DG406DN-E3

DG406, DG407 www.vishay.com Vishay Siliconix 16-Ch/Dual 8-Ch High-Performance CMOS Analog Multiplexers DESCRIPTION FEATURES The DG406 is a 16 channel single-ended analog multiplexer designed to connect one of sixteen inputs to a common output as determined by a 4-bit binary address. The DG407 selects one of eight differential inputs to a common differential output. Break-before-make switching action protects against momentary shorting of inputs. • • • • • • • An on channel conducts current equally well in both directions. In the off state each channel blocks voltages up to the power supply rails. An enable (EN) function allows the user to reset the multiplexer/demultiplexer to all switches off for stacking several devices. All control inputs, address (Ax) and enable (EN) are TTL compatible over the full specified operating temperature range. Applications for the DG406, DG407 include high speed data acquisition, audio signal switching and routing, ATE systems, and avionics. High performance and low power dissipation make them ideal for battery operated and remote instrumentation applications. Designed in the 44 V silicon-gate CMOS process, the absolute maximum voltage rating is extended to 44 V, allowing operation with ± 20 V supplies. Additionally single (12 V) supply operation is allowed. An epitaxial layer prevents latchup. For applications information please request documents 70601 and 70604. Low on-resistance - RDS(on): 50  Low charge injection - Q: 15 pC Available Fast transition time - tTRANS: 200 ns Low power: 0.2 mW Available Single supply capability 44 V supply max. rating Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 Note * This datasheet provides information about parts that are RoHS-compliant and / or parts that are non RoHS-compliant. For example, parts with lead (Pb) terminations are not RoHS-compliant. Please see the information / tables in this datasheet for details BENEFITS • • • • • • Higher accuracy Reduced glitching Improved data throughput Reduced power consumption Increased ruggedness Wide supply ranges: ± 5 V to ± 20 V APPLICATIONS • • • • • • • Data acquisition systems Audio signal routing Medical instrumentation ATE systems Battery powered systems High-rel systems Single supply systems FUNCTIONAL BLOCK DIAGRAM AND PIN CONFIGURATION DG406 DG407 Dual-In-Line and SOIC Wide-Body Dual-In-Line and SOIC Wide-Body V+ 1 28 Da V- Db 2 27 V- NC 3 26 S8a V+ 1 28 D NC 2 27 NC 3 26 S8 S16 4 25 S7 S8b 4 25 S7a 24 S6 S7b 5 24 S6a 6 23 S5a S15 5 S14 6 23 S5 S6b S13 7 22 S4 S5b 7 22 S4a S12 8 21 S3 S4b 8 21 S3a S3b 9 20 S2a S11 9 20 S2 S10 10 19 S1 S2b 10 19 S1a 18 EN S1b 11 18 EN 17 A0 GND 12 NC NC S9 11 GND 12 Decoders/Drivers NC 13 16 A1 A3 14 15 A2 Top View E24-0223-Rev. L, 29-Apr-2024 2 17 A0 13 16 A1 14 15 A2 Decoders/Drivers Top View Document Number: 70061 1 For technical questions, contact: analogswitchsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DG406, DG407 www.vishay.com Vishay Siliconix FUNCTIONAL BLOCK DIAGRAM AND PIN CONFIGURATION 5 25 S7 S7b S14 6 24 S6 S13 7 23 S5 Da V- S15 V+ D 28 27 26 Db V+ 1 NC NC 2 S 8b NC 3 S8 S 16 4 S 8a PLCC and LCC DG407 4 3 2 1 28 27 26 V- PLCC and LCC DG406 5 25 S7a S6b 6 24 S6a S5b 7 23 S5a S4b 8 22 S4a S12 8 22 S4 S11 9 21 S3 S3b 9 21 S3a S10 10 20 S2 