O096O064ABPP3N0000

Vishay Dale Electronics, Inc. Information Display Products OLED Product Data Sheet OLED SPECIFICATION Model No: OLED-096O064A-BPP3N00000 SPECIFICATION Module # : Global SAP # : Version: B OLED-096O064A-BPP3N00000 O096O064ABPP3N0000 APPROVED BY: ( FOR CUSTOMER USE ONLY ) SALES BY RELEASE DATE: APPROVED BY CHECKED BY PREPARED BY MODEL NO：OLED-096O064A-BPP3N00000 RECORDS OF REVISION VERSION DATE DOC. FIRST ISSUE REVISED SUMMARY PAGE NO. 0 2013/09/12 First release A 2014/06/12 Add Low Temperature storage. B 2014/12/08 Modified VCC,ICC ,Brightness & the height of module. OLED-096O064A-BPP3N00000 Contents 1.Module Classification Information 2.General Specification 3.Contour Drawing & Block Diagram 4.Interface Pin Function 5.Absolute Maximum Ratings 6.Electrical Characteristics 7.Optical Characteristics 8.OLED Lifetime 9.Reliability 10.Inspection Specification 11.Precautions in Use of OLED Modules OLED-096O064A-BPP3N00000 1.Module Classification Information OLED -096 O 064 A B 1 2 3 4 5 6 P P 3 N 0 7 10 11 12 8 9 0 000 13 1 Brand：Vishay Intertechnology, Inc. 2 Horizontal Format: 3 Display Type：N→Character Type, H→Graphic Type, Y→TAB Type ,O→COG Type 4 5 Vertical Format: 64 rows or lines Series code: A A：Amber 6 Emitting Color 96 columns B：Blue C：Full color G：Green W：White Y：Yellow Green L：Yellow P：With Polarizer; N: Without Polarizer 7 Polarizer 8 Display 9 10 Driver Voltage Touch Panel Mode P：Passive Matrix ; A: Active Matrix 3: 3.0 V; 5: 5.0V N：Without touch panel; T: With touch panel 0：Standard type 1. Sunlight Readable type 11 Products type 2. Transparent OLED (TOLED) 3. Flexible OLED 4. OLED for Lighting 0：Standard(A-level) 2：B-level 12 Product grades 3：C-level 4：high class(AA-level) 5：Customer offerings 13 R：RED Serial No. Application serial number(000~ZZZ) OLED-096O064A-BPP3N00000 2.General Specification 2.1. Item Dimension Unit 96 x 64 Dots － 24.9 × 22.95 × 1.65 (mm) mm 19.946 × 13.418 (mm) mm Pixel Size 0.186 × 0.188 (mm) mm Pixel Pitch 0.208 × 0.21 (mm) mm Dot Matrix Module dimension Active Area Display Mode Passive Matrix Display Color Blue Drive Duty IC 1/64 Duty SSD1305Z OLED-096O064A-BPP3N00000 1.65±0.3 10.0 5.0 96*64 Pixels Remove Tape T=0.15mm Max 0.70 0.70 8.0 2.1035 0.50±0.5 0.50±0.5 1.474 2.477 15.424(VA) 13.418(AA) 16.9(Polarizer) 17.9±0.2 (Cap Size) 22.95±0.2 (Panel Size) 24.9±0.2 (Panel Size) 24.9±0.2 (Cap Size) 23.9(Polarizer) 21.953(VA) 19.946(AA) Polarizer T=0.25mm Shading tape 4.1±0.2 2 -R 1 0 NC(GND) VCC VSS VDD VDDIO BS1 BS2 CS# RES# D/C# R/W# E/RD# D0 D1 D2 D3 D4 D5 D6 D7 IREF VCOMH VCC VLSS NC(GND) Contact side Segment 113 (Column 1) Common 32 (Row 63) Common 63 (Row 1) The non-specified tolerance of dimension is 0.208 0.186 14 15 16 17 18 19 20 21 22 23 24 25 Glue 0.16±0.03 SCALE 20/1 OLED-096O064A-BPP3N00000 0± 1 2 3 4 5 6 7 8 9 10 11 12 13 .0 5 Contact side 0.32 15.0±0.1 (Alignment Hole) P0.65*24=15.6 16.8±0.2 0.188 4.05 0 .4 25 0.21 1.50±0.3 5.0±0.2 9.8±0.3 32.75 1.10 3. Contour Drawing & Block Diagram Segment 18 (Column 96) Common 0 (Row 64) Common 31 (Row 2) 0.3mm. VCC Supplied Externally *For more information, please refer to the SSD1305 datasheet. OLED-096O064A-BPP3N00000 4. Interface Pin Function Pin Number Symbol 1. N.C. (GND) - 2. VCC P 3. VSS P 4. VDD P 5. VDDIO P BS1 BS2 I 8. CS# I 9. RES# I 10. D/C# I 11. R/W# I 12. E/RD# I 6. 7. I/O Function Reserved Pin(Supporting Pin) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground. Power Supply for OLED Panel This is the most positive voltage supply pin of the chip.It must be supplied externally. Ground of Logic Circuit This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground. Power Supply for Logic Circuit This is a voltage supply pin. It must be connected to external source. Power supply for interface logic level. It should be match with MCU interface voltage level. VDDIO must always be equal or lower than VDD. Communicating Protocol Select These pins are MCU interface selection input. See the following table: 68XX-parallel 80XX-parallel Serial I2C BS1 0 1 0 1 BS2 1 1 0 0 Chip Select This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low. Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. Data/ Command Control This pin is Data/Command control pin. When the pin is pulled high, the input at D7~D0 is treated as display data. When the pin is pulled low, the input at D7~D0 will be transferred to the command register. For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams. When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection. Read/ Write Selector Write This pin is MCU interface input. When interfacing to a68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XXinterface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. Read/Write Enable or Read OLED-096O064A-BPP3N00000 This pin is MCU interface input. When interfacing to a68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low. When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low. 13. 14. 15. 16. 17. 18. 19. 20. D0~D7 Host Data In put/ Output Bus These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the I/O serial data input SDIN and D0 will be the serial clock input SCLK. When I2Cmode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL. 21. IREF I 22. VCOMH O 23. VCC P 24. VLSS P 25. N.C. (GND) - Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10μA. Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. Power Supply for OLED Panel This is the most positive voltage supply pin of the chip.It must be supplied externally. Ground of Analog Circuit This is an analog ground pin. It should be connected to VSS externally. Reserved Pin(Supporting Pin) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground. OLED-096O064A-BPP3N00000 5.Absolute Maximum Ratings Parameter Symbol Min Max Unit Notes Supply Voltage for Logic VDD -0.3 4 V 1, 2 Supply Voltage for Display VCC 0 15 V 1, 2 Operating Temperature TOP -40 +80 °C - TSTG -40 +80 °C - Storage Temperature Note 1: All the above voltages are on the basis of “VSS = 0V”. Note 2: When this module is used beyond the above absolute maximum ratings, permanent breakage of the module may occur. Also, for normal operations, it is desirable to use this module under the conditions according to Section 6 ‘’Electrical Characteristics’’. If this module is used beyond these conditions, malfunctioning of the module can occur and the reliability of the module may deteriorate OLED-096O064A-BPP3N00000 6.Electrical Characteristics Item Symbol Condition Min Typ Max Unit Supply Voltage for Logic VDD － 2.8 3.0 3.3 V Supply Voltage for Display VCC － 10 12 14 V Input High Volt. VIH － 0.8×VDD － VDDIO V Input Low Volt. VIL － 0 － 0.2×VDD V Output High Volt. VOH － 0.9×VDD － VDDIO V Output Low Volt. VOL － 0 － 0.1×VDD V 50% Check Board operating Current ICC VCC=12V 7 8 10 mA OLED-096O064A-BPP3N00000 7.Optical Characteristics Item View Angle Contrast Ratio Response Time Symbol Condition Min Typ Max Unit (V)θ 160 deg (H)φ 160 deg CR Dark T rise － 10 μs T fall － 10 μs 60 80 cd/m2 Display with 50% check Board Brightness 2000:1 － CIEx(Blue) (CIE1931) 0.12 0.16 0.20 CIEy(Blue) (CIE1931) 0.19 0.23 0.27 OLED-096O064A-BPP3N00000 － 8.OLED Lifetime ITEM Conditions Operating Life Time Ta=25℃ / Initial 50% check board brightness Typical Value Min Typ 40,000 Hrs 50,000 Hrs Remark Note Notes: 1. Life time is defined the amount of time when the luminance has decayed to 50% of initial value. 4. Current consumption: within ± 50% of initial value. APPENDIX: RESIDUE IMAGE Because the pixels are lighted in different time, the luminance of active pixels may reduce or differ from inactive pixels. Therefore, the residue image will occur. To avoid the residue image, every pixel needs to be lighted up uniformly. OLED-096O064A-BPP3N00000 10.Inspection Specification NO 01 02 03 04 Item Electrical Testing Black or white spots on OLED (display only) OLED black spots, white spots, contamina tion (non-displ ay) Polarizer bubbles Criterion 1.1 Missing vertical, horizontal segment, segment contrast defect. 1.2 Missing character, dot or icon. 1.3 Display malfunction. 1.4 No function or no display. 1.5 Current consumption exceeds product specifications. 1.6 OLED viewing angle defect. 1.7 Mixed product types. 1.8 Contrast defect. 2.1 White and black spots on display ≦0.25mm, no more than three white or black spots present. 