IRL630S, SiHL630S
www.vishay.com
Vishay Siliconix
Power MOSFET
FEATURES
D
•
•
•
•
•
•
•
•
D2PAK (TO-263)
G
G D
S
S
Note
* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non RoHS-compliant. For
example, parts with lead (Pb) terminations are not RoHS-compliant.
Please see the information / tables in this datasheet for details
N-Channel MOSFET
PRODUCT SUMMARY
VDS (V)
RDS(on) ()
200
VGS = 5 V
40
Qgs (nC)
5.5
Qgd (nC)
24
Configuration
DESCRIPTION
0.40
Qg max. (nC)
Surface-mount
Available in tape and reel
Dynamic dv/dt rating
Available
Repetitive avalanche rated
Logic-level gate drive
Available
RDS(on) specified at VGS = 4 V and 5 V
150 °C operating temperature
Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
Third generation power MOSFETs from Vishay provide the
designer with the best combination of fast switching,
ruggedized device design, low on-resistance and
cost-effectiveness.
The D2PAK (TO-263) is a surface-mount power package
capable of accommodating die size up to HEX-4. It provides
the highest power capability and the lowest possible
on-resistance in any existing surface-mount package. The
D2PAK (TO-263) is suitable for high current applications
because of its low internal connection resistance and can
dissipate up to 2.0 W in a typical surface-mount application.
Single
ORDERING INFORMATION
Package
Lead (Pb)-free and halogen-free
Lead (Pb)-free
Note
a. See device orientation
D2PAK (TO-263)
SiHL630S-GE3
IRL630SPbF
D2PAK (TO-263)
SiHL630STRR-GE3 a
IRL630STRRPbF a
D2PAK (TO-263)
SiHL630STRL-GE3 a
IRL630STRLPbF a
ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless otherwise noted)
PARAMETER
Drain-source voltage
Gate-source Voltage
Continuous drain current
Pulsed drain current a
Linear derating factor
Linear derating factor (PCB mount) e
Single pulse avalanche energy b
Avalanche current a
Repetitive avalanche energy a
Maximum power dissipation
Maximum power dissipation (PCB mount) e
Peak diode recovery dv/dt c
Operating junction and storage temperature range
Soldering recommendations (peak temperature) d
SYMBOL
VDS
VGS
VGS at 5 V
TC = 25 °C
TC = 100 °C
ID
IDM
EAS
IAR
EAR
TC = 25 °C
TA = 25 °C
PD
dv/dt
TJ, Tstg
For 10 s
LIMIT
200
± 10
9.0
5.7
36
0.59
0.025
250
9.0
7.4
74
3.1
5.0
-55 to +150
300
UNIT
V
A
W/°C
mJ
A
mJ
W
V/ns
°C
Notes
a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11)
b. VDD = 25 V, starting TJ = 25 °C, L = 4.6 mH, Rg = 25 , IAS = 9.0 A (see fig. 12)
c. ISD 9.0 A, di/dt 120 A/μs, VDD VDS, TJ 150 °C
d. 1.6 mm from case
e. When mounted on 1" square PCB (FR-4 or G-10 material)
S20-0684-Rev. D, 07-Sep-2020
Document Number: 90390
1
For technical questions, contact: hvm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IRL630S, SiHL630S
www.vishay.com
Vishay Siliconix
THERMAL RESISTANCE RATINGS
PARAMETER
SYMBOL
TYP.
MAX.
Maximum Junction-to-Ambient
RthJA
-
62
Maximum Junction-to-Ambient
(PCB Mount)a
RthJA
-
40
Maximum Junction-to-Case (Drain)
RthJC
-
1.7
UNIT
°C/W
Note
a. When mounted on 1" square PCB (FR-4 or G-10 material)
SPECIFICATIONS (TJ = 25 °C, unless otherwise noted)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN.
TYP.
MAX.
UNIT
Static
Drain-source breakdown voltage
VDS temperature coefficient
Gate-source threshold voltage
VDS
VGS = 0, ID = 250 μA
200
-
-
V
VDS/TJ
Reference to 25 °C, ID = 1 mA
-
0.27
-
V/°C
VGS(th)
VDS = VGS, ID = 250 μA
1.0
-
2.0
V
Gate-source leakage
IGSS
VGS = ± 10 V
-
-
± 100
nA
Zero gate voltage drain current
IDSS
VDS = 200 V, VGS = 0 V
-
-
25
VDS = 160 V, VGS = 0 V, TJ = 125 °C
-
-
250
Drain-source on-state resistance
Forward transconductance
RDS(on)
VGS = 5.0 V
ID = 5.4 A b
-
-
0.40
VGS = 4.0 V
ID = 4.5 A b
-
-
0.50
gfs
VDS = 50 V, ID = 5.4 A b
4.8
-
-
VGS = 0 V,
VDS = 25 V,
f = 1.0 MHz, see fig. 5
-
1100
-
-
220
-
-
70
-
-
-
40
μA
S
Dynamic
Input capacitance
Ciss
Output capacitance
Coss
Reverse transfer capacitance
Crss
Total gate charge
Qg
Gate-source charge
Qgs
Gate-drain charge
Qgd
Turn-on delay time
td(on)
Rise time
tr
Turn-off delay time
td(off)
Fall time
VGS = 10 V
ID = 9.0 A, VDS = 160 V,
see fig. 6 and 13 b
VDD = 100 V, ID = 9.0 A,
Rg = 6.0 , RD = 11 , see fig. 10 b
tf
Internal drain inductance
LD
Internal source inductance
LS
Between lead,
6 mm (0.25") from
package and center of
die contact
-
-
5.5
-
-
24
-
8.0
-
-
57
-
-
38
-
-
33
-
-
4.5
-
-
7.5
-
-
-
9.0
-
-
36
pF
nC
ns
D
nH
G
S
Drain-Source Body Diode Characteristics
Continuous source-drain diode current
Pulsed diode forward current
a
Body diode voltage
IS
ISM
VSD
Body diode reverse recovery time
trr
Body diode reverse recovery charge
Qrr
Forward turn-on time
ton
MOSFET symbol
showing the
integral reverse
p - n junction diode
D
A
G
S
TJ = 25 °C, IS = 9.0 A, VGS = 0 V b
TJ = 25 °C, IF = 9.0 A, di/dt = 100 A/μs b
-
-
2.0
V
-
230
350
ns
-
1.7
2.6
μC
Intrinsic turn-on time is negligible (turn-on is dominated by LS and LD)
Notes
a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11)
b. Pulse width 300 μs; duty cycle 2 %
S20-0684-Rev. D, 07-Sep-2020
Document Number: 90390
2
For technical questions, contact: hvm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IRL630S, SiHL630S
www.vishay.com
Vishay Siliconix
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
100
100
VGS
7.50V
5.00V
4.00V
3.50V
3.00V
2.75V
2.50V
BOTTOM 2.25V
I D , Drain-to-Source Current (A)
I , Drain-to-Source Current (A)
D
TOP
10
1
2.25V
20μs PULSE WIDTH
Tc = 25°C
0.1
0.1
1
10
100
A
10
TJ = 150°C
1
TJ = 25°C
0.1
2.0
VDS , Drain-to-Source Voltage (V)
R DS(on) , Drain-to-Source On Resistance
(Normalized)
VGS
7.50V
5.00V
4.00V
3.50V
3.00V
2.75V
2.50V
BOTTOM 2.25V
I , Drain-to-Source Current (A)
D
10
2.25V
1
20μs PULSE WIDTH
TC = 150°C
0.1
1
10
100
VDS , Drain-to-Source Voltage (V)
Fig. 2 - Typical Output Characteristics, TC = 150 °C
S20-0684-Rev. D, 07-Sep-2020
3.0
3.5
4.0
4.5
A
5.0
Fig. 3 - Typical Transfer Characteristics
TOP
0.1
2.5
VGS , Gate-to-Source Voltage (V)
Fig. 1 - Typical Output Characteristics, TC = 25 °C