S2b 10 20 S2a S9 11 19 S1 S1b 11 19 S1a Top View EN A0 A1 A2 NC NC GND EN A0 NC A1 12 13 14 15 16 17 18 A2 12 13 14 15 16 17 18 A3 Decoders/Drivers GND Decoders/Drivers Top View TRUTH TABLE (DG406) TRUTH TABLE (DG407) A3 A2 A1 A0 EN ON SWITCH A2 A1 A0 EN ON SWITCH PAIR X 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 X 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 X 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 X 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 None 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 X 0 0 0 0 1 1 1 1 X 0 0 1 1 0 0 1 1 X 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 None 1 2 3 4 5 6 7 8 ORDERING INFORMATION (DG406) TEMP. RANGE -40 °C to +85 °C PACKAGE PART NUMBER 28-pin PLCC DG406DN-T1-E3 28-pin widebody SOIC DG406DW-E3, DG406DW-T1-E3 Notes • Logic “0” = VAL  0.8 V • Logic “1” = VAH 2.4 V • X = do not care ORDERING INFORMATION (DG407) TEMP. RANGE -40 °C to +85 °C PACKAGE PART NUMBER 28-pin PLCC DG407DN-T1-E3 28-pin widebody SOIC DG407DW-E3, DG407DW-T1-E3 Note • -T1 indicates tape and reel, -E3 indicates lead (Pb)-free and RoHS-compliant E24-0223-Rev. L, 29-Apr-2024 Document Number: 70061 2 For technical questions, contact: analogswitchsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DG406, DG407 www.vishay.com Vishay Siliconix ABSOLUTE MAXIMUM RATINGS PARAMETER Voltages referenced to V- LIMIT V+ to V - f 44 GND to V- -25 (V-) - 2 to (V+) + 2 V or 20 mA, whichever occurs first 30 Digital inputs a, VS, VD Current (any terminal) Peak current, S or D (pulsed at 1 ms, 10 % duty cycle max.) Storage temperature Power dissipation (package)b 100 (AK, AZ suffix) -65 to +150 (DJ, DN suffix) -65 to +125 28-pin plastic DIP b 625 28-pin plastic PLCC c 450 28-pin widebody SOIC 450 UNIT V mA °C mW Notes a. Signals on SX, DX or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings b. All leads soldered or welded to PC board c. Derate 6 mW/°C above 75 °C d. Derate 12 mW/°C above 75 °C e. Derate 13.5 mW/°C above 75 °C f. Also applies when V- = GND E24-0223-Rev. L, 29-Apr-2024 Document Number: 70061 3 For technical questions, contact: analogswitchsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DG406, DG407 www.vishay.com Vishay Siliconix SPECIFICATIONS a PARAMETER SYMBOL TEST CONDITIONS UNLESS OTHERWISE SPECIFIED V+ = 15 V, V- = -15 V VAL = 0.8 V, VAH = 2.4 V f D SUFFIX -40 °C TO +85 °C TEMP. b TYP. c UNIT MIN. d MAX. d Analog Switch Analog signal range e Drain-source on-resistance RDS(on) matching between channels g Source off leakage current Drain off leakage current VANALOG RDS(on) VD = ± 10 V, IS = -10 mA sequence each switch on RDS(on) VD = ± 10 V IS(off) ID(off) VEN = 0 V, VD = ± 10 V, VS = ± 10 V DG406 DG407 Drain on leakage current ID(on) VS = VD = ± 10 sequence each switch on DG406 DG407 Full - -15 15 V Room 50 - 100 Full 50 - 125  Room 5 - - Room 0.01 -0.5 0.5 5 Full 0.01 -5 Room 0.04 -1 1 Full 0.04 -40 40 Room 0.04 -1 1 Full 0.04 -20 20 Room 0.04 -1 1 Full 0.04 -40 40 Room 0.04 -1 1 Full 0.04 -20 20 % nA Digital Control Logic high input voltage VINH Full - 2.4 - Logic low input voltage VINL Full - - 0.8 Logic high input current IAH VA = 2.4 V, 15 V Full - -1 1 Logic low input current IAL VEN = 0 V, 2.4 V, VA = 0 V Full - -1 1 Logic input capacitance Cin