PE30
www.vishay.com
Vishay Sfernice
Fully Sealed Potentiometer Professional Grade
FEATURES
• High power rating 3 W at 70 °C
• Low temperature coefficient
(150 ppm/°C typical)
• Cermet element
• Full sealing
LINK TO ADDITIONAL RESOURCES
• Use of faston 2.86 connections
3D 3D
3D Models
• Tests according to CECC 41000 or IEC 60393-1
Capabilities and
Custom Options
• Wires and connectors available
QUICK REFERENCE DATA
• Custom design on request
Multiple module
Switch module
Detent module
• Center detent option
No
n/a
Yes
A: linear, L: logarithmic,
F: reverse logarithmic
IP 67
25K cycles
Special electrical laws
Sealing level
Lifespan
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
DIMENSIONS in millimeters (inches) ± 0.5 mm (± 0.02")
PE30L
8
(0.31)
20 (0.79) max.
12 (0.47)
76°
14 wrench
13 (0.51)
max.
Thread M10 x 0.75
Ø6
(0.24)
0.5
(0.02)
FG = 16 (0.63)
Ø 19.7
(0.78)
FL = 25 (0.99)
c
R 5.2
(0.20)
3
(0.12)
b
2.85 (0.11)
0.8
(0.3)
12.5
(0.49)
9.2
(0.36)
8.8
(0.35)
Ø 3.5
(0.14)
PANEL MOUNT
FR = 50 (1.97)
3
(0.12)
Ø 1.8 (0.07)
PE30LL: LPRP - Locating Peg
Ø 10.5
(0.41)
a
3
(0.12)
2.3
(0.9)
23 (0.91) max.
PE30ME: Panel Sealed
16 (0.63) max.
Sealing ring
0.7 (0.03)
Ø 1.2
(0.05)
Ø 1 (0.4)
Flats
located
8 ± 0.2
(0.31 ± 0.01)
Ø 10.5
(0.41)
Revision: 25-Jul-2022
Ø6
(0.24)
Ø 19.7
(0.78)
9 (0.35)
FD = 13
(0.61)
PANEL MOUNT
Slot
1 x 1.8
deep
FJ = 22 (0.87)
FP = 47 (1.85)
Document Number: 51037
1
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PE30
www.vishay.com
Vishay Sfernice
ELECTRICAL SPECIFICATIONS
Resistive element
Cermet
Electrical travel
Resistance range
270° ± 10°
22 Ω to 10 MΩ
Linear taper
100 Ω to 2.2 MΩ
Logarithmic taper
Standard series E3
Tolerance
1 - 2.2 - 4.7 and on request 1 - 2 - 5
Standard
± 20 %
On request
± 10 % to ± 5 %
Axis Title
10000
100
Taper
F
1000
60
1st line
2nd line
2nd line
Total Resistance (%)
80
A
L
40
100
20
10
0
0
20
40
60
80
100
Clockwise Shaft Rotation (%)
Axis Title
10000
Linear taper “A”
3
Linear
Logarithmic
3 W at 70 °C
1.5 W at 70 °C
1st line
2nd line
Power rating
2nd line
Power (W)
1000
2
Logarithmic taper “L and F”
100
1
10
0
0
20
40
60 70 80
100
120
140
Ambient Temperature (°C)
Circuit diagram
a
c
(1)
(3)
cw
b
(2)
Temperature coefficient (typical)
Limiting element voltage
Contact resistance variation (typical)
End resistance (typical)
± 150 ppm/°C
300 V
3 % Rn or 3 Ω
1Ω
Dielectric strength (RMS)
2500 V
Insulation resistance (300 VDC)
105 MΩ
Independent linearity (typical)
±5%
Revision: 25-Jul-2022
Document Number: 51037
2
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PE30
www.vishay.com
Vishay Sfernice
STANDARD RESISTANCE ELEMENT DATA
STANDARD
RESISTANCE
VALUES
Ω
22
47
100
220
470
1K
2.2K
4.7K
10K
22K
47K
100K
220K
470K
1M
2.2M
4.7M
10M
MAX. POWER
AT 70 °C
W
3
3
3
3
3
3
3
3
3
3
1.91
0.90
0.41
0.19
0.09
0.04
0.02
0.01
LINEAR TAPER
MAX. WORKING
MAX. CUR.
VOLTAGE
THROUGH WIPER
V
mA
8.1
369
11.9
252
17.3
173
25.7
116
37.5
79
54.8
54
81.2
37
118.7
25
173.2
17
256.9
11
299.6
6.3
300.0
3
300.0
1.36
298.8
0.63
300.0
0.3
296.6
0.13
300.0
0.06
300.0
0.03
MAX. POWER
AT 70 °C
W
LOGS TAPER
MAX. WORKING
VOLTAGE
V
MAX. CUR.
THROUGH WIPER
mA
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
0.9
0.41
0.19
0.09
0.04
12.2
18.2
26.6
38.7
57.4
83.9
122
181.6
265
300
300
300
300
300
122
82.6
56.6
38.7
26.1
17.9
12.2
8.25
5.64
3
1.36
0.63
0.30
0.13
MECHANICAL SPECIFICATIONS
Mechanical travel
Operating torque / typical value
End stop torque
Tightening torque of mounting nut
Unit weight
Terminals
300° ± 5°
3 Ncm
120 Ncm max.
250 Ncm max.
23 g to 32 g max.
