DG187AP

DG186/187/188 Vishay Siliconix High-Speed Drivers with SPDT JFET Switches FEATURES BENEFITS APPLICATIONS D Constant On-Resistance Over Entire Analog Range D Low Leakage D Low Crosstalk D Rad Hardness D D D D D D D D D D Low Distortion Eliminates Large Signal Errors High Precision High Bandwidth Capability Fault Protection Audio Switching Video Switching Sample/Hold Guidance and Control Systems Telemetry DESCRIPTION The DG186/187/188 are precision single-pole, double-throw (SPDT) analog switches designed to provide accurate switching of video and audio signals. This series is ideally suited for applications requiring a constant on-resistance over the entire analog range. on-resistance include audio switching, video switching, and data acquisition. To achieve fast and accurate switch performance, each device comprises two n-channel JFET transistors and a TTL compatible bipolar driver. The driver is designed to achieve break-before-make switching action, eliminating the inadvertent shorting between channels and the crosstalk which would result. In the on state, each switch conducts current equally well in either direction. In the off condition, the switches will block up to 20 V peak-to-peak, with feedthrough of less than –60 dB at 10 MHz. The major difference in the devices is the on-resistance (DG186—10 W, DG187—30 W, DG188—75 W). Reduced errors are achieved through low leakage current (ID(on) < 2 nA). Applications which benefit from the flat JFET FUNCTIONAL BLOCK DIAGRAM AND PIN CONFIGURATION NC 1 NC 2 D1 3 S1 Dual-In-Line Top View 4 NC 1 NC 2 14 NC 13 NC 12 D2 11 S2 14 NC 13 NC D1 3 12 D2 S1 4 IN 5 10 NC V+ 6 9 V–* VL 7 8 VR 11 S2 IN 5 10 NC V+ 6 9 V– 7 8 VR Flat Package Top View D1 S2 10 1 9 S1 NC 2 IN 8 7 3 4 Refer to JAN38510 Information, Military Section VL D2 V+ Metal Can Top View 5 V–* 6 VR VL *COMMON TO SUBSTRATE AND CASE TRUTH TABLE Logic SW1 0 OFF SW2 ON 1 ON OFF Logic “0” 0 v 0.8 V Logic “1” w 2.0 20V Document Number: 70033 S-52895—Rev. E, 16-Jun-97 www.vishay.com S FaxBack 408-970-5600 4-1 DG186/187/188 Vishay Siliconix ORDERING INFORMATION Temp Range Package Part Number DG186AA/883 10-Pin Metal Can DG187AA/883, JM38510/11105BIA DG188AA/883, JM38510/11106BIA DG186AP/883 –55 to 125_C DG187AP/883, JM38510/11105BCA 14-Pin Sidebraze DG188AP DG188AP/883, JM38510/11106BCA JM38510/11105BXA 14-Pin Flat Pack JM38510/11106BXA ABSOLUTE MAXIMUM RATINGS V+ to V– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Current (S or D) DG187, DG188 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA V+ to VD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 V Current (All Other Pins) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA VD to V– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 V Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65 to 150_C VD to VD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . "22 V Power Dissipationa VL to V– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V 10-Pin Metal Canb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450 mW VL to VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V 14-Pin Sidebrazec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 825 mW VL to VR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V 14-Pin Flat Packd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 900 mW Notes: a. All leads welded or soldered to PC Board. b. Derate 6 mW/_C above 75_C c. Derate 11 mW/_C above 75_C d. Derate 10 mW/_C above 75_C VIN to