f = 1 MHz Room 7 - - Transition time tTRANS see figure 2 Room 200 - 350 Full - - 450 Break-before-make interval tOPEN see figure 4 Room 50 25 - Full - 10 - Enable turn-on time tON(EN) Room 150 - 200 400 V μA pF Dynamic Characteristics Full - - Room 70 - 150 Full - - 300 Room 15 - - pC Room -69 - - dB Room 8 - - Room 130 - - DG407 Room 65 - - DG406 Room 140 - - DG407 Room 70 - - Room 13 - 30 Full - - 75 Room -0.01 -1 - Full - -10 - Room 50 - 500 - 700 Room -0.01 -20 - Full -0.01 -20 - see figure 3 Enable turn-off time tOFF(EN) Charge injection Q isolation h OIRR Off Source off capacitance Drain off capacitance Drain on capacitance CS(off) CD(off) CD(on) VS = 0 V, CL = 1 nF, RS = 0  VEN = 0 V, RL = 1 k, f = 100 kHz VEN = 0 V, VS = 0 V, f = 1 MHz VEN = 0 V, VD = 0 V, f = 1 MHz ns pF Power Supplies Positive supply current I+ VEN = VA = 0 or 5 V Negative supply current Positive supply current II+ VEN = 2.4 V, VA = 0 V Negative supply current E24-0223-Rev. L, 29-Apr-2024 I- Full μA Document Number: 70061 4 For technical questions, contact: analogswitchsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DG406, DG407 www.vishay.com Vishay Siliconix SPECIFICATIONS a (for single supply) PARAMETER SYMBOL TEST CONDITIONS UNLESS OTHERWISE SPECIFIED V+ = 12 V, V- = 0 V VAL = 0.8 V, VAH = 2.4 V f D SUFFIX -40 °C TO +85 °C TEMP. b TYP. c UNIT MIN. d MAX. d Analog Switch Analog signal range e Drain-source on-resistance RDS(on) matching between channels g Source off leakage current Drain off leakage current Drain on leakage current VANALOG Full - 0 12 V RDS(on) Room 90 - 120  Room 5 - - % RDS(on) IS(off) ID(off) ID(on) VD = 3 V, 10 V, IS = -1 mA sequence each switch on VEN = 0 V, VD = 10 V or 0.5 V, VS = 0.5 V or 10 V VS = VD = ± 10 V sequence each switch on Room 0.01 - - DG406 Room 0.04 - - DG407 Room 0.04 - - DG406 Room 0.04 - - DG407 Room 0.04 - - nA Dynamic Characteristics Switching time of Multiplexer tOPEN VS1 = 8 V, VS8 = 0 V, VIN = 2.4 V Room 300 - 450 Enable turn-on time tON(EN) Room 250 - 600 Enable turn-off Time tOFF(EN) VINH = 2.4 V, VINL = 0 V, VS1 = 5 V Room 150 - 300 Q CL = 1 nF, VS = 6 V, RS = 0  Room 20 - - Room 13 - 30 Full - - 75 Room -0.01 -20 - Full -0.01 -20 - Charge injection ns pC Power Supplies Positive supply current I+ Negative supply current I- VEN = 0 V or 5 V, VA = 0 V or 5 V μA Notes a. Refer to PROCESS OPTION FLOWCHART b. Room = 25 °C, full = as determined by the operating temperature suffix c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this datasheet e. Guaranteed by design, not subject to production test f. VIN = input voltage to perform proper function g. RDS(on) = RDS(on) max. - RDS(on) min. h. Worst case isolation occurs on Channel 4 due to proximity to the drain pin Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. E24-0223-Rev. L, 29-Apr-2024 Document Number: 70061 5 For technical questions, contact: analogswitchsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DG406, DG407 www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (TA = 25 °C, unless otherwise noted) 160 80 RDS(on) - On-Resistance (Ω) RDS(on) - On-Resistance (Ω) 70 120 ± 5V 80 ±8V ± 10 V ± 12 V ± 15 V 40 125 °C 60 85 °C 50 25 °C 40 0 °C 30 - 40 °C 20 - 55 °C ± 20 V 10 0 - 20 - 12 -4 4 VD - Drain Voltage (V) 12 V+ = 15 V V- = - 