IL217AT

IL215AT/216AT/217AT Vishay Semiconductors Optocoupler, Phototransistor Output, Low Input Current, with Base Connection FEATURES A 1 8 NC K 2 7 B NC 3 6 C NC 4 5 E • High current transfer ratio • Isolation test voltage, 4000 VRMS • Industry standard SOIC-8 surface mountable package • Compatible with dual wave, vapor phase and IR reflow soldering i179002 • Lead (Pb)-free component • Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC DESCRIPTION The IL215AT/IL216AT/IL217AT are optically coupled pairs with a Gallium Arsenide infrared LED and a silicon NPN phototransistor. Signal information, including a DC level, can be transmitted by the device while maintaining a high degree of electrical isolation between input and output. The IL215AT/IL216AT/IL217AT comes in a standard SOIC-8 small outline package for surface mounting which makes it ideally suited for high density applications with limited space. In addition to eliminating through hole requirements, this package conforms to standards for surface mounted devices. AGENCY APPROVALS • UL1577, file no. E52744 system code Y • CUL - file no. E52744, equivalent to CSA bulletin 5A • DIN EN 60747-5-5 available with option 1 The high CTR at low input current is designed for low power consumption requirements such as CMOS microprocessor interfaces. ORDER INFORMATION PART REMARKS IL215AT CTR > 20 %, SOIC-8 IL216AT CTR > 50 %, SOIC-8 IL217AT CTR > 100 %, SOIC-8 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Peak reverse voltage VR 6.0 V Forward continuous current IF 60 mA INPUT Power dissipation Pdiss Derate linearly from 25 °C 90 mW 1.2 mW/°C OUTPUT Collector emitter breakdown voltage BVCEO 30 V Emitter collector breakdown voltage BVECO 7.0 V Collector base breakdown voltage BVCBO 70 V ICMAX DC 50 mA ICMAX 100 mA Pdiss 150 mW 2.0 mW/°C ICMAX DC ICMAX Power dissipation Derate linearly from 25 °C www.vishay.com 324 t < 1.0 ms For technical questions, contact: optocoupler.answers@vishay.com Document Number: 83616 Rev. 1.9, 08-May-08 IL215AT/216AT/217AT Optocoupler, Phototransistor Output, Vishay Semiconductors Low Input Current, with Base Connection ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT 1s VISO 4000 VRMS Ptot 240 mW 3.2 mW/°C Tstg - 55 to + 150 °C Tamb - 55 to + 100 °C 10 s COUPLER Isolation test voltage Total package dissipation LED and detector Derate linearly from 25 °C Storage temperature Operating temperature Soldering time at 260 °C Note Tamb = 25 °C, unless otherwise specified. Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. ELECTRICAL CHARACTERISTCS PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT INPUT Forward voltage IF = 1.0 mA VF 1.0 1.5 V Reverse current VR = 6 V IR 0.1 100 µA Capacitance VR = 0 V CO 13 pF OUTPUT Collector emitter breakdown voltage IC = 10 µA BVCEO 30 V Emitter collector breakdown voltage IE = 10 µA BVECO 7.0 V Dark current collector emitter VCE = 10 V, IF = 0 A ICEO 5.0 Collector emitter capacitance VCE = 0 CCE 10 IF =1.0 mA, IC = 0.1 mA VCEsat 50 nA pF COUPLER Saturation voltage, collector emitter 0.4 V Capacitance (input to output) CIO 0.5 pF Resistance input to output RIO 100 GΩ Note Tamb = 25 °C, unless otherwise specified. Minimum and maximum values were tested