F340X152248KPI2T0

F340X1 480VAC www.vishay.com Vishay BCcomponents THB Grade IIIB Class X1 Interference Suppression Film Capacitor Radial MKP 480 VAC - Three Phase Across the Line FEATURES • IEC 60384-14: 2013 / AMD1: 2016 grade IIIB: 85 °C, 85 % RH, 1000 h at URAC certified • AEC-Q200 qualified • Maximum permissible AC voltage up to 530 V • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS LINKS TO ADDITIONAL RESOURCES For standard across the line X1 and series impedance applications. See also application note: www.vishay.com/doc?28153 3D 3D 3D Models QUICK REFERENCE DATA Rated capacitance range Capacitance tolerance Rated voltage range, URAC Permissible DC voltage Climatic testing class Maximum application temperature Reference standards Dielectric Electrodes 220 nF to 8.2 μF (preferred values according to E12) ± 20 %; ± 10 % 480 VAC 800 VDC at 105 °C 1000 VDC at 85 °C 40 / 105 / 56 / B 105 °C IEC 60384-14:2013 IEC 60384-14:2013 / AMD1:2016 EN 60384-14 IEC 60065 requires passive flammability class B UL 60384-14 (2nd edition) CSA-E60384-1:14 (3rd edition) CQC AEC-Q200 qualified (rev. D) up to 105 °C Polypropylene film Metallized Series construction Construction Encapsulation Leads Marking Plastic case, epoxy resin sealed, flame retardant UL-class 94 V-0 Tinned wire C-value; tolerance; rated voltage; sub-class; manufacturer’s type; code for dielectric material; manufacturer location, manufacturer’s logo; year and week; safety approvals Note • For more detailed data and test requirements, contact rfi@vishay.com DIMENSIONS in millimeters l w h lt P Revision: 08-Sep-2022 Ø dt Document Number: 26073 1 For technical questions, contact: rfi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 F340X1 480VAC www.vishay.com Vishay BCcomponents COMPOSITION OF CATALOG NUMBER CODE Example: MULTIPLIER 0.1 2 427 270 nF 0.27 μF 1 3 510 1000 nF 1.0 μF 10 4 100 5 P1 (mm) PITCH CODE 27.5 K 37.5 P 52.5 Y SPECIAL CODE FOR TERMINAL VOLTAGE 2 2 pins 48 = 480 VAC (#) Customized 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 F 3 4 0 X 1 4 2 7 4 M K M 2 B 0 8 TOLERANCE CLASS M ± 20 % K ± 10 % SPECIAL 0 = Standard TYPE Other = Special L1 (mm) LEAD LENGTH CODE PITCH (mm) 3.5 ± 0.3 P ≥ 27.5 5±1 M All 25 ± 2 I All PACKING CODE PACKING STYLE REMARK B Bulk Pitch 27.5 mm and lead length 25 mm ± 2 mm T Tray Rest all 0: Space holder Note • Taped on reel not available Revision: 08-Sep-2022 Document Number: 26073 2 For technical questions, contact: rfi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 F340X1 480VAC www.vishay.com Vishay BCcomponents SPECIFIC REFERENCE DATA DESCRIPTION VALUE Rated voltage range, URAC 480 VAC Maximum permissible AC voltage 530 V 800 VDC at 105 °C 1000 VDC at 85 °C Rated voltage range, URDC Tangent of loss angle: At 1 kHz At 10 kHz C ≤ 1.5 μF ≤ 20 x 10-4 ≤ 30 x 10-4 1.5 μF< C ≤ 3.9 μF ≤ 30 x 10-4 ≤ 50 x 10-4 C > 3.9 μF ≤ 40 x 10-4 ≤ 80 x 10-4 Rated voltage pulse slope (du/dt)R at 670 VDC Pitch = 27.5 mm 100 V/μs Pitch = 37.5 mm 80 V/μs Pitch = 52.5 mm 35 V/μs R between leads, for C ≤ 0.33 μF at 100 V; 1 min > 15 000 MΩ RC between leads, for C > 0.33 μF at 100 V; 1 min > 5000 s R between leads and case; 100 V; 1 min > 30 000 MΩ Withstanding (DC) voltage (cut off current 10 mA) (1); rise time ≤ 1000 V/s: C ≤ 1 μF 3400 V; 1 min C > 1 μF 2500 V; 1 min Withstanding (AC) voltage between leads and case 2460 V; 1 min Note (1) See “Voltage Proof Test for Metalized Film Capacitors”: www.vishay.com/doc?28169 ELECTRICAL