15 V 0 - 15 20 - 10 -5 0 5 10 15 10 15 VD - Drain Voltage (V) RDS(on) vs. VD and Supply RDS(on) vs. VD and Temperature 120 V- = 0 V 240 V+ = 15 V V- = - 15 V VS = - VD for ID(off) VD = V S(open) for ID(on) 80 200 I D , I S - Current (pA) RDS(on) - On-Resistance (Ω) V+ = 7.5 V 160 10 V 120 12 V 15 V 80 20 V 40 IS(off) 0 DG406 ID(on), ID(off) - 40 22 V DG407 ID(on), ID(off) - 80 40 0 0 4 8 12 16 - 120 - 15 20 VD - Drain Voltage (V) 0 5 ID, IS Leakage Currents vs. Analog Voltage 350 100 nA V+ = 15 V V- = - 15 V VD = "14 V 300 tTRANS 250 1 nA ID(on), ID(off) Time (ns) I D , I S - Current -5 VS , V D - Source Drain Voltage (V) RDS(on) vs. VD and Supply 10 nA - 10 100 pA 200 tON(EN) 150 IS(off) 10 pA 100 tOFF(EN) 1 pA 50 0.1 pA - 55 - 35 - 15 0 5 25 45 65 85 Temperature (°C) ID, IS Leakages vs. Temperature E24-0223-Rev. L, 29-Apr-2024 105 125 ±5 ± 10 ± 15 ± 20 VSUPPLY - Supply Voltage (V) Switching Times vs. Bipolar Supplies Document Number: 70061 6 For technical questions, contact: analogswitchsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DG406, DG407 www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (TA = 25 °C, unless otherwise noted) 70 700 600 60 500 50 tTRANS 400 Q (pC) Time (ns) V- = 0 V 300 40 V+ = 12 V, V- = 0 V 30 tON(EN) 200 V+ = 15 V, V- = - 15 V 20 100 10 tOFF(EN) 0 5 10 15 0 - 15 20 - 10 -5 0 5 Switching Times vs. Single Supply 15 Charge Injection vs. Analog Voltage - 140 10 EN = 5 V AX = 0 or 5 V 8 - 120 I+ 6 - 100 4 I - Current (mA) ISOL (dB) 10 VS - Source Voltage (V) V+ - Supply Voltage (V) - 80 - 60 2 0 -2 IGND -4 - 40 I-6 - 20 -8 0 - 10 100 1K 10K 100K 1M 10 10M 100 1K 1M 10M Supply Currents vs. Switching Frequency 300 3 V+ = 15 V V- = - 15 V 2 220 tTRANS V TH (V) Time (ns) 100K f - Frequency (Hz) f - Frequency (Hz) Off-Isolation vs. Frequency 260 10K tON(EN) 180 1 140 100 tOFF(EN) 0 60 - 55 - 35 - 15 5 25 45 65 Temperature (°C) tON/tOFF vs. Temperature E24-0223-Rev. L, 29-Apr-2024 85 105 125 0 5 10 15 20 VSUPPLY - Supply Voltage (V) Switching Threshold vs. Supply Voltage Document Number: 70061 7 For technical questions, contact: analogswitchsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DG406, DG407 www.vishay.com Vishay Siliconix SCHEMATIC DIAGRAM (typical channel) V+ VREF GND D A0 V+ Level Shift AX V- Decode/ Drive S1 V+ EN Sn V- Fig. 1 TEST CIRCUITS + 15 V + 2.4 V V+ EN A2 A1 ± 10 V S1 A3 S2 - S 15 DG406 S16 A0 ± 10 V VO D GND Logic Input V- tr < 20 ns tf < 20 ns 3V 50 % 0V 50 Ω 35 pF 300 Ω - 15 V VS1 90 % Switch Output + 15 V + 2.4 V V+ EN A2 VO S1b 0V 90 % ± 10 V VS8 * DG407 S8b A1 A0 S1 ON Db GND tTRANS tTRANS ± 10 V S8 ON VO V- 50 Ω 300 Ω 35 pF - 15 V * = S1a - S 8a, S2b S ± 7b, Da Fig. 2 - Transition Time E24-0223-Rev. L, 29-Apr-2024 Document Number: 70061 8 For technical questions, contact: analogswitchsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DG406, DG407 www.vishay.com Vishay Siliconix TEST CIRCUITS + 15 V V+ A3 -5V S1 A2 S2 - S 16 A1 DG406 A0 VO D EN GND V35 pF 300 Ω 50 Ω Logic Input - 15 V tr < 20 ns tf < 20 ns 3V 50 % 0V tON(EN) 0V + 15 V V+ A2 S1b S1a - S 8a S2b - S 8b A1 A0 tOFF(EN) Switch Output -5V VO 90 % 90 % VO DG407 Da and Db EN GND VO V- 35 pF 50 Ω 300 Ω - 15 V Fig. 3 - Enable Switching Time + 15 V Logic Input V+ EN + 2.4 V All S and Da A3 A2 A1 +5V tr < 20 ns