100
V DS = 50V
20μs PULSE WIDTH
0.01
A
2.5
ID = 9.0A
2.0
1.5
1.0
0.5
0.0
-60 -40 -20
VGS = 5.0V
0
20
40
60
A
80 100 120 140 160
TJ , Junction Temperature (°C)
Fig. 4 - Normalized On-Resistance vs. Temperature
Document Number: 90390
3
For technical questions, contact: hvm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IRL630S, SiHL630S
www.vishay.com
100
2000
V GS = 0V,
f = 1MHz
C iss = C gs + C gd , Cds SHORTED
C rss = C gd
C oss = C ds + C gd
ISD , Reverse Drain Current (A)
C, Capacitance (pF)
Vishay Siliconix
1500
Ciss
1000
C oss
500
10
TJ = 150°C
TJ = 25°C
1
Crss
A
0
1
10
VGS = 0V
0.1
0
100
V DS , Drain-to-Source Voltage (V)
1.2
A
1.6
Fig. 7 - Typical Source-Drain Diode Forward Voltage
100
I D = 9.0A
OPERATION IN THIS AREA LIMITED
BY R DS(on)
VDS = 160V
VDS = 100V
VDS = 40V
8
10μs
I D , Drain Current (A)
V GS , Gate-to-Source Voltage (V)
0.8
V SD , Source-to-Drain Voltage (V)
Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage
10
0.4
6
4
10
100μs
1ms
1
10ms
100ms
2
FOR TEST CIRCUIT
SEE FIGURE 13
0
0
10
20
30
40
A
Q G , Total Gate Charge (nC)
Fig. 6 - Typical Gate Charge vs. Gate-to-Source Voltage
S20-0684-Rev. D, 07-Sep-2020
T C = 25°C
T J = 150°C
Single Pulse
0.1
1
10
100
1000
VDS , Drain-to-Source Voltage (V)
Fig. 8 - Maximum Safe Operating Area
Document Number: 90390
4
For technical questions, contact: hvm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IRL630S, SiHL630S
www.vishay.com
Vishay Siliconix
RD
VDS
10
ID, Drain Current (Amps)
VGS
D.U.T.
Rg
8
+
- VDD
5V
6
Pulse width ≤ 1 µs
Duty factor ≤ 0.1 %
Fig. 10a - Switching Time Test Circuit
4
VDS
2
90 %
0
25
50
75
100
A
125
150
TC , Case Temperature (°C)
10 %
VGS
td(on)
Fig. 9 - Maximum Drain Current vs. Case Temperature
td(off) tf
tr
Fig. 10b - Switching Time Waveforms
Thermal Response (Z thJC )
10
1
D = 0.50
0.20
0.10
0.1
PD M
0.05
t
0.02
0.01
1
t
N o te s :
1 . D u ty fa c to r D = t
SINGLE PULSE
(THERMAL RESPONSE)
1
/ t
2
2 . P e a k TJ = P D M x Z th J C + T C
0.01
0.00001
0.0001
0.001
0.01
0.1
2
1
A
10 A
t 1 , Rectangular Pulse Duration (sec)
Fig. 11 - Maximum Effective Transient Thermal Impedance, Junction-to-Case
S20-0684-Rev. D, 07-Sep-2020
Document Number: 90390
5
For technical questions, contact: hvm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IRL630S, SiHL630S
www.vishay.com
Vishay Siliconix
L
VDS
VDS
Vary tp to obtain
required IAS
tp
VDD
Rg
D.U.T.
+
-
I AS
V DD
VDS
5V
0.01 Ω
tp
IAS
EAS , Single Pulse Avalanche Energy (mJ)
Fig. 12a - Unclamped Inductive Test Circuit
Fig. 12b - Unclamped Inductive Waveforms
600
ID
9.0A
5.7A
BOTTOM 4.0A
TOP
500
400
300
200
100
0
VDD = 50V
25
50
A
75
100
125
150
Starting TJ , Juntion Temperature (°C)
Fig. 12c - Maximum Avalanche Energy vs. Drain Current
Current regulator
Same type as D.U.T.
50 kΩ
QG
5V
12 V
0.2 µF
0.3 µF
QGS
QGD
+
D.U.T.