DATA AND ORDERING INFORMATION CATALOG NUMBER F340X1... AND PACKAGING URAC (V) CAP. (μF) DIMENSIONS (2) wxhxl (mm) LOOSE IN BOX MASS (g) (1) SHORT LEADS lt = 3.5 mm ± 0.3 mm lt = 5.0 mm ± 1.0 mm LONG LEADS SPQ lt = 25.0 mm ± 2.0 mm SPQ PITCH = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 20 % 0.22 42248MKM2T0 43348MKP2T0 43348MKM2T0 12.3 44748MKP2T0 44748MKM2T0 95 44748MKI2B0 95 16.1 46848MKP2T0 46848MKM2T0 80 46848MKI2B0 80 21.0 x 31.0 x 32.0 20.3 51048MKP2T0 51048MKM2T0 65 51048MKI2B0 65 22.0 x 38.0 x 32.0 42.5 51548MKP2T0 51548MKM2T0 60 51548MKI2B0 65 9.2 0.47 15.0 x 25.0 x 32.0 0.68 18.0 x 28.0 x 32.0 1.0 1.5 0.33 480 42248MKP2T0 13.0 x 23.0 x 32.0 115 42248MKI2B0 43348MKI2B0 115 PITCH = 37.5 mm ± 0.4 mm; dt = 1.00 mm ± 0.1 mm; C-TOL. = ± 20 % 2.2 21.5 x 38.5 x 42.0 61 52248MPP2T0 52248MPM2T0 84 52248MPI2T0 84 3.3 30.0 x 45.0 x 42.0 94.5 53348MPP2T0 53348MPM2T0 63 53348MPI2T0 63 PITCH = 52.5 mm ± 0.4 mm; dt = 1.20 mm ± 0.12 mm; C-TOL. = ± 20 % 4.7 6.8 30.0 x 45.0 x 57.5 138.5 54748MYP2T0 54748MYM2T0 135 56848MYP2T0 56848MYM2T0 45 54748MYI2T0 56848MYI2T0 45 Notes • SPQ = Standard Packing Quantity (1) Weight for short lead product only (2) For tolerances see chapter “Space Requirements for Printed-Circuit Board Applications and Dimension Tolerances” Revision: 08-Sep-2022 Document Number: 26073 3 For technical questions, contact: rfi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 F340X1 480VAC www.vishay.com Vishay BCcomponents ELECTRICAL DATA AND ORDERING INFORMATION CATALOG NUMBER F340X1... AND PACKAGING URAC (V) CAP. (μF) DIMENSIONS (2) wxhxl (mm) LOOSE IN BOX MASS (g) (1) SHORT LEADS lt = 3.5 mm ± 0.3 mm lt = 5.0 mm ± 1.0 mm LONG LEADS SPQ lt = 25.0 mm ± 2.0 mm SPQ PITCH = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 10 % 0.22 0.27 13.0 x 23.0 x 32.0 9.2 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 15.0 x 25.0 x 32.0 12.3 18.0 x 28.0 x 32.0 16.1 21.0 x 31.0 x 32.0 20.3 22.0 x 38.0 x 32.0 480 22.5 42248KKP2T0 42248KKM2T0 42748KKP2T0 42748KKM2T0 43348KKP2T0 43348KKM2T0 43948KKP2T0 43948KKM2T0 44748KKP2T0 44748KKM2T0 45648KKP2T0 45648KKM2T0 46848KKP2T0 46848KKM2T0 48248KKP2T0 48248KKM2T0 51048KKP2T0 51048KKM2T0 51248KKP2T0 51248KKM2T0 42248KKI2B0 115 42748KKI2B0 115 43348KKI2B0 43948KKI2B0 95 44748KKI2B0 45648KKI2B0 80 46848KKI2B0 48248KKI2B0 65 51048KKI2B0 60 51248KKI2B0 95 80 65 65 PITCH = 37.5 mm ± 0.4 mm; dt = 1.00 mm ± 0.1 mm; C-TOL. = ± 10 % 1.5 1.8 21.5 x 38.5 x 42.0 2.2 2.7 3.3 30.0 x 45.0 x 42.0 3.9 61.5 51548KPP2T0 51548KPM2T0 61 51848KPP2T0 51848KPM2T0 60 52248KPP2T0 52248KPM2T0 95.5 52748KPP2T0 52748KPM2T0 92.5 53348KPP2T0 53348KPM2T0 88.5 53948KPP2T0 53948KPM2T0 51548KPI2T0 84 51848KPI2T0 84 52248KPI2T0 52748KPI2T0 63 53348KPI2T0 63 53948KPI2T0 PITCH = 52.5 mm ± 0.4 mm; dt = 1.20 mm ± 0.12 mm; C-TOL. = ± 10 % 4.7 5.6 6.8 8.2 30.0 x 45.0 x 57.5 35.0 x 50.0 x 57.5 137.5 54748KYP2T0 54748KYM2T0 136 55648KYP2T0 55648KYM2T0 171 56848KYP2T0 56848KYM2T0 165.5 58248KYP2T0 58248KYM2T0 45 40 54748KYI2T0 55648KYI2T0 56848KYI2T0 58248KYI2T0 45 40 Notes • SPQ = Standard Packing Quantity (1) Weight for short lead product only (2) For tolerances see chapter “Space Requirements for Printed-Circuit Board Applications and Dimension Tolerances” APPROVALS SAFETY APPROVALS X1 VOLTAGE VALUE FILE NUMBERS LINK EN 60384-14 (ENEC) (= IEC 60384-14 ed-4 (2013)) 480 VAC 220 nF to 8.2 μF ENEC/FI/19/10008/A1 www.vishay.com/doc?28247 UL 60384-14 480 VAC 220 nF to 8.2 μF E354331 www.vishay.com/doc?28249 