tf < 20 ns 3V 50 % 0V DG406 DG407 A0 GND 50 Ω VS VO D,D b 80 % Switch Output V300 Ω 35 pF VO - 15 V 0V tOPEN Fig. 4 - Break-Before-Make Interval E24-0223-Rev. L, 29-Apr-2024 Document Number: 70061 9 For technical questions, contact: analogswitchsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DG406, DG407 www.vishay.com Vishay Siliconix APPLICATIONS HINTS Sampling speed is limited by two consecutive events: the transition time of the multiplexer, and the settling time of the sampled signal at the output. tTRANS is given on the data sheet. Settling time at the load depends on several parameters: RDS(on) of the multiplexer, source impedance, multiplexer and load capacitances, charge injection of the multiplexer and accuracy desired. The settling time for the multiplexer alone can be derived from the model shown in figure 5. Assuming a low impedance signal source like that presented by an op amp or a buffer amplifier, the settling time of the RC network for a given accuracy is equal to n: % ACCURACY # BITS N 0.25 8 6 0.012 12 9 0.0017 15 11 VOUT CD(on) Fig. 5 - Simplified Model of One Multiplexer Channel The maximum sampling frequency of the multiplexer is: 1 f s = ------------------------------------------------------------- (1) N  t SETTLING + t TRANS  to From the sampling theorem, to properly recover the original signal, the sampling frequency should be more than twice the maximum component frequency of the original signal. This assumes perfect bandlimiting. In a real application sampling at three to four times the filter cutoff frequency is a good practice. (4) The block diagram shown in figure 6 illustrates a typical data acquisition front end suitable for low-level analog signals. Differential multiplexing of small signals is preferred since this method helps to reject any common mode noise. This is especially important when the sensors are located at a distance and it may eliminate the need for individual amplifiers. A low RDS(on), low leakage multiplexer like the DG407 helps to reduce measurement errors. The low power dissipation of the DG407 minimizes on-chip thermal gradients which can cause errors due to temperature mismatch along the parasitic thermocouple paths. Please refer to Application Note AN203 for additional information. scan To Sensor 1 To Sensor 8 (3) From this we can see that the DG406 can be used to sample 16 different signals whose maximum component frequency can be as high as 173 kHz. If for example, two channels are used to double sample the same incoming signal then its cutoff frequency can be doubled. RS = 0 channels f s = 694 kHz Therefore from equation 2 above: 1 f c = ---  f s = 173 kHz 4 R DS(on) where N = number of tSETTLING = n = n x RDS(on) x CD(on) For the DG406 then, at room temp and for 12-bit accuracy, using the maximum limits: 1 (2) f s = -------------------------------------------------------------------------------------------------------- 12 - 12 16  9  100   10 F  + 300  10 s or Analog Multiplexer Inst Amp DG407 S/H 12-Bit A/D Converter Controller Fig. 6 - Measuring Low-Level Analog Signals is more accurate when using a Differential Multiplexing Technique E24-0223-Rev. L, 29-Apr-2024 Document Number: 70061 10 For technical questions, contact: analogswitchsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DG406, DG407 