VG
-
VDS
VGS
3 mA
Charge
IG
ID
Current sampling resistors
Fig. 13a - Basic Gate Charge Waveform
S20-0684-Rev. D, 07-Sep-2020
Fig. 13b - Gate Charge Test Circuit
Document Number: 90390
6
For technical questions, contact: hvm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IRL630S, SiHL630S
www.vishay.com
Vishay Siliconix
Peak Diode Recovery dV/dt Test Circuit
+
D.U.T.
Circuit layout considerations
• Low stray inductance
• Ground plane
• Low leakage inductance
current transformer
+
+
-
-
Rg
•
•
•
•
dV/dt controlled by Rg
Driver same type as D.U.T.
ISD controlled by duty factor “D”
D.U.T. - device under test
+
-
VDD
Driver gate drive
P.W.
Period
D=
P.W.
Period
VGS = 10 Va
D.U.T. lSD waveform
Reverse
recovery
current
Body diode forward
current
dI/dt
D.U.T. VDS waveform
Diode recovery
dV/dt
Re-applied
voltage
Inductor current
VDD
Body diode forward drop
Ripple ≤ 5 %
ISD
Note
a. VGS = 5 V for logic level devices
Fig. 14 - For N-Channel
Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon
Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and
reliability data, see www.vishay.com/ppg?90390.
S20-0684-Rev. D, 07-Sep-2020
Document Number: 90390
7
For technical questions, contact: hvm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Package Information
Vishay Siliconix
TO-263AB (HIGH VOLTAGE)
A
(Datum A)
3
A
4
4
L1
B
A
E
c2
H
Gauge
plane
4
0° to 8°
5
D
B
Detail A
Seating plane
H
1
2
C
3
C
L
L3
L4
Detail “A”
Rotated 90° CW
scale 8:1
L2
B
A1
B
A
2 x b2
c
2xb
E
0.010 M A M B
± 0.004 M B
2xe
Plating
5
b1, b3
Base
metal
c1
(c)
D1
4
5
(b, b2)
Lead tip
MILLIMETERS
DIM.
MIN.
MAX.
View A - A
INCHES
MIN.
4
E1
Section B - B and C - C
Scale: none
MILLIMETERS
MAX.
DIM.
MIN.
INCHES
MAX.
MIN.
MAX.
A
4.06
4.83
0.160
0.190
D1
6.86
-
0.270
-
A1
0.00
0.25
0.000
0.010
E
9.65
10.67
0.380
0.420
6.22
-
0.245
-
b
0.51
0.99
0.020
0.039
E1
b1
0.51
0.89
0.020
0.035
e
b2
1.14
1.78
0.045
0.070
H
14.61
15.88
0.575
0.625
b3
1.14
1.73
0.045
0.068
L
1.78
2.79
0.070
0.110
2.54 BSC
0.100 BSC
c
0.38
0.74
0.015
0.029
L1
-
1.65
-
0.066
c1
0.38
0.58
0.015
0.023
L2
-
1.78
-
0.070
c2
1.14
1.65
0.045
0.065
L3
D
8.38
9.65
0.330
0.380
L4
0.25 BSC
4.78
5.28
0.010 BSC
0.188
0.208
ECN: S-82110-Rev. A, 15-Sep-08
DWG: 5970
Notes
1. Dimensioning and tolerancing per ASME Y14.5M-1994.
2. Dimensions are shown in millimeters (inches).
3. Dimension D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005") per side. These dimensions are measured at the
outmost extremes of the plastic body at datum A.
4. Thermal PAD contour optional within dimension E, L1, D1 and E1.
5. Dimension b1 and c1 apply to base metal only.
6. Datum A and B to be determined at datum plane H.
7. Outline conforms to JEDEC outline to TO-263AB.
Document Number: 91364
Revision: 15-Sep-08
www.vishay.com
1
AN826
Vishay Siliconix
RECOMMENDED MINIMUM PADS FOR D2PAK: 3-Lead
0.420
0.355
0.635
(16.129)
(9.017)
(10.668)
0.145
(3.683)
0.135
(3.429)
0.200
0.050
(5.080)
(1.257)
Recommended Minimum Pads
Dimensions in Inches/(mm)
Return to Index
Document Number: 73397
11-Apr-05
www.vishay.com
1
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 01-Jan-2022
1
Document Number: 91000