LH1502BACTR

LH1502BAC, LH1502BACTR, LH1502BB www.vishay.com Vishay Semiconductors Dual 1 Form A/B, C Solid-State Relay FEATURES S1 DIP • Current limit protection S1' • Isolation test voltage 3750 VRMS S2 • Typical RON 20 Ω S2' • Load voltage 350 V • Load current 150 mA S1 8 S1' S2 7 6 • High surge capability S2' 5 • Clean bounce free switching SMD • Low power consumption • SMD lead available on tape and reel 1 2 3 • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 4 i179034_2 APPLICATIONS • General telecom switching DESCRIPTION - On / off hook control The LH1502 relays contain normally open and normally closed switches that can be used independently as a 1 form A and 1 form B relay, or when used together, as a 1 form C relay. The relays are constructed as a multi-chip hybrid device. Actuation control is via an infrared LED. The output switch is a combination of a photodiode array with MOSFET switches and control circuity. - Ring delay - Dial pulse - Ground start - Ground fault protection • Instrumentation • Industrial controls AGENCY APPROVALS • UL1577, file no. E52744 system code H, double protection • CSA, certification 093751 • DIN EN, 60747-5-2 (VDE 0884)/60747-5-5 (pending), available with option 1 • FIMKO, 25419 ORDERING INFORMATION L H 1 5 PART NUMBER PACKAGE SMD-8, tubes SMD-8, tape and reel DIP-8, tubes Rev. 1.6, 31-Jul-17 0 2 B ELECTR. VARIATION # # PACKAGE CONFIG. T DIP R TAPE AND REEL 7.62 mm SMD > 0.1 mm UL, CSA, FIMKO LH1502BAC LH1502BACTR LH1502BB Document Number: 83806 1 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1502BAC, LH1502BACTR, LH1502BB www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT IF 50 mA IR ≤ 10 μA VR 8 V IL ≤ 50 μA VL 350 V IL 150 mA IP (3) IP 350 INPUT LED continuous forward current LED reverse voltage OUTPUT DC or peak AC load voltage Continuous DC load current (form C operation) Peak load current, form A t = 100 ms Peak load current (single shot), form B mA SSR Ambient operating temperature range Tamb -40 to +85 °C Storage temperature range Tstg -40 to +125 °C Pin soldering temperature (1) Input to output isolation test voltage t = 10 s max. Tsld 260 °C t = 1 s, IISO = 10 μA max. VISO 3750 VRMS 1600 V 600 mW Pole-to-pole isolation voltage (S1 to S2) (2), (dry air, dust free, at sea level) Output power dissipation (continuous) Pdiss Notes • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability (1) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through hole devices (DIP) (2) Breakdown occurs between the output pins external to the package (3) Refer to current limit performance application note for a discussion on relay operation during transient currents ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT INPUT LED forward current, switch turn-on (NO) IL = 100 mA, t = 10 ms IFon - 0.6 2 mA LED forward current, switch turn-off (NO) VL = ± 300 V IFoff 0.4 0.5 - mA LED forward current, switch turn-on (NC) IL = 300 mA, t = 10 ms IFon 0.2 0.9 - mA LED forward current, switch turn-off (NC) VL = ± 300 V IFoff - 1 2 mA IF = 10 mA VF 1.15 1.26 1.45 V IF = 5 mA (NO), IF = 0 mA (NC), IL = 50 mA (NC) RON 12 20 25 Ω IF = 0 mA, VL = ± 100 V ROFF 0.35 5000 - GΩ LED forward voltage OUTPUT On-resistance (NO, NC) Off-resistance (NO) Off-resistance (NC) IF = 5 mA, VL = ± 100 V ROFF 0.1 1.4 - GΩ IF = 5 mA, t = 5 ms, VL = ± 5 V ILMT 270 290 380 mA Off-state leakage current (NO) IF = 0 mA, VL = ± 100 V IO - 0.02 1000 nA Off-state leakage current (NC) IF = 5 mA, VL = ± 100 V IO - 0.07 1 μA IF = 0 mA (NO), IF = 5 mA (NC), VL = ± 200 V IO - - 1 μA Output capacitance (NO) IF = 0 mA, VL = 50 V CO - 50 - pF Output capacitance (NC) IF = 5 mA, VL = 50 V CO - 50 - pF VISO = 1 V CIO - 3 - pF Current limit (NO) Off-state leakage current (NO, NC) TRANSFER Capacitance (input to output) Note • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements Rev. 1.6, 31-Jul-17 Document Number: 83806 2 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1502BAC, LH1502BACTR, LH1502BB www.vishay.com Vishay Semiconductors SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Turn-on time (NO) IF = 10 mA, IL = 37.5 mA, VL = 150 V ton 0.2 3.2 6 ms Turn-on time (NC) IF = 10 mA, IL = 37.5 mA, VL = 150 V ton 0.2 3.8 6 ms Turn-off time (NO) IF = 10 mA, IL = 37.5 mA, VL = 150 V toff - 1.6 3 ms Turn-off time (NC) IF = 10 mA, IL = 37.5 mA, VL = 150 V toff - 0.8 3 ms TRANSFER TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 150 150 5.0 mA 5.0 mA 120 Load Current (mA) Load Current (mA) 120 90 60 30 90 50 30 0 Form A - 40 ilh1502bb_00 - 20 0 20 40 60 80 Ambient Temperature (°C) Fig. 1 - Recommended Operating Conditions Rev. 1.6, 31-Jul-17 0 Form B - 40 ilh1502bb_01 - 20 0 20 40 60 Ambient Temperature (°C) 80 Fig. 2 - Recommended Operating Conditions Document Number: 83806 3 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1502BAC, LH1502BACTR, LH1502BB www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS (in millimeters) DIP-8 10.06 max. 9.65 ± 0.15 7.62 typ. 0.46 typ. 9.14 typ. .10 0.25 ± 0 7° typ. 2.54 nom. 7.24 typ. 3.25 ± 0.25 3.30 ± 0.20 6.35 ± 0.15 8.08 typ. 8 7 6 5 1 2 3 4 pin one ID Technical drawing according to DIN specification SMD-8 9.78 ± 0.25 7.62 typ. 10.06 max. 0.18 ± 0.08 3.30 ± 0.20 0.25 ± 0.10 6.35 ± 0.15 9.65 ± 0.15 0.46 typ. 2.54 nom. 8.08 typ. 0.65 ± 0.20 8.00 min. Leads coplanarity 0.1 max. 7 6 5 1 2 3 4 2.54 pin one ID .25 R0 1.78 8 0.76 Recommended footprint 8.00 min. 11.05 1.52 Technical drawing according to DIN specification PACKAGE MARKING (example) LH1502 V YWW H 68 Note • Tape and reel suffix (TR) is not part of the package marking Rev. 1.6, 31-Jul-17 Document Number: 83806 4 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Footprint and Schematic Information www.vishay.com Vishay Semiconductors Footprint and Schematic Information for LH1502BAC, LH1502BACTR, LH1502BB The footprint and schematic symbols for the following parts can be accessed using the associated links. They are available in Eagle, Altium, KiCad, OrCAD / Allegro, Pulsonix, and PADS. Note that the 3D models for these parts can be found on the Vishay product page. PART NUMBER FOOTPRINT / SCHEMATIC LH1502BAC LH1502BACTR www.snapeda.com/parts/LH1502BAC/Vishay/view-part www.snapeda.com/parts/LH1502BACTR/Vishay/view-part LH1502BB www.snapeda.com/parts/LH1502BB/Vishay/view-part For technical issues and product support, please contact optocoupleranswers@vishay.com. DIP SMD i179034_2 Rev. 1.0, 09-May-17 Document Number: 84470 1 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2019 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2019 1 Document Number: 91000