2.2 Densely spaced: No more than two spots or lines within 3mm. 3.1 Round type : As following drawing Φ=( x + y ) / 2 SIZE Acceptable Q TY Accept no dense 2 Φ≦0.10 0.10＜ Φ≦0.20 0.20＜ Φ≦0.25 0.25＜Φ 3.2 Line type : (As following drawing) Length Width --W≦0.02 L≦3.0 0.02＜W≦0.03 L≦2.5 0.03＜W≦0.05 --0.05＜W If bubbles are visible, judge using black spot specifications, not easy to find, must check in specify direction. Size Φ Φ≦0.20 0.20＜Φ≦0.50 0.50＜Φ≦1.00 1.00＜Φ Total Q TY OLED-096O064A-BPP3N00000 AQL 0.65 2.5 2.5 1 0 Acceptable Q TY Accept no dense 2 2.5 As round type Acceptable Q TY Accept no dense 3 2 0 3 2.5 NO 05 Item Scratches Criterion Follow NO.3 OLED black spots, white spots, contamination Symbols Define: x: Chip length y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: OLED side length L: Electrode pad length: AQL 6.1 General glass chip : 6.1.1 Chip on panel surface and crack between panels: 06 Chipped glass z: Chip thickness Z≦1/2t y: Chip width x: Chip length Not over viewing x≦1/8a area Not exceed 1/3k 1/2t＜z≦2t x≦1/8a ☉If there are 2 or more chips, x is total length of each chip. 6.1.2 Corner crack: z: Chip thickness Z≦1/2t y: Chip width x: Chip length Not over viewing x≦1/8a area Not exceed 1/3k 1/2t＜z≦2t x≦1/8a ☉If there are 2 or more chips, x is the total length of each chip. OLED-096O064A-BPP3N00000 2.5 NO Item Criterion Symbols : x: Chip length y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: OLED side length L: Electrode pad length 6.2 Protrusion over terminal : 6.2.1 Chip on electrode pad : y: Chip width x: Chip length y≦0.5mm x≦1/8a 6.2.2 Non-conductive portion: 06 AQL z: Chip thickness 0 ＜ z≦t Glass crack 2.5 y: Chip width x: Chip length z: Chip thickness y≦ L x≦1/8a 0 ＜ z≦t ☉If the chipped area touches the ITO terminal, over 2/3 of the ITO must remain and be inspected according to electrode terminal specifications. ☉If the product will be heat sealed by the customer, the alignment mark not be damaged. 6.2.3 Substrate protuberance and internal crack. y: width y≦1/3L OLED-096O064A-BPP3N00000 x: length x≦a NO 07 08 09 10 11 Item Cracked glass Backlight elements Criterion AQL The OLED with extensive crack is not acceptable. 2.5 8.1 Illumination source flickers when lit. 8.2 Spots or scratched that appear when lit must be judged. Using OLED spot, lines and contamination standards. 8.3 Backlight doesn’t light or color wrong. 0.65 2.5 0.65 Bezel 9.1 Bezel may not have rust, be deformed or have fingerprints, stains or other contamination. 9.2 Bezel must comply with job specifications. 2.5 PCB、COB 10.1 COB seal may not have pinholes larger than 0.2mm or contamination. 10.2 COB seal surface may not have pinholes through to the IC. 10.3 The height of the COB should not exceed the height indicated in the assembly diagram. 10.4 There may not be more than 2mm of sealant outside the seal area on the PCB. And there should be no more than three places. 10.5 No oxidation or contamination PCB terminals. 10.6 Parts on PCB must be the same as on the production characteristic chart. There should be no wrong parts, missing parts or excess parts. 10.7 The jumper on the PCB should conform to the product characteristic chart. 10.8 If solder gets on bezel tab pads, OLED pad, zebra pad or screw hold pad, make sure it is smoothed down. 11.1 No un-melted solder paste may be present on the PCB. 11.2 No cold solder joints, missing solder connections, oxidation or icicle. 11.3 No residue or solder balls on PCB. 11.4 No short circuits in components on PCB. 2.5 2.5 Soldering OLED-096O064A-BPP3N00000 2.5 0.65 2.5 0.65 2.5 2.5 0.65 0.65 2.5 2.5 0.65 NO 12 Item Criterion AQL 2.5 General appearance 12.1 No oxidation, contamination, curves or, bends on interface Pin (OLB) of TCP. 12.2 No cracks on interface pin (OLB) of TCP. 12.3 No contamination, solder residue or solder balls on product. 12.4 The IC on the TCP may not be damaged, circuits. 12.5 The uppermost edge of the protective strip on the interface pin must be present or look as if it cause the interface pin to sever. 12.6 The residual rosin or tin oil of soldering (component or chip component) is not burned into brown or black color. 12.7 Sealant on top of the ITO circuit has not hardened. 12.8 Pin type must match type in specification sheet. 12.9 OLED pin loose or missing pins. 12.10 Product packaging must the same as specified on packaging specification sheet. 