VR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V VR to V– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 V VR to VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 V Current (S or D) DG186 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mA SCHEMATIC DIAGRAM (TYPICAL CHANNEL) V+ VL S IN D VR V– FIGURE 1. www.vishay.com S FaxBack 408-970-5600 4-2 Document Number: 70033 S-52895—Rev. E, 16-Jun-97 DG186/187/188 Vishay Siliconix SPECIFICATIONSa For DG186 Test Conditions Unless Specified p Parameter Symbol V+ = 15 V, V– = –15 V, VL = 5 V VR = 0 V, VIN = 0.8 or 2 Vf Limits Tempb Mind Full –7.5 Typc Maxd Unit 15 V W Analog Switch Analog Signal Rangee Drain-Source On-Resistance VANALOG rDS(on) IS = –10 mA, VD = –7.5 V Room Full 7.5 10 20 VS = "10 V, VD = #10 V V+ = 10 V, V– = –20 V Room Hot 0.05 10 1000 VS = "7.5 V, VD = #7.5 V Room Hot 0.05 10 1000 VS = "10 V, VD = #10 V V+ = 10 V, V– = –20 V Room Hot 0.04 10 1000 VS = "7.5 V, VD = #7.5 V Room Hot 0.03 10 1000 Source Off Leakage Current IS(off) Drain Off Leakage Current ID(off) Channel On Leakage Current ID(on) VD = VS = "7.5 V Room Hot Saturation Drain Current IDSS 2 ms Pulse Duration Room 300 Input Current with Input Voltage High IINH VIN = 5 V Room Hot 55 See Switching Time Test Circuit f = 1 MHz f = 1 MHz, RL = 75 W ns pF dB Power Supplies Positive Supply Current I+ Room Negative Supply Current I– Room Logic Supply Current IL Reference Supply Current IR VIN = 0 V V, or 5 V 0.8 –3 mA Room Room 3.2 –2 Notes: a. Refer to PROCESS OPTION FLOWCHART. b. Room = 25_C, Full = as determined by the operating temperature suffix. c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. e. Guaranteed by design, not subject to production test. f. VIN = input voltage to perform proper function. Document Number: 70033 S-52895—Rev. E, 16-Jun-97 www.vishay.com S FaxBack 408-970-5600 4-3 DG186/187/188 Vishay Siliconix SPECIFICATIONSa For DG187 Test Conditions Unless Specified p Parameter Symbol V+ = 15 V, V– = –15 V, VL = 5 V VR = 0 V, VIN = 0.8 or 2 Vf Limits Tempb Mind Full –7.5 Typc Maxd Unit 15 V W Analog Switch Analog Signal Rangee VANALOG Drain-Source On-Resistance Source Off Leakage Current rDS(on) IS = –10 mA, VD = –7.5 V Room Full 22 30 60 VS = "10 V, VD = #10 V V+ = 10 V, V– = –20 V Room Hot 0.06 1 100 VS = "7.5 V, VD = #7.5 V Room Hot 0.13 1 100 VS = "10 V, VD = #10 V V+ = 10 V, V– = –20 V Room Hot 0.04 1 100 VS = "7.5 V, VD = #7.5 V Room Hot 0.03 1 100 IS(off) Drain Off Leakage Current ID(off) Channel On Leakage Current ID(on) VD = VS = "7.5 V Room Hot Input Current with Input Voltage High IINH VIN = 5 V Room Hot Input Current with Input Voltage Low IINL VIN = 0 V Full –2 –200 nA –0.02 Digital Input 50 f = 1 MHz f = 1 MHz, RL = 75 W pF dB Power Supplies Positive Supply Current I+ Negative Supply Current I– Logic Supply Current IL Reference Supply Current IR Room Room VIN = 0 V V, or 5 V 0.8 –3 mA Room Room 3.2 –2 Notes: a. Refer to PROCESS OPTION FLOWCHART. b. Room = 25_C, Full = as determined by the operating temperature suffix. c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. e. Guaranteed by design, not subject to production test. f. VIN = input voltage to perform proper function. www.vishay.com S FaxBack 408-970-5600 4-4 Document Number: 70033 S-52895—Rev. E, 16-Jun-97 DG186/187/188 Vishay Siliconix SPECIFICATIONSa For DG188 Test Conditions Unless Otherwise Specified Parameter Limits V+ = 15 V, V– = –15 V, VL = 5 V VR = 0 V, VIN = 0.8 or 2 Vf Tempb Mind VANALOG Full –10 rDS(on) IS = –10 mA, VD = –7.5 V Room Full 35 VS = "10 V, VD = #10 V V+ = 10 V, V– = –20 V Room Hot 0.05 1 100 VS = "10 V, VD = #10 V Room Hot 0.07 1 100 VS = "10 V, VD = #10 V V+ = 10 V, V– = –20 V Room Hot 0.04 1 100 VS = "10 V, VD = #10 V Room Hot 0.50 1 100 Symbol Typc Maxd Unit 15 V 75 150 W Analog Switch Analog Signal Rangee Drain-Source On-Resistance Source Off Leakage Current IS(off) Drain Off Leakage Current ID(off) Channel On Leakage Current ID(on) VD = VS = "10 V Room Hot Input Current with Input Voltage High IINH VIN = 5 V Room Hot Input Current with Input Voltage Low IINL VIN = 0 V Full –2 –200 nA –0.03 Digital Input 50 See Switching Time Test Circuit f = 1 MHz f = 1 MHz, RL = 75 W ns pF dB Power Supplies Positive Supply Current I+ Negative Supply Current I– Room Room 0.8 –3 VIN = 0 V V, or 5 V mA Logic Supply Current IL Room Reference Supply Current IR Room 3.2 –2 Notes: a. Refer to PROCESS OPTION FLOWCHART. b. Room = 25_C, Full = as determined by the operating temperature suffix. c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. e. Guaranteed by design, not subject to production test. f. VIN = input voltage to perform proper function. Document Number: 70033 S-52895—Rev. E, 16-Jun-97 www.vishay.com S FaxBack 408-970-5600 4-5 DG186/187/188 Vishay Siliconix TYPICAL CHARACTERISTICS (25_C UNLESS NOTED) Supply Current vs. Temperature IIN vs. VIN and Temperature 100 5 VINL = 0 VINH = 5 V 80 IL 3 I IN (mA) I L , I–, I+, I R (mA) 4 –I– 2 –IINL 60 40 –IR 1 20 I+ IINH 0 –55 –35 –15 5 25 45 65 85 105 0 –55 –35 125 –15 5 Temperature (_C) 45 65 85 105 125 Temperature (_C) rDS(on) vs. Temperature Switching Time vs. VD and Temperature (DG186) 100 230 VD = 7.5 V DG188 210 tON VD = –7.5 V 190 t ON, t OFF (ns) DG187 r DS(on) ( W ) 25 10 DG186 170 tOFF 150 130 VD= –7.5 V IS = –10 mA 110 1 –50 –25 0 25 50 75 100 90 –55 125 –35 –15 5 Temperature (_C) 25 45 65 85 105 125 Temperature (_C) Leakage vs. Temperature (DG186) Switching Time vs. VD and Temperature (DG187/188) 130 100 V+ = 10 V V– = –20 V VL = 5 V VR = 0 VD = 7.5 V 120 VD = –7.5 V 110 t ON, t OFF (ns) I S, I D (nA) 10 IS(off) tON 100 90 tOFF 80 1 70 ID(on) ID(off) 60 0.1 25 45 65 85 Temperature (_C) www.vishay.com S FaxBack 408-970-5600 4-6 105 125 50 –55 –35 –15 5 25 45 65 85 105 125 Temperature (_C) Document Number: 70033 S-52895—Rev. E, 16-Jun-97 DG186/187/188 Vishay Siliconix TYPICAL CHARACTERISTICS (25_C UNLESS NOTED) ID(off) vs. Temperature (DG187/188) Capacitance vs. VD or VS (DG186) 30 100 f = 1 MHz V+ = 10 V, V– = –20 V VD = –10 V, VS = 10 V 26 C S, D (pF) I D (nA) 10 B Suffix 1 CS(off) 22 CD(on) 18 A Suffix CD(off) 14 0.1 10 25 45 65 85 Temperature (_C) 105 125 –8 Capacitance vs. VD or VS (DG187/188) 100 VINL = 0.8 V VINH = 2 V f = 1 MHz 90 80 CD(on) 14 70 12 60 ISO (dB) C S, D (pF) 16 10 CS(off) 8 DG186 50 30 V+ = 15 V, V– = –15 V VR = 0, VL = 5 V RL = 75 W VIN w 220 mVRMS 20 4 0 –10 DG187/188 40 CD(off) 6 2 8 Off Isolation vs. Frequency 20 18 –4 0 4 VD or VS – Drain or Source Voltage (V) Capacitance is measured from test terminal to common. 10 0 –8 –6 –4 –2 0 2 4 6 VD or VS – Drain or Source Voltage (V) Document Number: 70033 S-52895—Rev. E, 16-Jun-97 8 10 105 106 107 108 f – Frequency (Hz) www.vishay.com S FaxBack 408-970-5600 4-7 DG186/187/188 Vishay Siliconix TEST CIRCUITS Feedthrough due to charge injection may result in spikes at the leading and trailing edge of the output waveform. +5 V +15 V tON: VS = 3 V tOFF: VS = –3 V VL VS1 VS2 Logic Input V+ S1 D1 S2 D2 tr