M8340102K4701GAD04

MDM (Military M83401/01 and /02) www.vishay.com Vishay Dale Thick Film Resistor Networks, Military, MIL-PRF-83401 Qualified, Type RZ010 and RZ020 Dual-In-Line, Molded DIP FEATURES • • • • • • Isolated, bussed and dual terminator schematics available MIL-PRF-83401 qualified Epoxy molded construction All device leads are hot-solder dipped Available in tube pack TCR available in “K” (± 100 ppm/°C) or “M” (± 300 ppm/°C) depending on style • 100 % screen tested per group A, subgroup 1 of MIL-PRF-83401 • All devices are capable of passing the MIL-STD-202, method 210, condition D, “Resistance to Soldering Heat” test STANDARD ELECTRICAL SPECIFICATIONS POWER POWER VISHAY RATING MIL RATING RESISTANCE TOLERANCE (2) MIL DALE SPEC. SCHEMATIC ELEMENT PACKAGE RANGE MODEL/  STYLE SHEET ±% P70 °C P70 °C  PIN NO. W W 01 (B) 0.10 1.30 10 to 1M MDM14 RZ010 01 03 (A) 0.20 1.40 10 to 1M 1, 2, 5 05 (J) 0.05 1.20 Consult factory 01 (B) 0.10 1.50 10 to 1M 03 (A) 0.20 1.60 10 to 1M 1, 2, 5 MDM16 RZ020 02 05 (J) 0.05 1.40 Consult factory Notes (1) K = ± 100 ppm/°C; M = ± 300 ppm/°C (2) ± 2 % standard, ± 1 % and ± 5 % available TEMPERATURE COEFFICIENT (1) (-55 °C to +125 °C) ± ppm/°C WEIGHT g 100, 300 1.3 100, 300 1.5 GLOBAL PART NUMBER INFORMATION New Global Part Numbering: M8340101M2201GBD04 (preferred part numbering format) M 8 3 4 0 1 0 1 M 2 2 0 1 RESISTANCE TOLERANCE VALUE F=±1% M83401 01 = 14 pin K = 100 ppm 3 digit significant G=±2% 02 = 16 pin M = 300 ppm figure, followed J=±5% by a multiplier 10R0 = 10  3302 = 33 k 1004 = 1 M Historical Part Number Example: M8340101M2201GB (will continue to be accepted) MIL STYLE SPEC SHEET CHARACTERISTIC G B D 0 4 SCHEMATIC PACKAGING A = Isolated B = Bussed D04 = Tin/lead, tube DSL = Tin/lead, tube, single lot date code M83401 01 M 2201 G B D04 MIL STYLE SPEC SHEET CHARACTERISTIC RESISTANCE VALUE TOLERANCE SCHEMATIC PACKAGING New Global Part Numbering: M8340102KA001GJD04 (preferred part numbering format) M 8 3 4 0 1 0 2 K A 0 0 1 RESISTANCE TOLERANCE VALUE F=±1% M83401 01 = 14 pin K = 100 ppm Per Std. G=±2% 02 = 16 pin M = 300 ppm MIL. Spec. J=±5% (see Impedance Codes table) Historical Part Number Example: M8340102KA001GJ (will continue to be accepted) MIL STYLE SPEC SHEET M83401 MIL STYLE 02 SPEC SHEET CHARACTERISTIC G J D 0 4 SCHEMATIC PACKAGING J = Dual terminator D04 = Tin/lead, tube DSL = Tin/lead, tube, single lot date code K A001 G J D04 CHARACTERISTIC RESISTANCE VALUE TOLERANCE SCHEMATIC PACKAGING Note • For additional information on packaging, refer to the Through-Hole Network Packaging document (www.vishay.com/doc?31542). Revision: 12-Sep-13 Document Number: 31516 1 For technical questions, contact: ff2aresistors@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MDM (Military M83401/01 and /02) www.vishay.com Vishay Dale DIMENSIONS in inches (millimeters) 0.310 ± 0.010 (7.87 ± 0.254) TYP 0.030 (0.762) A ± 0.010 (0.254) 0.250 ± 0.005 (6.35 ± 0.127) 0.120 ± 0.005 (3.05 ± 0.127) Pin #1 Identification 0.130 + 0.015 - 0.005 (3.30 + 0.381 - 0.127) Pin #1 0.075 ± 0.015 (1.91 ± 0.381) 0.018 ± 0.003 (0.457 ± 0.076) 0.290 Min. 0.320 Nom. 0.360 Max. (7.37 Min. 8.13 Nom. 9.14 Max.) 0.100 ± 0.010 (2.54 ± 0.254) Non-Accumulative Tol. “C” Spaces B ± 0.010 (0.254) VISHAY DALE MODEL 0.010 + 0.005 - 0.002 (0.254 + 0.127 - 0.051) 0.050 ± 0.005 (1.27 ± 0.127) A B C MDM14 0.750 (19.05) 0.600 (15.24) 6 MDM16 0.850 (21.59) 0.700 (17.78) 7 IMPEDANCE CODES CODE R1 () R2 () CODE R1 () R2 () A001 82 130 A010 330 470 A002 120 200 A011 330 680 A003 130 210 A012 1.5K 3.3K A004 160 260 A013 3K 6.2K A005 180 240 A014 180 270 A006 180 390 A015 270 270 A007 220 270 A016 560 560 A008 220 330 A017 560 1.2K A009 330 390 A018 620 2.7K TECHNICAL SPECIFICATIONS PARAMETER UNIT MDM SERIES Maximum Operating Voltage VDC 