12.11 Product dimension and structure must conform to product specification sheet. OLED-096O064A-BPP3N00000 0.65 2.5 2.5 2.5 2.5 2.5 0.65 0.65 0.65 0.65 Check Item Classification No Display Major Missing Line Major Pixel Short Major Darker Short Major Wrong Display Major Un-uniform B/A x 100% < 70% A/C x 100% < 70% Major Criteria OLED-096O064A-BPP3N00000 11.Precautions in Use of OLED Modules Modules (1)Avoid applying excessive shocks to module or making any alterations or modifications to it. (2)Don’t make extra holes on the printed circuit board, modify its shape or change the components of OLED display module. (3)Don’t disassemble the OLED display module. (4)Don’t operate it above the absolute maximum rating. (5)Don’t drop, bend or twist OLED display module. (6)Soldering: only to the I/O terminals. (7)Storage: please store in anti-static electricity container and clean environment. (8)Use a "Screen Saver" to extend the lifetime. Do not show fixed information for a long time in the application. (9)Don't use fixed information in OLED panel for long time that will cause "screen burn" effect. (10)The manufacturer has the right to change the passive components, including R2and R3 adjust resistors. (Resistors, capacitors and other passive components will have different appearance and color caused by the different supplier.) (11)The manufacturer has the right to change the PCB Rev. (In order to satisfy supply stability, management optimization, and the best product performance..., under the premise of not affecting the electrical characteristics and external dimensions. The manufacturer has the right to modify the version.) 11.1. Handling Precautions (1) Since the display panel is made of glass, do not apply mechanical impacts such us dropping from a high position. (2) If the display panel is broken by some accident and the internal organic substance leaks out, be careful not to inhale or ingest the organic substance. (3) If pressure is applied to the display surface or its neighborhood of the OLED display module, the cell structure may be damaged, be careful not to apply pressure to these sections. (4) The polarizer covering the surface of the OLED display module is soft and easily scratched. Please be careful when handling the OLED display module. (5) When the surface of the polarizer of the OLED display module has soil, clean the surface. It takes advantage of by using following adhesion tape. * Scotch Mending Tape No. 810 or an equivalent Never try to breathe upon the soiled surface or wipe the surface using cloth containing solvent such as ethyl alcohol, since the surface of the polarizer will become cloudy. Also, pay attention that the following liquid and solvents can damage the polarizer: * Water * Ketone * Aromatic Solvents (6) Hold OLED display module very carefully when placing OLED display module into the system housing. Do not apply excessive stress or pressure to OLED display module. And, do not over bend the film with electrode pattern layouts. These stresses will influence the display performance. Also, secure sufficient rigidity for the outer cases. OLED-096O064A-BPP3N00000 (7) Do not apply stress to the LSI chips and the surrounding molded sections. (8) Do not disassemble or modify the OLED display module. (9) Do not apply input signals while the logic power is off. (10) Pay sufficient attention to the working environments when handing OLED display modules to prevent occurrence of element breakage accidents by static electricity. * Be sure to make human body grounding when handling OLED display modules. * Be sure to ground tools to use or assembly such as soldering irons. * To suppress generation of static electricity, avoid carrying out assembly work under dry environments. * Protective film is being applied to the surface of the display panel of the OLED display module. Be careful since static electricity may be generated when removing the protective film. (11) Protective film is applied to the surface of the display panel. Remove the protective film before assembly. If the OLED display module has been stored for a long period of time, residue adhesive material from the protective film may remain on the surface of the display panel after the film is removed. In such case, remove the residue material by the method introduced in the above Section 5. (12) If electric current is applied when the OLED display module has moisture condensation or when it is placed under high humidity environments, the electrodes may corrode. 