MBRS130LTR

Bulletin PD-20588 rev. D 03/03 MBRS130LTR SCHOTTKY RECTIFIER 1 Amp SMB Description/ Features Major Ratings and Characteristics Characteristics MBRS130LTR Units IF(AV) Rectangular waveform 1.0 A VRRM 30 V IFSM @ tp= 5 µs sine 230 A VF @ 1.0Apk, TJ= 125°C 0.30 V TJ range - 55 to 125 °C The MBRS130LTR surface-mount Schottky rectifier has been designed for applications requiring low forward drop and small foot prints on PC boards. Typical applications are in disk drives, switching power supplies, converters, free-wheeling diodes, battery charging, and reverse battery protection. Small foot print, surface mountable Very low forward voltage drop High frequency operation Guard ring for enhanced ruggedness and long term reliability CATHODE Device Marking: IR13L 2.15 (.085) 1.80 (.071) 3.80 (.150) 3.30 (.130) 1 1 POLARITY 4.70 (.185) ANODE 2 2 PART NUMBER 4.10 (.161) 2.5 TYP. (.098 TYP.) SOLDERING PAD 2.40 (.094) 1.90 (.075) 1.30 (.051) 0.76 (.030) 0.30 (.012) 0.15 (.006) 5.60 (.220) 5.00 (.197) 2.0 TYP. (.079 TYP.) 4.2 (.165) 4.0 (.157) Outline SMB Dimensions in millimeters and (inches) For recommended footprint and soldering techniques refer to application note #AN-994 www.irf.com 1 MBRS130LTR Bulletin PD-20588 rev. D 03/03 Voltage Ratings Part number VR MBRS130LTR Max. DC Reverse Voltage (V) 30 VRWM Max. Working Peak Reverse Voltage (V) Absolute Maximum Ratings Parameters Value Units Conditions IF(AV) Max. Average Forward Current 1.0 A 50% duty cycle @ TL = 106 °C, rectangular wave form IFSM Max. Peak One Cycle Non-Repetitive 230 A 5µs Sine or 3µs Rect. pulse Surge Current 40 EAS Non- Repetitive Avalanche Energy 3.0 mJ IAR Repetitive Avalanche Current 1.0 A Value Units 0.420 V @ 1A 0.470 V @ 2A 0.300 V @ 1A 0.370 V @ 2A 10ms Sine or 6ms Rect. pulse Following any rated load condition and with rated VRRM applied TJ = 25 °C, IAS = 1A, L = 6mH Current decaying linearly to zero in 1 µsec Frequency limited by TJ max. Va = 1.5 x Vr typical Electrical Specifications Parameters VFM Max. Forward Voltage Drop (1) Conditions TJ = 25 °C TJ = 125 °C 1 mA TJ = IRM Max. Reverse Leakage Current (1) 10 mA TJ = 100 °C 20 mA TJ = 125 °C CT Max. Junction Capacitance 200 pF VR = 5VDC (test signal range 100KHz to 1Mhz) 25°C LS Typical Series Inductance 2.0 nH Measured lead to lead 5mm from package body 10000 V/µs dv/dt Max. Voltage Rate of Change 25 °C VR = rated VR (Rated VR) (1) Pulse Width < 300µs, Duty Cycle < 2% Thermal-Mechanical Specifications Parameters Value TJ Max. Junction Temperature Range(*) - 55 to 125 Tstg Max. Storage Temperature Range RthJL Max. Thermal Resistance Junction to Lead RthJA Max. Thermal Resistance Junction to Ambient wt Approximate Weight - 55 to 150 Conditions °C °C 25 °C/W DC operation (See Fig. 4) 80 °C/W DC operation (**) 0.10 (0.003) g (oz.) Case Style SMB Device Marking IR13L (*) dPtot Units Similar to DO-214AA 1 < thermal runaway condition for a diode on its own heatsink dTj Rth( j-a) (**) Mounted 1 inch square PCB 2 www.irf.com MBRS130LTR Bulletin PD-20588 rev. D 03/03 10 TJ = 125°C 1 100°C 75°C 0.1 50°C 0.01 25°C 0.001 0.0001 0 10 20 30 TJ = 125°C Reverse Voltage - VR (V) TJ = 25°C Fig. 2 - Typical Peak Reverse Current Vs. Reverse Voltage 1 1000 0.1 0 0.2 0.4 0.6 0.8 Forward Voltage Drop - VFM (V) Fig. 1 - Maximum Forward Voltage Drop Characteristics Junc tion Capa citance - C T (pF) Instantaneous Forward Current - IF (A) Reverse Current - IR (mA) 10 TJ = 25°C 100 10 0 10 20 30 Reverse Voltage - VR (V) Fig. 3 - Typical Junction Capacitance Vs. Reverse Voltage www.irf.com 3 MBRS130LTR Bulletin PD-20588 rev. D 03/03 0.5 120 Average Power Loss - (Watts) Allowable Lead Temperature (°C) 130 DC D = 0.20 D = 0.25 D = 0.33 D = 0.50 D = 0.75 110 100 Square wave (D = 0.50) 80% Rated Vr applied D = 0.20 D = 0.25 D = 0.33 D = 0.50 D = 0.75 0.4 0.3 DC RMSLimit 0.2 0.1 see note (2) 0 90 0 0.4 0.8 1.2 0 1.6 1.2 1.6 1000 At Any Rated Load Condition And With Rated Vrrm Applied Following Surge FSM (A) 0.8 Fig. 5 - Maximum Average Forward Dissipation Vs. Average Forward Current Fig. 4 - Maximum Average Forward Current Vs. Allowable Lead Temperature Non-repetitive Surge Current - I 0.4 Average Forward Current - I F(AV) (A) Average Forward Current - I F(AV) (A) 100 10 10 100 1000 10000 Square Wave Pulse Duration - t p (microsec) Fig. 6 - Maximum Peak Surge Forward Current Vs. Pulse Duration (2) Formula used: TC = TJ - (Pd + PdREV) x RthJC ; Pd = Forward Power Loss = IF(AV) x VFM @ (IF(AV) / D) (see Fig. 6); PdREV = Inverse Power Loss = VR1 x IR (1 - D); IR @ VR1 = 80% rated VR 4 www.irf.com MBRS130LTR Bulletin PD-20588 rev. D 03/03 Tape & Reel Information Dimensions in millimetres and (inches) Marking & Identification Each device has 2 rows for identification. The first row designates the device as manufactured by International Rectifier as indicated by the letters "IR", and the Part Number (indicates the current and the voltage rating). The second row indicates the year, the week of manufacturing and the Site ID. Ordering Information MBRS130LTR - TAPE AND REEL WHEN ORDERING, INDICATE THE PART NUMBER AND THE QUANTITY ( IN MULTIPLES OF 3000 PIECES). EXAMPLE: MBRS130LTR - 6000 PIECES IR13L VOLTAGE CURRENT IR LOGO YYWWX SITE ID WEEK YEAR www.irf.com 5 MBRS130LTR Bulletin PD-20588 rev. D 03/03 Data and specifications subject to change without notice. This product has been designed and qualified for Industrial Level. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 03/03 6 www.irf.com