100 Voltage Coefficient of Resistance Veff < 50 ppm Dielectric Strength VAC 200 per min  10 000 M Insulation Resistance Operating Temperature Range °C -55 to +125 Storage Temperature Range °C -55 to +150 MECHANICAL SPECIFICATIONS Marking Resistance to Solvents Solderability Body Terminals Revision: 12-Sep-13 Permanency testing per MIL-PRF-83401 Per MIL-PRF-83401 Molded epoxy Copper alloy, hot-solder dipped Document Number: 31516 2 For technical questions, contact: ff2aresistors@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MDM (Military M83401/01 and /02) www.vishay.com Vishay Dale CIRCUIT APPLICATIONS 01 Schematic MDM1401 (M8340101xxxxxxB) MDM1601 (M8340102xxxxxxB) 13 or 15 resistors with one pin common The MDMxx01 provides the user with a choice of 13 or 15 nominally equal resistors, each connected to a common pin. Commonly used in the following applications: • • • • • • • • • MOS/ROM Pull-up/Pull-down  • Open Collector Pull-up • “Wired OR” Pull-up • Power Driven Pull-up MDM1401 Pin #1 MDM1601 03 Schematic • TTL Input Pull-down • Digital Pulse Squaring • TTL Unused Gate Pull-up • High Speed Parallel Pull-up MDM1403 (M8340101xxxxxxA) MDM1603 (M8340102xxxxxxA) 7 or 8 isolated resistors The MDMxx03 provides the user with a choice of 7 or 8 nominally equal resistors, with each resistor isolated from all others. Commonly used in the following applications: • Long-line Impedance Balancing • LED Current Limiting • ECL Output Pull-down • TTL Input Pull-down • “Wired OR” Pull-up • Power Driven Pull-up • Power Gate Pull-up • Line Termination MDM1403 Pin #1 MDM1603 05 Schematic R1 R1 R2 R1 R2 R1 R2 R1 R2 R1 R2 R1 R2 R2 MDM1405 (M8340101xxxxxxJ) MDM1605 (M8340102xxxxxxJ) R1 R1 R1 R2 R2 R2 R2 12 or 14 resistor pairs R1 R1 R1 The MDMxx05 provides the user with a choice of 12 or 14 pairs of R1/R2 resistor values for pulse squaring and TTL dual-line terminating requirements. R1 R2 R2 R2 MDM1405, MDM1605 Pin #1 CAGE CODE: 91637 DERATING MDM 16 1.50 MDM 14 1.30 1.00 05 Schematic Power Rating (W) 03 Schematic Power Rating (W) Power Rating (W) 01 Schematic MDM 16 1.60 MDM 14 1.40 1.00 1.20 MDM 16 MDM 14 1.00 Single Resistor 0.20 Single Resistor 1.40 Single Resistor 0.10 0.05 - 55 + 25 + 70 + 125 + 150 Ambient Temperature °C Revision: 12-Sep-13 - 55 + 25 + 70 + 125 + 150 Ambient Temperature °C - 55 + 25 + 70 + 125 + 150 Ambient Temperature °C Document Number: 31516 3 For technical questions, contact: ff2aresistors@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MDM (Military M83401/01 and /02) www.vishay.com Vishay Dale PERFORMANCE CONDITIONS MAX. R (TYPICAL TEST LOTS) 1.5 x rated power, applied 1.5 h “ON” and 0.5 h “OFF” for 100 h ± 4 h at +25 °C ambient temperature ± 0.50 % R 5 cycles between -65 °C and +125 °C ± 0.50 % R 2.5 x rated working voltage for 5 s ± 0.25 % R (Char. K) ± 0.50 % R (Char. M) 45 min at full rated working voltage at -65 °C ± 0.25 % R (Char. K) ± 0.50 % R (Char. M) 240 h with humidity ranging from 80 % RH to 98 % RH ± 0.50 % R Leads immersed in +260 °C solder to within 1/16" of body for 10 s ± 0.25 % R Total of 18 shocks at 100 g’s ± 0.25 % R Vibration 12 h at maximum of 20 g’s between 10 Hz and 2000 Hz ± 0.25 % R Load Life 1000 h at +70 °C, rated power applied 1.5 h “ON”, 0.5 h “OFF” for full 1000 h period ± 0.50 % R (Char. K) ± 2.00 % R (Char. M) Terminal Strength 4.5 pound pull for 30 s ± 0.25 % R Insulation Resistance 10 000 M (minimum) - No evidence of arcing or damage (200 VRMS for 1 min) - TEST Power Conditioning Thermal Shock Short Time Overload Low Temperature Operation Moisture Resistance Resistance to Soldering Heat Shock Dielectric Withstanding Voltage Revision: 12-Sep-13 Document Number: 31516 4 For technical questions, contact: ff2aresistors@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000