M55342M01B220GRWSV

E/H (Military M/D55342) www.vishay.com Vishay Dale Thin Film QPL MIL-PRF-55342 Qualified Thin Film Resistor, Surface-Mount Chip FEATURES • Established reliability, “S” and “V” failure rate level (10 ppm), C = 2 • High purity alumina substrate • Wraparound termination featuring a tenacious adhesion layer covered with an electroplated nickel barrier layer for +150 °C operating conditions • Very low noise and voltage coefficient (< -25 dB, 0.5 ppm/V) LINKS TO ADDITIONAL RESOURCES • Non-inductive 3D 3D • Laser-trimmed tolerances ± 0.1 % 3D Models • Wraparound resistance less than 0.010 Ω typical Thin Film Mil chip resistors feature all sputtered wraparound termination for excellent adhesion and dimensional uniformity. They are ideal in applications requiring stringent performance requirements. Established reliability is assured through 100 % screening and extensive environmental lot testing. • In-lot tracking less than 5 ppm/°C • Complete MIL-testing available in-house • Antistatic waffle pack or tape and reel packaging available • Military / aerospace / QPL CONSTRUCTION Passivation TYPICAL PERFORMANCE Resistor Film Solder Coating ABSOLUTE Nickel Barrier High Purity Alumina Substrate Adhesion Layer TCR 25 TOL. 0.1 STANDARD ELECTRICAL SPECIFICATIONS TEST Material Resistance Range TCR: Absolute Tolerance: Absolute Stability: Absolute Stability: Ratio Voltage Coefficient SPECIFICATIONS CONDITIONS Tamelox resistor film (passivated nichrome) - 10 Ω to 6.19 MΩ - ± 25 ppm/°C to ± 300 ppm/°C -55 °C to +125 °C ± 0.1 %, ± 0.25 %, ± 0.5 %, ± 1 %, ± 2 %, 5 %, ± 10 % +25 °C ΔR ± 0.02 % 2000 h at +70 °C - - 0.1 ppm/V - 30 V to 200 V - Operating Temperature Range -65 °C to +150 °C - Storage Temperature Range -65 °C to +150 °C - < - 25 dB - ΔR ± 0.01 % 1 year at +25 °C Working Voltage Noise Shelf Life Stability: Absolute Revision: 15-Nov-2021 Document Number: 60018 1 For technical questions, contact: thinfilm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 E/H (Military M/D55342) www.vishay.com Vishay Dale Thin Film COMPONENT RATINGS CASE SIZE POWER RATING (mW) RESISTANCE RANGE (Ω) BY CHARACTERISTICS TOLERANCE WORKING VOLTAGE E E H, K, L, M H, K, L, M (V) (0.1 %, 0.25 %, 0.5 %) (1 %, 2 %, 5 %, 10 %) (0.1 %, 0.25 %, 0.5 %) (1 %, 2 %, 5 %, 10 %) M55342/01 50 40 49.9 to 150K 49.9 to 150K 20 to 150K 20 to 150K M55342/02 125 40 49.9 to 301K 49.9 to 301K 20 to 301K 20 to 301K M55342/03 200 75 49.9 to 649K 49.9 to 649K 10 to 649K 10 to 649K M55342/04 150 125 49.9 to 1.69M 49.9 to 1.69M 10 to 1.69M 10 to 1.69M M55342/05 225 175 49.9 to 3.16M 49.9 to 3.16M 10 to 3.16M 10 to 3.16M M55342/06 150 50 49.9 to 475K 49.9 to 475K 10 to 475K 10 to 475K D55342/07 250 100 49.9 to 1.5M 49.9 to 1.5M 10 to 1.5M 10 to 1.5M M55342/08 800 150 49.9 to 4.02M 49.9 to 4.02M 10 to 4.02M 10 to 4.02M M55342/09 1000 200 49.9 to 6.19M 49.9 to 6.19M 10 to 6.19M 10 to 6.19M M55342/10 500 75 49.9 to 1M 49.9 to 1M 49.9 to 1M 49.9 to 1M M55342/11 50 30 49.9 to 100K 49.9 to 100K 20 to 100K 20 to 100K M55342/12 100 50 49.9 to 258K 49.9 to 261K 10 to 258K 10 to 261K Note • Values listed are a guide, refer to MIL spec for value / tolerance allowance DIMENSIONS in inches D W T E L CASE SIZE TERM. L W T D E M55342/01 B 0.055 ± 0.006 0.025 ± 0.005 0.010 to 0.033 0.010 ± 0.005 0.015 ± 0.005 M55342/02 B 0.055 ± 0.006 0.050 ± 0.005 0.010 to 0.033 0.010 ± 0.005 0.015 ± 0.005 M55342/03 B 0.105 ± 0.007 0.050 ± 0.005 0.010 to 0.033 0.015 ± 0.005 0.015 ± 0.005 M55342/04 B 0.155 ± 0.007 0.050 ± 0.005 0.015 to 0.033 0.015 ± 0.005 0.015 ± 0.005 M55342/05 B 0.230 ± 0.007 0.075 ± 0.005 0.010 to 0.033 0.020 ± 0.005 0.020 ± 0.005 M55342/06 B 0.080 ± 0.006 0.050 ± 0.005 0.010 to 0.033 0.016 ± 0.008 0.015 ± 0.005 D55342/07 B 0.126 ± 0.008 0.063 ± 0.005 0.010 to 0.033 M55342/08 B 0.209 + 0.009/- 0.018 0.098 ± 0.005 0.010 to 0.033 M55342/09 