requierements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. CURRENT TRANSFER RATIO PARAMETER DC current transfer ratio TEST CONDITION IF = 1.0 mA, VCE = 5.0 V PART SYMBOL MIN. TYP. IL215AT CTRDC 20 50 MAX. UNIT % IL216AT CTRDC 50 80 % IL217AT CTRDC 100 130 % PART SYMBOL MIN. TYP. SWITCHING CHARACTERISTICS PARAMETER TEST CONDITION Switching time IF = 2.0 mA, RL = 100 Ω, VCC = 10 V Document Number: 83616 Rev. 1.9, 08-May-08 ton, toff For technical questions, contact: optocoupler.answers@vishay.com 3.0 MAX. UNIT µs www.vishay.com 325 IL215AT/216AT/217AT Optocoupler, Phototransistor Output, Low Input Current, with Base Connection Vishay Semiconductors SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION SYMBOL MIN. TYP. Climatic classification (according to IEC 68 part 1) MAX. UNIT 55/100/21 Comparative tracking index CTI 175 399 VIOTM 6000 V VIORM 560 V PSO 350 mW ISI 150 mA TSI 165 Creepage °C 4 Clearance Insulation thickness, reinforced rated per IEC 60950 2.10.5.1 mm 4 mm 0.2 mm Note As per IEC 60747-5-2, §7.4.3.8.1, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. TYPICAL CHARACTERISTICS Tamb = 25 °C, unless otherwise specified 150 1.3 I CE - Collector Emitter Current (mA) VF - Forward Voltage (V) 1.4 TA = - 55 °C 1.2 TA = 25 °C 1.1 1.0 0.9 TA = 100 °C 50 VCE = 0.4 V 0.8 0 0.1 0.7 1 0.1 iil215at_01 10 100 IF - Forward Current (mA) 1 10 100 IF - LED Current (mA) iil215at_03 Fig. 1 - Forward Voltage vs. Forward Current Fig. 3 - Collector Emitter Current vs. LED Current 1.5 100 Normalized to: VCE = 10 V IF = 10 mA Normalized to: Vcb = 9.3 V 1.0 VCE = 5 V 0.5 Nlcb - Normalized Icb NCTRCE - Normalized CTRCE VCE = 5 V 100 IF = 1.0 mA 10 1 VCE = 0.4 V 0.1 0.0 0.1 iil215at_02 1 10 100 IF - LED Current (mA) Fig. 2 - Normalized Non-Saturated and Saturated CTRCE vs. LED Current www.vishay.com 326 0.1 iil215at_04 1 10 100 I F - LED Current (mA) Fig. 4 - Normalized Collector Base Photocurrent vs. LED Current For technical questions, contact: optocoupler.answers@vishay.com Document Number: 83616 Rev. 1.9, 08-May-08 IL215AT/216AT/217AT Optocoupler, Phototransistor Output, Vishay Semiconductors Low Input Current, with Base Connection 2.0 1000 NCTRce - Normalzed CTRce Vcb = 9.3 V Icb - Collector Base Current (µA) 100 10 1 0.1 0.1 1 10 Fig. 5 - Collector Base Photocurrent vs. LED Current 10 10 10 10 10 10 10 1.0 0.5 Vce = 0.4 V 1 10 100 IF - LED Current (mA) Fig. 8 - Normalized Non-Saturated and Saturated CTRCE vs. LED Current 100 5 4 Normalized to: NIce - Normalized Ice Iceo - Collector Emitter (nA) 10 Vce = 5 V IF = 1 mA iil215at_08 IF - LED Current (mA) iil215at_05 1.5 0.0 0.1 100 Vce = 5 V Normalized to: 3 2 Vce = 10 V 1 TYPICAL 0 Vce = 5 V Vce = 5 V 10 Vce = 0.4 V IF = 1 mA 1 0.1 -1 -2 - 20 0 20 40 60 80 0.01 0.1 100 1 TA - Ambient Temperature (°C) iil215at_06 10 100 I F - LED Current (mA) iil215at_09 Fig. 6 - Collector Emitter Leakage Current vs.Temperature 70 °C 1.5 Saturated hFE NhFE(sat) - Normalized 50 °C 25 °C 100 Normalized to: Normalized to: Ib = 20 µA NIcb - Normalized Icb 2.0 Vce = 10 V 1.0 Vce = 0.4 V 0.5 0.0 1 iil215at_07 10 100 1000 Ib - Base Current (µA) Fig. 7 - Normalized Saturated hFE vs. Base Current and Temperature Document Number: 83616 Rev. 1.9, 08-May-08 Fig. 9 - Normalized Non-Saturated and Saturated Collector