11.2. Storage Precautions (1) When storing OLED display modules, put them in static electricity preventive bags avoiding exposure to direct sun light and fluorescent lamps. Avoid high temperature and high humidity environment or low temperature (less than 0°C) environments. (We recommend storing these modules in the packaged state as they were shipped.) At that time, be careful not to let water drops adhere to the packages or bags or let condensation occur with them. (2) If electric current is applied when condensation is present or when it is placed under high humidity environments, the electrodes may corrode. 11.3. Designing Precautions (1) The absolute maximum ratings are the ratings which cannot be exceeded for OLED display module, and if these values are exceeded, panel damage may be happen. (2) To prevent occurrence of malfunctioning by noise, pay attention to satisfy the VIL and VIH specifications and, at the same time, to make the signal line cable as short as possible. (3) We recommend you to install excess current preventive unit (fuses, etc.) to the power circuit (VDD). (Recommend value: 0.5A) (4) Pay sufficient attention to avoid occurrence of mutual noise interference with the neighboring devices. (5) For EMI, take necessary measures in the application equipment. (6) When fastening the OLED display module, fasten the external plastic housing section. (7) If power supply to the OLED display module is forcibly shut down by such errors as taking out the main battery while the OLED display panel is in operation, we cannot guarantee the quality of this OLED display module. OLED-096O064A-BPP3N00000 * Connection (contact) to any other potential than the above may lead to rupture of the IC.11.4. Precautions when disposing of the OLED display modules 1) Request the qualified companies to handle industrial wastes when disposing of the OLED display modules. Or, when burning them, be sure to observe the environmental and hygienic laws and regulations. 11.5. Other Precautions (1) When an OLED display module is operated for a long time with a fixed pattern, the pattern may remain as an after image with slight contrast or brightness variation. Nonetheless, if the operation is interrupted and left unused for a while, normal state can be restored. Also, there will be no problem in the reliability of the module. (2) To protect OLED display modules from performance drops by static electricity rapture, etc., do not touch the following sections whenever possible while handling the OLED display modules. * Pins and electrodes * Pattern layouts such as the TCP & FPC (3) With this OLED display module, the OLED driver is exposed. Generally, semiconductor elements change their characteristics when exposed to light, similar to the principle of the solar battery. Consequently, if this OLED driver is exposed to light, malfunctioning may occur. * Design the product and installation method so that the OLED driver may be shielded from light in actual usage. * Design the product and installation method so that the OLED driver may be shielded from light during the inspection processes. (4) Although this OLED display module stores the operational state data by the commands and the indication data, when excessive external noise, etc. enters into the module, the internal states may be changed. It therefore is necessary to take appropriate measures to suppress noise generation or to protect from influences of noise on the system design. (5) We recommend you to construct its software to make periodical refreshment of the operation statuses (re-setting of the commands and re-transference of the display data) to cope with catastrophic noise. (6)Resistors, capacitors and other passive components will have different appearance and color caused by the different supplier. (7)The manufacturer has the right to upgrade and modify the product function. OLED-096O064A-BPP3N00000 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Vishay: O096O064ABPP3N0000 O128O064BGPP3N0000 O128O064BLPP3N0000 O128O064BWPP3N0000 O128O064BBPP3N0000