4.25 oz.-inch
10.51 lb oz.-inch max.
22 lb-inch max.
0.8 oz. to 1.13 oz.
e3: pure Sn
ENVIRONMENTAL SPECIFICATIONS
Temperature range
Climatic category
Sealing
-55 °C to +125 °C
55/125/56
Fully sealed - container IP67
OPTIONS
Special feature command shaft
Panel sealing (PE30M)
Locating peg (PE30LL)
Length is measured from the mounting surface to the free end of the shaft. The screwdriver
slot is aligned with the wiper within ± 10°. Special shafts are available, in accordance to
drawings supplied by customers. We recommend that customers should not machine tool
shafts, in order to avoid damage. Bending or torsion of terminals should also be avoided.
The panel sealing device consists of a ring located in a groove on the potentiometer face.
Sealing is obtained by tightening the ring against the panel when mounting the
potentiometer.
Old code: PE30P
Location is obtained by fitting a special washer on the mounting face of the potentiometer.
Old code: LPRP
The shaft locking device consists of a tapered nut tightening a slotted notched washer
against both bushing and shaft.
DBAN tightening torque is 200 Ncm, shaft locking torque being 30 Ncm.
DBAN is also available with all special types.
This device is normally supplied in a separate bag. Can be pre-mounted on request.
1)
Shaft locking (PE30LD)
2)
14 wrench
12 wrench
Assembling
method
6.5
15
Revision: 25-Jul-2022
Document Number: 51037
3
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PE30
www.vishay.com
Vishay Sfernice
CENTER DETENT
• Stable position in mid mechanical travel
• Output ratio 50 % ± 10 %
• Rotational life: 10 000 actuations
Full CCW
Full CW
ORDERING INFORMATION (First order only)
CV1M
MARKING
• Vishay trademark
• Full ordering information (see Ordering Information table)
• Manufacturing date code
• Marking of terminals 3, and a, b, c
PERFORMANCE
TYPICAL VALUES AND DRIFTS
TESTS
CONDITIONS
ΔRT/RT (%)
ΔR1-2/R1-2 (%)
OTHER
Electrical endurance
1000 h at rated power
90'/30' - ambient temp. 70 °C
±1%
-
Contact res. variation: < 3 % Rn
Climatic sequence
Phase A dry heat 125 °C
Phase B damp heat
Phase C cold -55 °C
Phase D damp heat 5 cycles
± 0.5 %
±1%
-
Damp heat, steady state
56 days
40 °C 93 % HR
± 0.5 %
±1%
Insulation resistance: > 104 MΩ
Change of temperature
5 cycles
-55 °C at +125 °C
± 0.5 %
-
-
Mechanical endurance
Shock
Vibration
25 000 cycles
±3%
-
Contact res. variation: < 2 % Rn
50 g’s at 11 ms
3 successive shocks
in 3 directions
± 0.1 %
± 0.2 %
-
10 Hz to 55 Hz
0.75 mm or 10 g’s
during 6 h
± 0.1 %
± 0.2 %
-
Note
• Nothing stated herein shall be construed as a guarantee of quality or durability
Revision: 25-Jul-2022
Document Number: 51037
4
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PE30
www.vishay.com
Vishay Sfernice
ORDERING INFORMATION (part number)
P
E
3
MODEL BUSHING
PE30
0
L
OPTION
B
F
G
2
0
OHMIC
VALUE
SHAFT
A law =
For L bushing (= old codes:)
from 22 Ω
FG 16 mm, slotted = AC
to 10 MΩ
FL 25 mm, slotted = AM
For L bushing
FR 50 mm, plain = AL
D = DBAN
M = panel
L and F
L = LPRP
sealed
laws =
For M bushing
B = DBAN
M10 x 0.75
FD = 13 mm, slotted = AC from 100 Ω
and LPRP
to 2.2 MΩ
FJ = 22 mm, slotted = AM
FP = 47 mm, plain = AL
For M bushing
E = peg
A = peg
and DBAN
0 = none
L=
M10 x 0.75
4
M
A
B
TOLERANCE
TAPER
PACKAGING
M = ± 20 %
On request:
K = ± 10 %
J=±5%
A = linear
L = clockwise
logarithmic
F = clockwise
inverse
logarithmic
B = box of
10 pieces
SPECIAL
NUMBER
(if applicable)
Given by
Vishay
for custom
design
or
E105
CV1M
PART NUMBER DESCRIPTION (for information only)
PE30
LPRP
AC
200K 20 %
A
DBAN
CV1M
BO
MODEL FEATURES OPTION SHAFT VALUE TOL. TAPER OPTION SPECIAL DETENT PACKAGING
e3
CUSTOM
LEAD
SPECIAL
SHAFT
(Pb)-FREE
RELATED DOCUMENTS
APPLICATION NOTES
Potentiometers and Trimmers
www.vishay.com/doc?51001
Guidelines for Vishay Sfernice Resistive and Inductive Components
www.vishay.com/doc?52029
Capabilities and Custom Options
www.vishay.com/doc?48485
Revision: 25-Jul-2022
Document Number: 51037
5
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 01-Jan-2022
1
Document Number: 91000