B 0.259 + 0.009/- 0.015 0.124 ± 0.005 0.010 to 0.033 0.020 ± 0.005 0.020 ± 0.005 M55342/10 B 0.105 ± 0.007 0.100 ± 0.005 0.010 to 0.033 0.015 ± 0.005 0.015 ± 0.005 M55342/11 B 0.040 ± 0.005 0.022 ± 0.005 0.010 to 0.033 0.010 ± 0.005 0.010 ± 0.005 M55342/12 B 0.064 ± 0.006 0.032 ± 0.005 0.010 to 0.033 0.012 ± 0.005 0.015 ± 0.005 Revision: 15-Nov-2021 0.020 + 0.005 / - 0.010 0.020 + 0.005 / - 0.010 0.020 ± 0.005 0.020 ± 0.005 Document Number: 60018 2 For technical questions, contact: thinfilm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 E/H (Military M/D55342) www.vishay.com Vishay Dale Thin Film ENVIRONMENTAL TESTS MIL-PRF-55342 LIMITS (ΔR ±) VISHAY PERFORMANCE (ΔR ±) Thermal Shock 0.1 % 0.020 % Low Temperature Operation 0.1 % 0.025 % Short Time Overload 0.1 % 0.050 % High Temperature Exposure 0.1 % 0.009 % Resistance to Bonding 0.2 % 0.006 % Moisture Resistance 0.2 % 0.004 % ENVIRONMENTAL TEST TCR ± 25 ppm/°C < 15 ppm/°C Life (2000 h at + 70 °C) 0.5 % 0.02 % Life (10 000 h at + 70 °C) 2.0 % 0.04 % MECHANICAL SPECIFICATIONS Resistive Element Tamelox Substrate Material Alumina Chip Terminations Fused Solder FSCM CAGE # - 57489 Solder over nickel Tin / lead solder alloy DERATING Axis Title 10000 80 1000 60 1st line 2nd line 2nd line Percent of Rated Wattage 100 40 100 20 10 0 -75 -50 -25 0 25 50 75 100 125 150 175 Ambient Temperature (°C) Revision: 15-Nov-2021 Document Number: 60018 3 For technical questions, contact: thinfilm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 E/H (Military M/D55342) www.vishay.com Vishay Dale Thin Film GLOBAL PART NUMBER INFORMATION New Global Part Numbering: M55342E06B1C00RTS M 5 5 3 TCR GLOBAL MODEL CHARACTERISTIC M55342 E = 25 ppm/°C H = 50 ppm/°C or D55342 K = 100 ppm/°C (/07 size L = 200 ppm/°C M = 300 ppm/°C only) 4 CASE SIZE 2 E 0 6 TERMINATION B 1 C 0 0 FAILURE RATE OHMIC VALUE 01 = 0502 B = solderable Three digits and a letter. Letter identifies tolerance, acts as 02 = 0505 multiplier and decimal locator. 03 = 1005 04 = 1505 MULTIPLIER 05 = 2208 Tolerance 1 Ω 1 kΩ 1 MΩ 06 = 0705 07 = 1206 0.1 % A B C 08 = 2010 0.25 % R U V 09 = 2512 0.5 % W Y Z 10 = 1010 11 = 0402 1% D E F 12 = 0603 2% G H T 5% J K L 10 % M N P M = 1.0 % per 1000 h P = 0.1 % per 1000 h R = 0.01 % per 1000 h U = 0.01 % per 1000 h (3) S = 0.001 % per 1000 h V = 0.001 % per 1000 h (3) C = non ER version R T S PACKAGING V THIN FILM CODE (1) V Standard Packaging: for BS = BULK K, L, and M 25 min., 1 mult. TCR WS = WAFFLE W/tolerance 25 min., 1 mult. ≥1% W0 = WAFFLE M = part 100 min.,100 mult. marked (2) TAPE AND REEL T0 = 100 min., 100 mult. T1 = 1000 min., 1000 mult. T3 = 300 min., 300 mult. T5 = 500 min., 500 mult. TF = full reel (2K, 4K, or 5K dependent on case size) per tape and reel document 60034 TS = 25 min., 1 mult. Special Packaging: WAFFLE WI = 25 min., 1 mult. (item single lot date code) WP = 25 min., 1 mult. (package unit single lot date code) TAPE AND REEL TI = 25 min., 1 mult. (item single lot date code) TP = 25 min., 1 mult. (package unit single lot date code) Historical Part Number Example: M55342K06B5E60R (for reference purposes only) M55342 K 06 B 5E60 R SERIES TCR CHARACTERISTIC CASE SIZE TERMINATION VALUE AND TOLERANCE FAILURE RATE Notes • For M/D55342 T-level failure rate options please see VTF E/H (T-level) datasheet: www.vishay.com/ppg?60060 (1) Only add a V at the end of part number to specify Vishay Dale Thin Film for K, L and M TCR and tolerance 1 % and higher (2) Option 1 marking only. Case sizes 01, 02, 11, and 12 not available due to size (3) Failure rate U and V require group A and B testing on a production lot basis Revision: 15-Nov-2021 Document Number: 60018 4 For technical questions, contact: thinfilm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2023 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2023 1 Document Number: 91000