CSA-E384-14 480 VAC 220 nF to 8.2 μF E354331 www.vishay.com/doc?28249 L-18001205119 www.vishay.com/doc?28248 CQC 480 VAC 220 nF to 8.2 μF CB-test certificate 480 VAC 220 nF to 8.2 μF F-18001207457 www.vishay.com/doc?28250 FI-39834 www.vishay.com/doc?28246 The ENEC-approval together with the CB-certificate replace all national marks of the following countries (they have already signed the ENEC-agreement): Austria; Belgium; Czech Republic; Denmark; Finland; France; Germany; Greece; Hungary; Ireland; Italy; Luxembourg; Netherlands; Norway; Portugal; Slovenian; Spain; Sweden, Switzerland, and United Kingdom. Revision: 08-Sep-2022 Document Number: 26073 4 For technical questions, contact: rfi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 F340X1 480VAC www.vishay.com Vishay BCcomponents MOUNTING Normal Use The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for mounting in printed-circuit boards by means of automatic insertion machines. Specific Method of Mounting to Withstand Vibration and Shock In order to withstand vibration and shock tests, it must be ensured that the stand-off pips are in good contact with the printed-circuit board. • For pitches ≥ 27.5 mm the capacitors shall be mechanically fixed by the leads and the body clamped Space Requirements for Printed-Circuit Board Applications and Dimension Tolerances For the maximum product dimensions and maximum space requirements for length (lmax.), width (wmax.), and height (hmax.) following tolerances must be taken in account in the envelopment of the components as shown in the drawings below. Imax. = l + Δl, wmax. = w + Δw, and hmax. = h + Δh • For products with pitch = 27.5 mm, Δw = Δl = Δh = 0.7 mm • For products with pitch = 37.5 mm, Δw = Δl = Δh = 0.7 mm • For products with pitch = 52.5 mm, Δw = Δl = Δh = 1.0 mm Eccentricity defined as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product concerned. wmax. = w + Δw Eccentricity Imax. = I + ΔI CBA116 hmax. = h + Δh Seating plane For the minimum product dimensions for length (lmin.), width (wmin.), and height (hmin.) following tolerances of the components are valid: lmin. = l - Δl, wmin. = w - Δw, and hmin. = h - Δh • For products with pitch = 27.5 mm, Δw = Δl = Δh = 1.0 mm • For products with pitch = 37.5 mm, Δw = Δl = Δh = 1.0 mm • For products with pitch = 52.5 mm, Δw = Δl = Δh = 1.5 mm SOLDERING CONDITIONS For general soldering conditions and wave soldering profile we refer to the document “Soldering Guidelines for Film Capacitors”: www.vishay.com/doc?28171 STORAGE TEMPERATURE Tstg = -25 °C to +35 °C with RH maximum 75 % without condensation. RATINGS AND CHARACTERISTICS REFERENCE CONDITIONS Unless otherwise specified. all electrical values apply to an ambient temperature of 23 °C ± 1°C, an atmospheric pressure of 86 kPa to 106 kPa and a relative humidity of 50 % ± 2 %. For reference testing. a conditioning period shall be applied over 96 hours ± 4 hours by heating the products in a circulating air oven at the rated temperature and a relative humidity not exceeding 20 %. Revision: 08-Sep-2022 Document Number: 26073 5 For technical questions, contact: rfi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 F340X1 480VAC www.vishay.com Vishay BCcomponents CHARACTERISTICS Axis Title Axis Title 10000 100 Typical 0 Maximum -2 100 -4 2nd line Impedance (I) 220 nF 1000 Minimum 10 -50 0 50 1 2200 nF 0.1 100 4700 nF 8200 nF 0.001 100 10 100 1000 10 000 10 100 000 Ambient Temperature (°C) Frequency (kHz) Capacitance as a function of ambient temperature (typical curve) Impedance as a function of frequency (typical curve) Axis Title Axis Title 10000 10 000 100 10000 10 1000 1000 1.5 μF < C ≤ 3.9 μF 10 100 1st line 2nd line C > 4.7 μF 100 2nd line Frequency (MHz) 1000 1st line 2nd line 2nd line Dissipation Factor (x 10-4) 1000 1000 nF 0.01 -6 470 nF 10 1st line 2nd line 2 10000 1000 1st line 2nd line 2nd line Change in Capacitance (%) 4 220 nF 1 100 X1 0.22 μF < C ≤ 1.5 μF 1 8.2 μF 0.1 0.01 10 0.1 1 10 0.1 100 100 1000 10 000 Frequency (kHz) Capacitance (nF) Tangent of loss angle as a function of frequency (typical curve) Resonant frequency as a function of capacitance (typical curve) Axis Title Axis Title 1000 10000 10000 100 000 4700 nF 100 1000 1000 1st line 2nd line 100 2nd line AC Current (mA) 1st line 2nd line 1000 2200 nF 8200 nF 10 000 2nd line AC Voltage (V) 10 100 000 220 nF 470 nF 100 1000 nF 100 10 Tamb ≤ 110 °C 10 0.01 10 0.1 1 10 100 1 1 10 100 10 1000 Frequency (kHz) Frequency (kHz) Max. RMS voltage as a function of frequency Max. RMS current as a function of frequency Revision: 08-Sep-2022 Document Number: 26073 6 For technical questions, contact: rfi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 F340X1 480VAC www.vishay.com Vishay BCcomponents Axis Title 10000 1000 1st line 2nd line Time Constant 2nd line MΩ x μF (s) 1 000 000 100 000 100 10 10 000 0 20 40 60 80 100 Ambient Temperature (°C) Insulation resistance as a function of ambient temperature (typical curve) APPLICATION NOTES • For X1 electromagnetic interference suppression in standard across the line applications (50 Hz / 60 Hz) with a maximum of 480 VAC rated voltage including fluctuation of the mains. It is recommended to use these components in a mains with maximum nominal voltage of 400 VAC. Higher continuous applied voltages will shorten the life time • For series impedance applications we refer to application note www.vishay.com/doc?28153 • To ensure withstanding high humidity requirements in the application the epoxy adhesion at the leads shall not be damaged. Therefore the leads may not be damaged or not be bent before soldering • For capacitors connected in parallel, normally the proof voltage must be reduced in function of the total parallel capacitance value, see graph. Axis Title 10000 3500 3000 1000 2500 1st line 2nd line 2nd line Maximum Allowed Proof Voltage (V) 4000 2000 1500 100 1000 500 10 0 0 2 4 6 8 10 12 14 16 18 20 Total Parallel Capacitance (μF) Proof voltage as function of total parallel capacitance • These capacitors are not intended for continuous pulse applications. For these situations, capacitors of the AC and pulse programs must be used • The maximum ambient temperature must not exceed 105 °C • Rated voltage pulse slope: if the pulse voltage is lower than the rated voltage, the values of the specific reference data can be multiplied by 670 VDC and divided by the applied voltage Revision: 08-Sep-2022 Document Number: 26073 7 For technical questions, contact: rfi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 F340X1 480VAC www.vishay.com Vishay BCcomponents INSPECTION REQUIREMENTS General Notes Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-14 ed-4 (2013) and Specific Reference Data”. GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1A PART OF SAMPLE OF SUB-GROUP C1 4.1 Dimensions (detail) As specified in chapters “General Data” of this specification Initial measurements Capacitance