CTR20001FFKGANHWS

CTR www.vishay.com Vishay Electro-Films Thin Film, Center-Tapped Resistor Divider Network FEATURES • • • • • • • Wire bondable Center tap feature Tight ratio tolerances to: 0.05 % Chip size: 0.030" x 0.030" Case: 0303 Resistance range total: 10  to 1 M Oxidized silicon substrate for good power dissipation • Moisture resistant • Resistor material: tantalum nitride, self-passivating • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 Product may not be to scale LINKS TO ADDITIONAL RESOURCES 3D 3D I V 3D Models The CTR series is a center-tapped resistor chip combining excellent stability with 250 mW power levels. The CTR offers the designer flexibility in use as either a single value resistor as two resistors with a center tap feature. The CTR’s six bonding pads allows the user increased layout flexibility. The CTRs are manufactured using Vishay Electro-Films (EFI) sophisticated thin film equipment and manufacturing technology. The CTRs are 100 % electrically tested and visually inspected to MIL-STD-883, method 2032 class H or K. RB RA V I V APPLICATIONS Vishay EFI CTR center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, high power and tracking between two resistors is critical.  For low values, the resistance of the six bonding-pad configurations can vary, depending on the method of measurement used. Vishay EFI measures low-value resistors by the four wire Kelvin technique. The method illustrated above is critical for resistors of less than 100 . TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES PARAMETER Total Resistance Range Standard Tolerances TCR VALUE 10 to 1M ± 0.1, ± 0.5 ± 25, ± 50, ± 100 UNIT  % ppm/°C Tightest Standard Tolerance Available 0.1 % 0.5 % ± 25 ppm/°C ± 50 ppm/°C ± 100 ppm/°C 10 : 25 : 100 : 360 k: 620 k: 1 M: STANDARD ELECTRICAL SPECIFICATIONS PARAMETER TCR Tracking Between Halves (RA/RB) (1) Center Tap Ratio, RA/RB: Tolerance Noise, MIL-STD-202, Method 308, < 100  or > 251 k Moisture Resistance, MIL-STD-202, Method 106 Stability, 1000 h, +125 °C, 125 mW Operating Temperature Range Thermal Shock, MIL-STD-202, Method 107, Test Condition F High Temperature Exposure, +150 °C, 100 h Dielectric Voltage Breakdown Insulation Resistance Operating Voltage DC Power Rating at 70 °C (derated to Zero at +175 °C) 5x Rated Power Short-Time Overload, +25 °C, 5 s Note (1) 5 ppm/°C for R < 100. 20 ppm/°C for R < 20 Revision: 26-Oct-2020 VALUE ±2 1 ± 1 standard -20 typ. ± 0.5 max. R/R ± 0.2 max. absolute -55 to +150 ± 0.1 max. R/R ± 0.2 max. R/R 200 1012 min. 100 max. 0.25 max. ± 0.1 max. R/R UNIT ppm/°C % dB % % °C % % V  V W % Document Number: 61020 1 For technical questions, contact: efi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CTR www.vishay.com Vishay Electro-Films DIMENSIONS in inches 0.030 RA STANDARD CONFIGURATION Six locations. All pads 0.005" x 0.005" RB 0.026 0.030 TYPICAL RANGE 27 : to 99 : TYPICAL RANGE 10 : to 26.9 : TYPICAL RANGE 100 : to 1 M: SCHEMATIC R T = RA + RB RA RB MECHANICAL SPECIFICATIONS PARAMETER Chip Size Chip Thickness Chip Substrate Material Resistor Material Bonding Pad Size Number of Pads Pad Material Backing VALUE 0.030" x 0.030" ± 0.002" (0.762 mm x 0.762 mm ± 0.05 mm) 0.010" ± 0.002" (0.254 mm ± 0.05 mm) Oxidized silicon, 10 kÅ minimum SiO2 Tantalum nitride, self-passivating 0.005" x 0.005" (0.127 mm x 0.127 mm) min. 6 10 kÅ minimum aluminum None, lapped semiconductor silicon GLOBAL PART NUMBER INFORMATION Global Part Number: CTR50000KFKKGNHWS Global Part Number Description: CTR 5K 10 %, RT 1 %, 100 ppm/°C, TC track 10, Au, no back metal, class H, WS C MODEL CTR T R RESISTANCE (R TOTAL) First 4 digits are significant figures of resistance Revision: 26-Oct-2020 5 0 0 RESISTANCE MULTIPLIER CODE TOL. CODE (%) C = 0.001 B = 0.01 A = 0.1 0=1 1 = 10 2 = 100 3 = 1000 B = 0.1 C = 0.25 D = 0.5 F = 1.0 G = 2.0 J = 5.0 K = 10 M = 20 0 RATIO TOL. 0 K TCR (ppm/°C) B = 0.1 E = ± 25 C = 0.25 C = ± 50 D = 0.5 K = ± 100 F = 1.0 M = ± 250 G = 2.0 J = 5.0 N = No F K K TC TRACK TERMINATION (ppm/°C) G=±2 J=±5 K = ± 10 N = No G = Au A = Al G BACK METAL N H VISUAL CLASS G = Au H = class H N = none K = class K W S PACKAGING CODE WS = waffle pack 100 min, 1 mult. Document Number: 61020 2 For technical questions, contact: efi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000