www.vishay.com Vishay Siliconix PRODUCT SUMMARY Part number DG406 DG406 DG407 Status code 2 2 2 2 16:1 x 1 16:1 x 1 8:1 x 2 8:1 x 2 Configuration DG407 Single supply min. (V) 5 5 5 5 Single supply max. (V) 44 44 44 44 Dual supply min. (V) 5 5 5 5 Dual supply max. (V) 22 22 22 22 On-resistance () 50 50 50 50 Charge injection (pC) 15 15 15 15 Source on capacitance (pF) 140 140 70 70 Source off capacitance (pF) 8 8 8 8 Leakage switch on typ. (nA) 0.04 0.04 0.04 0.04 Leakage switch off max. (nA) 0.5 0.5 0.5 0.5 - - - - SO-28 (wide) PLCC-28 SO-28 (wide) PLCC-28 -3 dB bandwidth (MHz) Package Functional circuit / applications Interface Multi purpose, Multi purpose, Multi purpose, Multi purpose, instrumentation, medical instrumentation, medical instrumentation, medical instrumentation, medical and healthcare and healthcare and healthcare and healthcare Parallel Parallel Parallel Parallel Single supply operation Yes Yes Yes Yes Dual supply operation Yes Yes Yes Yes Turn on time max. (ns) 350 350 350 350 Crosstalk and off isolation -69 -69 -69 -69 Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?70061. E24-0223-Rev. L, 29-Apr-2024 Document Number: 70061 11 For technical questions, contact: analogswitchsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Package Information Vishay Siliconix PDIP: 28ĆLEAD 28 27 26 25 24 23 22 21 20 19 18 17 16 15 E1 1 2 3 4 5 6 7 8 9 10 11 12 13 E 14 D Q1 S A(1) A L A1 L 15° MAX. C e1 B1 Dim A A1 B B1 C D E E1 e1 eA L Q1 S eA B MILLIMETERS Min Max INCHES Min Max 2.29 5.08 0.090 0.200 0.39 1.77 0.015 0.070 0.38 0.56 0.015 0.022 0.89 1.65 0.035 0.065 0.204 0.30 0.008 0.012 35.10 39.70 1.380 1.565 15.24 15.88 0.600 0.625 13.21 14.73 0.520 0.580 2.29 2.79 0.090 0.110 14.99 15.49 0.590 0.610 2.60 5.08 0.100 0.200 0.95 2.345 0.0375 0.0925 0.995 2.665 0.0375 0.105 ECN: S-03946—Rev. F, 09-Jul-01 DWG: 5488 Document Number: 71243 06-Jul-01 www.vishay.com 1 Package Information Vishay Siliconix PLCC: 28-LEAD D-SQUARE MILLIMETERS MIN. MAX. A 4.20 4.57 2.29 3.04 A1 0.51 A2 B 0.331 0.553 0.661 0.812 B1 D 12.32 12.57 11.430 11.582 D1 9.91 10.92 D2 1.27 BSC e1 ECN: T09-0766-Rev. D, 28-Sep-09 DWG: 5491 DIM. A2 INCHES MIN. MAX. 0.165 0.180 0.090 0.120 0.020 0.013 0.021 0.026 0.032 0.485 0.495 0.450 0.456 0.390 0.430 0.050 BSC e1 B1 D2 B D1-SQUARE A1 D A Document Number: 71264 28-Sep-09 0.101 mm 0.004" www.vishay.com 1 Package Information www.vishay.com Vishay Siliconix SOIC (WIDE-BODY): 28-LEADS 0.06 0.002D CAVITY NO. 0.3525 0.001 0.334 0.005 28 27 26 25 24 23 22 21 20 19 18 R0.004 17 16 15 0.010 0.1475 0.001 R0.008 0.295 0.001 R0.009 1 2 3 4 5 6 7 8 9 10 11 12 13 14 4° R0.004 2° 0.032 0.005 0.070 0.005 0.055 0.005 DETAIL A PIN 1 INDICATOR 0.047 0.007 0.001 dp SURFACE POLISHED 0.334 0.005 0.291 0.001 0.091 0.001 0.020 45° 0.705 0.001 0.098 0.002 R0.004 0.00825 ± 0.00325 0.041 0.001 0.050 TYP. 0.017 0.0003 7°(4 ) 0.295 0.001 0.406 0.004 DETAIL A All Dimensions In Inches ECN: E11-2209-Rev. D, 01-Aug-11 DWG: 5850 Revision: 01-Aug-11 1 Document Number: 71268 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2024 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Document Number: 91000 1 For technical questions, contact: THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 01-Jan-2024