Emitter Current vs. LED Current 10 Vce = 5 V IF = 1 mA 1 0.1 0.01 0.01 iil215at_10 0.1 1 10 100 1000 IF - LED Current (mA) Fig. 10 - Normalized Collector Base Photocurrent vs. LED Current For technical questions, contact: optocoupler.answers@vishay.com www.vishay.com 327 IL215AT/216AT/217AT Vishay Semiconductors Optocoupler, Phototransistor Output, Low Input Current, with Base Connection 1.2 1000 NhFE - Normalized hFE photocurrent (µA) Icb - Collector Base Vcb = 9.3 V 100 10 1 0.1 0.01 1 10 100 Ib = 20 µA 25 °C Vce = 10 V - 20 °C 0.8 0.6 1000 IF - LED Current (mA) 10 1 Fig. 14 - Normalized Non-Saturated hFE vs. Base Current and Temperature 100 20 10 kΩ Switching Time (µs) Vth = 1.5 V 4.7 kΩ 2 kΩ 5 0 0 5 10 15 5 TON 1.0 10K 20 F T OF 10 IF - LED Current (mA) iil215at_12 Input: IF = 10 mA Pulse width = 100 mS Duty cycle = 50 % 50 Vcc = 5 V 15 1000 100 Ib - Base Current (µA) iil215at_14 Fig. 11 - Collector Base Photocurrent vs. LED Current 10 Normalized to: 50 °C 0.4 0.1 iil215at_11 tpHL - High Low Propagation Delay (µs) 1.0 70 °C 50K 100K 500K 1M Base Emitter Resistance, RBE (W) iil215at_15 Fig. 12 - High to Low Propagation Delay vs. LED Current and Load Resistor Fig. 15 - Typical Switching Characteristics vs. Base Resistance (Saturated Operation) 80 1000 500 Switching Time (µs) 60 Delay (µs) tpLH - Low High Propagation 10 kΩ 4.7 kΩ 40 20 2 kΩ Input: IF = 10 mA Pulse with = 100 mS Duty cycle = 50 % FF TO 100 50 10 TON 5 Vcc = 5 V,Vth = 1.5 V 0 0 5 10 15 20 iil215at_13 iil215at_16 Fig. 13 - Low to High Propagation Delay vs. LED Current and Load Resistor www.vishay.com 328 1 0.1 0.5 1 5 10 50 100 Load Resistance RL (kΩ) Fig. 16 - Typical Switching Times vs. Load Resistance For technical questions, contact: optocoupler.answers@vishay.com Document Number: 83616 Rev. 1.9, 08-May-08 IL215AT/216AT/217AT Optocoupler, Phototransistor Output, Vishay Semiconductors Low Input Current, with Base Connection Input 0 VCC = 5 V Input toff ton tpdoff tpdon RL V OUT td Output tr ts tr 0 10 % 10 % 50 % 50 % 90 % 90 % iil215at_17 Fig. 17 Switching Test Circuit PACKAGE DIMENSIONS in inches (millimeters) 0.120 ± 0.005 (3.05 ± 0.13) R 0.010 (0.13) 0.240 (6.10) CL 0.154 ± 0.005 0.050 (1.27) 0.014 (0.36) (3.91 ± 0.13) 0.036 (0.91) 0.170 (4.32) 0.016 Pin one ID 0.045 (1.14) (0.41) 0.260 (6.6) 7° 0.058 ± 0.005 0.192 ± 0.005 0.015 ± 0.002 (4.88 ± 0.13) 40° (1.49 ± 0.13) (0.38 ± 0.05) 0.004 (0.10) 0.125 ± 0.005 0.008 (0.20) 0.008 (0.20) (3.18 ± 0.13) 5° max. 0.050 (1.27) typ. 0.020 ± 0.004 ISO method A 0.021 (0.53) R 0.010 Lead coplanarity (0.25) max. ± 0.0015 (0.04) max. (0.51 ± 0.10) 2 places i178003 Document Number: 83616 Rev. 1.9, 08-May-08 For technical questions, contact: optocoupler.answers@vishay.com www.vishay.com 329 IL215AT/216AT/217AT Vishay Semiconductors Optocoupler, Phototransistor Output, Low Input Current, with Base Connection OZONE DEPLETING SUBSTANCES POLICY STATEMENT It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively. 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA. 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany www.vishay.com 330 For technical questions, contact: optocoupler.answers@vishay.com Document Number: 83616 Rev. 1.9, 08-May-08 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1