3 1 (Aa) Cold -55 °C; 2 h ± (0.25 % R + 0.05 ) 4.19 14 (Na) Rapid change of temperature ± (1 % R + 0.05 ) 4.13 - Short time overload 30 min. at -55 °C and 30 min. at 125 °C 1000 cycles U = 2.5 x  P 70 x R   2 x Umax.; whichever is the less severe; 5 s - Single pulse high voltage overload - 4.27 Revision: 09-Sep-2021 Severity no. 4: U = 10 x P 70 x R or U  2 x Umax.; whichever is the less severe; 10 pulses 10 μs / 700 μs ± (2 % R + 0.05 ) ± (1 % R + 0.05 ) Document Number: 20024 7 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com Vishay TEST PROCEDURES AND REQUIREMENTS EN 60115-1 IEC 60068-2 (1) CLAUSE TEST METHOD PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (R) STABILITY CLASS 2 OR BETTER TEST Stability for product types: 1  to 100 k D/CRCW-IF e3 4.39 - Periodic electric overload U = 15 x P 70 x R U  2 x Umax.; whichever is the less severe; 0.1 s on; 2.5 s off; 1000 cycles ± (1 % R + 0.05 ) no visible damage 4.38 - Electrostatic discharge (human body model) IEC 61340-3-1 (1); 3 positive + 3 negative discharges; ESD voltage according to the size ± (1 % R + 0.05 ) Vibration Endurance by sweeping; 10 Hz to 2000 Hz; no resonance; amplitude  1.5 mm or  200 m/s2; 7.5 h ± (0.25 % R + 0.05 ) no visible damage 4.22 6 (Fc) Good tinning ( 95 % covered); no visible damage 4.17 58 (Td) 4.18 58 (Td) 4.29 45 (XA) 4.32 21 (Ue3) Shear (adhesion) 4.33 21 (Ue1) Substrate bending Depth 2 mm; 3 times ± (0.25 % R + 0.05 ) no visible damage, no open circuit in bent position 4.7 - Voltage proof U = 1.4 x Uins; 60 s No flashover or breakdown - Flammability, needle flame test IEC 60695-11-5 (1); 10 s No burning after 30 s 4.35 Solderability Solder bath method, Sn60Pb40; non-activated flux (235 ± 5) °C; (2 ± 0.2) s Solder bath method, Sn96.5Ag3Cu0.5 or Sn99.3Cu0.7; non-activated flux (245 ± 5) °C or (250 ± 5) °C; (3 ± 0.3) s Soldering bath method; (260 ± 5) °C; (10 ± 1) s Isopropyl alcohol; +50 °C; method 2 CRCW0402-IF: 9 N CRCW0603-IF to CRCW2512-IF: 17.7 N Resistance to soldering heat Component solvent resistance ± (0.25 % R + 0.05 ) No visible damage No visible damage Note (1) The quoted IEC standards are also released as EN standards with the same number and identical contents Revision: 09-Sep-2021 Document Number: 20024 8 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-IF e3 www.vishay.com Vishay DIMENSIONS L T2 W H T1 DIMENSIONS AND MASS L (mm) W (mm) H (mm) T1 (mm) T2 (mm) MASS (mg) D10/CRCW0402-IF e3 1.0 ± 0.05 0.5 ± 0.05 0.35 ± 0.05 0.25 ± 0.05 0.2 ± 0.10 0.65 D11/CRCW0603-IF e3 1.55 + 0.10 / - 0.05 0.85 ± 0.1 0.45 ± 0.05 0.3 ± 0.20 0.3 ± 0.20 2 D12/CRCW0805-IF e3 2.0 + 0.20 / - 0.10 1.25 ± 0.15 0.45 ± 0.05 0.3 + 0.20 / - 0.10 0.3 ± 0.20 5.5 D25/CRCW1206-IF e3 TYPE / SIZE 3.2 + 0.10 / - 0.20 1.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.20 0.4 ± 0.20 10 CRCW1210-IF e3 3.2 ± 0.20 2.5 ± 0.2 0.55 ± 0.05 0.45 ± 0.20 0.4 ± 0.20 16 CRCW2010-IF e3 5.0 ± 0.15 2.5 ± 0.15 0.6 ± 0.10 0.6 ± 0.20 0.6 ± 0.20 25.5 CRCW2512-IF e3 6.3 ± 0.20 3.15 ± 0.15 0.6 ± 0.10 0.6 ± 0.20 0.6 ± 0.20 40.5 SOLDER PAD DIMENSIONS X G Y Z RECOMMENDED SOLDER PAD DIMENSIONS WAVE SOLDERING TYPE / SIZE REFLOW SOLDERING G (mm) Y (mm) X (mm) Z (mm) G (mm) Y (mm) X (mm) Z (mm) D10/CRCW0402-IF e3 - - - - 0.45 0.60 0.60 1.65 D11/CRCW0603-IF e3 0.65 1.10 1.25 2.85 0.75 0.75 1.00 2.25 D12/CRCW0805-IF e3 0.90 1.30 1.60 3.50 1.00 0.95 1.45 2.90 D25/CRCW1206-IF e3 1.40 1.40 1.95 4.20 1.50 1.05 1.80 3.60 CRCW1210-IF e3 1.80 1.45 2.95 4.70 1.70 1.10 2.80 3.90 CRCW2010-IF e3 3.40 1.65 2.85 6.70 3.50 1.45 2.80 6.40 CRCW2512-IF e3 4.60 1.60 3.65 7.80 4.75 1.45 3.50 7.65 Note • The rated dissipation applies only if the permitted film temperature is not exceeded. Furthermore, a high level of ambient temperature or of power dissipation may raise the temperature of the solder joint, hence special solder alloys or board materials may be required to maintain the reliability of the assembly. The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g. in standards IEC 61188-5-x or in publication IPC-7351. They do not guarantee any supposed thermal properties, particularly as these are also strongly influenced by many other parameters. Still, the given solder pad dimensions will be found adequate for most general applications Revision: 09-Sep-2021 Document Number: 20024 9 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 09-Jul-2021 1 Document Number: 91000