Tangent of loss angle: for C ≤ 1 μF at 10 kHz for C > 1 μF at 1 kHz 4.3 Robustness of terminations Tensile: load 10 N; 10 s Bending: load 5 N; 4 x 90° 4.4 Resistance to soldering heat No pre-drying Method: 1A Solder bath: 280 °C ± 5 °C Duration: 10 s No visible damage 4.19 Component solvent resistance Isopropylalcohol at room temperature Method: 2 Immersion time: 5 min ± 0.5 min Recovery time: min. 1 h, max. 2 h 4.4.2 Final measurements Visual examination No visible damage Legible marking Capacitance |ΔC/C| ≤ 5 % of the value measured initially Tangent of loss angle Increase of tan δ: ≤ 0.008 for: C ≤ 1 μF ≤ 0.005 for: C > 1 μF Compared to values measured initially Insulation resistance As specified in section “Insulation Resistance” of this specification SUB-GROUP C1B OTHER PART OF SAMPLE OF SUB-GROUP C1 Initial measurements Capacitance Tangent of loss angle: for C ≤ 1 μF at 10 kHz for C > 1 μF at 1 kHz 4.20 Solvent resistance of the marking Isopropyl alcohol at room temperature Method: 1 Rubbing material: cotton wool Immersion time: 5 min ± 0.5 min 4.6 θA = -40 °C θB = +105 °C 5 cycles Duration t = 30 min Rapid change of temperature 4.6.1 Inspection Visual examination 4.7 Mounting: see section “Mounting” of this specification Procedure B4: Frequency range: 10 Hz to 55 Hz Amplitude: 0.75 mm or Acceleration 98 m/s2 (whichever is less severe) Total duration 6 h Vibration Revision: 08-Sep-2022 No visible damage Legible marking No visible damage Document Number: 26073 8 For technical questions, contact: rfi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 F340X1 480VAC www.vishay.com Vishay BCcomponents GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1B OTHER PART OF SAMPLE OF SUB-GROUP C1 4.7.2 Final inspection Visual examination 4.9 Mounting: see section “Mounting” for more information Pulse shape: half sine Acceleration: 490 m/s2 Duration of pulse: 11 ms Shock 4.9.2 Final measurements No visible damage Visual examination No visible damage Capacitance |ΔC/C| ≤ 5 % of the value measured initially Tangent of loss angle Increase of tan δ: ≤ 0.008 for: C ≤ 1 μF ≤ 0.005 for: C > 1 μF Compared to values measured initially Insulation resistance As specified in section “Insulation Resistance” of this specification SUB-GROUP C1 COMBINED SAMPLE OF SPECIMENS OF SUB-GROUPS C1A AND C1B 4.11 Climatic sequence 4.11.1 Initial measurements Capacitance Measured in 4.4.2 and 4.9.2 Tangent of loss angle: measured initially in C1A and C1B 4.11.2 Dry heat Temperature: 105 °C 4.11.3 Damp heat cyclic Test Db First cycle Duration: 16 h 4.11.4 Cold Temperature: -40 °C 4.11.5 Damp heat cyclic Test Db remaining cycles Duration: 2 h 4.11.6 Final measurements Visual examination No visible damage Legible marking Capacitance |ΔC/C| ≤ 5 % of the value measured in 4.11.1. Tangent of loss angle Increase of tan δ: ≤ 0.008 for: C ≤ 1 μF ≤ 0.005 for: C > 1 μF Compared to values measured in 4.11.1. Voltage proof 1900 VDC; 1 min between terminations No permanent breakdown or flash-over Insulation resistance ≥ 50 % of values specified in section “Insulation Resistance” of this specification Revision: 08-Sep-2022 Document Number: 26073 9 For technical questions, contact: rfi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 F340X1 480VAC www.vishay.com Vishay BCcomponents GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C2 4.12 Damp heat steady state 56 days, 40 °C, 90 % to 95 % RH, no load 4.12.1 Initial measurements Capacitance Tangent of loss angle: for C ≤ 1 μF at 10 kHz for C > 1 μF at 1 kHz 4.12.3 Final measurements Visual examination No visible damage Legible marking Capacitance |ΔC/C| ≤ 5 % of the value measured in 4.12.1. Tangent of loss angle Increase of tan δ: ≤ 0.008 for: C ≤ 1 μF ≤ 0.005 for: C > 1 μF Compared to values measured in 4.12.1. Voltage proof 1900 VDC; 1 min between terminations No permanent breakdown or flash-over Insulation resistance ≥ 50 % of values specified in section “Insulation Resistance” of this specification SUB-GROUP C2A 4.12A Damp heat steady state with load 85 °C, 85 % RH, load: 480 VAC Duration: 1000 h 4.12.1A Initial measurements Capacitance Tangent of loss angle: for C ≤ 1 μF at 10 kHz for C > 1 μF at 1 kHz 4.12.3A Final measurements Visual examination No visible damage Legible marking Revision: 08-Sep-2022 Capacitance |ΔC/C| ≤ 10 % of the value measured in 4.12.1A. Tangent of loss angle Increase of tan δ: ≤ 0.0240 for: C ≤ 1 μF at 10 kHz ≤ 0.0150 for: C > 1 μF at 1 kHz Compared to values measured in 4.12.1A. Voltage proof 1900 VDC; 1 min between terminations No permanent breakdown or flash-over Insulation resistance ≥ 50 % of values specified in section “Insulation Resistance” of this specification Document Number: 26073 10 For technical questions, contact: rfi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 F340X1 480VAC www.vishay.com Vishay BCcomponents GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C3 4.13.1 Initial measurements Capacitance Tangent of loss angle: for C ≤ 1 μF at 10 kHz for C > 1 μF at 1 kHz 4.13 Impulse voltage 3 successive impulses, full wave, peak voltage: X1: 4 kV for C ≤ 1 μF 4 kV√C for C > 1 μF Max. 24 pulses 4.14 Endurance Duration: 1000 h 1.25 x URAC at 105 °C Once in every hour the voltage is increased to 1000 VRMS for 0.1 s via resistor of 47 Ω ± 5 % 4.14.7 Final measurements No self healing breakdowns or flash-over Visual examination No visible damage Legible marking Capacitance |ΔC/C| ≤ 10 % compared to values measured in 4.13.1. Tangent of loss angle Increase of tan δ: ≤ 0.008 for: C ≤ 1 μF or ≤ 0.005 for: C > 1 μF Compared to values measured in 4.13.1 Voltage proof 1900 VDC; 1 min between terminations 2380 VAC; 1 min between terminations and case No permanent breakdown or flash-over Insulation resistance ≥ 50 % of values specified in section “Insulation Resistance” of this specification SUB-GROUP C4 4.15 Charge and discharge 10 000 cycles Charged to 670 VDC Discharge resistance: 670 V DC R = -------------------------------------1.5 x C (du/dt) 4.15.1 Initial measurements Capacitance Tangent of loss angle: for C ≤ 1 μF at 10 kHz for C > 1 μF at 1 kHz 4.15.3 Final measurements Capacitance |ΔC/C| ≤ 10 % compared to values measured in 4.15.1. Tangent of loss angle Increase of tan δ: ≤ 0.008 for: C ≤ 1 μF ≤ 0.005 for: C > 1 μF Compared to values measured in 4.15.1 Insulation resistance ≥ 50 % of values specified in section “Insulation Resistance” of this specification Revision: 08-Sep-2022 Document Number: 26073 11 For technical questions, contact: rfi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 F340X1 480VAC www.vishay.com Vishay BCcomponents GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C5 4.16 Radio frequency characteristic Resonance frequency ≥ 0.9 times the value as specified in section “Resonant Frequency” of this specification Bore of gas jet: Ø 0.5 mm Fuel: butane / propane Test duration for actual volume V in mm3: After removing test flame from capacitor, the capacitor must not continue to burn for more than 10 s. No burning particle must drop from the sample. SUB-GROUP C6 4.17 Passive flammability Class B Class B V > 1750 60 s One flame application: 12 mm ~ 8 mm 45.0 ° SUB-GROUP C7 4.18 Active flammability 20 cycles of 4 kV discharges on the test capacitor connected to URAC The cheese cloth around the capacitors shall not burn with a flame. No electrical measurements are required. AUTOMOTIVE AEC-Q200, REVISION D QUALIFICIATION STRESS CONDITIONS 1. High temperature exposure (storage) Test as per MIL-STD 202, method 108 Temperature: 105 °C; unpowered Duration: 1000 h 2. Temperature cycling Test as per JESD22, method JA-104 Total no. of cycles: 1000 cycles Lower temperature: -40 °C Upper temperature: +105 °C 30 min dwell time at each temperature as per rev. D Transition time < 1 min 3. Moisture resistance Test as per MIL-STD 202, method 106 No. of cycle: 10 cycles t = 24 h/cycle 4. Biased humidity AC Test as per MIL-STD 202, method 103 Temperature: 40 °C; RH: 93 %; URAC Duration: 1000 h 5. Operational life AC Test as per MIL-STD 202, method 108 Temperature: 105 °C; URAC Duration: 1000 h Revision: 08-Sep-2022 SAMPLE SIZE PERFORMANCE REQUIREMENTS 77 |ΔC/C| ≤ 10 % Increase of tan δ: ≤ 0.008 for C ≤ 1 μF at 10 kHz ≤ 0.005 for C > 1 μF at 1 kHz IR > 50 % of initial specified value 77 |ΔC/C| ≤ 10 % Increase of tan δ: ≤ 0.008 for C ≤ 1 μF at 10 kHz ≤ 0.005 for C > 1 μF at 1 kHz IR > 50 % of initial specified value 77 |ΔC/C| ≤ 10 % Increase of tan δ: ≤ 0.008 for C ≤ 1 μF at 10 kHz ≤ 0.005 for C > 1 μF at 1 kHz IR > 50 % of initial specified value 77 |ΔC/C| ≤ 10 % Increase of tan δ: ≤ 0.008 for C ≤ 1 μF at 10 kHz ≤ 0.005 for C > 1 μF at 1 kHz IR > 50 % of initial specified value 77 |ΔC/C| ≤ 10 % Increase of tan δ: ≤ 0.008 for C ≤ 1 μF at 10 kHz ≤ 0.005 for C > 1 μF at 1 kHz IR > 50 % of initial specified value Document Number: 26073 12 For technical questions, contact: rfi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 F340X1 480VAC www.vishay.com Vishay BCcomponents AUTOMOTIVE AEC-Q200, REVISION D QUALIFICIATION STRESS CONDITIONS SAMPLE SIZE PERFORMANCE REQUIREMENTS 6. Terminal strength (leaded) Test as per MIL-STD 202, method 211 Test leaded device lead integrity only. A (pull-test): 2.27 kg (10 s) - C (wire-lead bend test): 227 g (3 x 3 s) 30 No visual damage 7. Resistance to solvents MIL-STD-202 method 215 - Also aqueous chemical - OKEM clean or equivalent Do not use banned solvents. 5 No visual damage Legible marking 8. Mechanical shock MIL-STD-202 method 213 100 g's ; 6 ms half-sine; 3.75 m/s 30 No visual damage 9. Vibration MIL-STD-202 method 204 5 g's for 20 min; 12 cycles x 3 directions 10 Hz to 2000 Hz 30 No visual damage 10. Resistance to soldering heat MIL-STD-202 method 210 Temperature: 280 °C; Time: 10 s Procedure 1 solder within 1.5 mm of device body 30 |ΔC/C| ≤ 5 % Increase of tan δ: ≤ 0.008 for C ≤ 1 μF at 10 kHz ≤ 0.005 for C > 1 μF at 1 kHz IR > 50 % of initial specified value 11. Solderability J-STD-002 Leaded: method A at 235 °C, category 3 15 Good tinning as evidence by free flowing of the solder with wetting of terminations > 95 % 12. Electrical characterization - 30 - 13. Flammability UL 94 One flame application Class B 15 V-0 or V-1 are acceptable. Class B or C acc. IEC is also acceptable Revision: 08-Sep-2022 Document Number: 26073 13 For technical questions, contact: rfi@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000