PR02FS0202708KR500

PR02-FS www.vishay.com Vishay BCcomponents High Pulse, Fusible, Non-Inductive, Flameproof, Metal Film Leaded Resistor FEATURES • UL 1412, Ed.5 US safety standard recognized; UL file no. E362452 • CAN/CSA C22.2 No.60065 Ed.2 Canadian safety standard recognized; UL file no. E362452 • Defined fusing characteristics • Inherent non-inductive design • Superior surge handling capability > 600 V (1.2 / 50 μs pulse) • Meets active and passive flammability requirements as defined in IEC 60115-1 and UL 94 V-0 DESCRIPTION • Radial version is available The specially developed product PR02-FS can be used for applications in which defined fusible characteristics and high voltage pulse handling is required. So this makes it easy for designers to meet safety requirements in their designs by selecting such products. Main applications are in lighting electronics. • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS • All general purpose power applications • Lighting ballast • Lighting electronics • Snubber resistor for inductive loads TECHNICAL SPECIFICATIONS DESCRIPTION DIN size Resistance range Resistance tolerance PR02-FS 0411 1  to 100  ± 10 %; ± 20 % Temperature coefficient ± 250 ppm/K Operating Temperature -55 °C to +200 °C Rated dissipation, P70 2W E-series Generic specification E12 (± 10 % and ± 20 %) IEC 60115-1 Stability after: Endurance at 70 °C; 1000 h R max.: ± (5 % R + 0.1 ) Damp heat, steady state (56 days) R max.: ± (3 % R + 0.1 ) Resistance to soldering heat (10 s, 260 °C) Revision: 27-Apr-2021 R max.: ± (0.5 % R + 0.05 ) Document Number: 28915 1 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PR02-FS www.vishay.com Vishay BCcomponents PART NUMBER AND PRODUCT DESCRIPTION Part Number: PR02FS0206809KA100 P R 0 2 F S 0 2 TYPE VARIANT WIRE TYPES TCR / MATERIAL PR02FS 0 = neutral 2 = Cu 0.78 0 = standard 0 6 8 0 9 K A 1 0 0 RESISTANCE TOLERANCE PACKAGING SPECIAL 3 digit value 1 digit multiplier Multiplier 8 = *10-2 9 = *10-1 0 = *100 K = ± 10 % M = ± 20 % N3 A1 A7 R5 00 = standard Product Description: PR02-FS 10 % A1 68R PR02-FS 10 % A1 68R TYPE TOLERANCE PACKAGING RESISTANCE VALUE PR02-FS 10 % N3 A1 A7 R5 68R = 68  PACKAGING TYPE CODE QUANTITY STYLE DESCRIPTION PITCH WIDTH PACKAGING DIMENSIONS N3 3000 Radial Ammo pack acc. to IEC 60286-2 12.7 mm - 45 mm x 262 mm x 330 mm A1 1000 Axial Ammo pack acc. to IEC 60286-1 5 mm 52 mm 72 mm x 60 mm x 258 mm A7 1000 Axial Ammo pack acc. to IEC 60286-1 5 mm 73 mm 95 mm x 74 mm x 260 mm R5 5000 Axial Reel pack acc. to IEC 60286-1 5 mm 52 mm 100 mm x 375 mm x 375 mm PR02-FS Revision: 27-Apr-2021 Document Number: 28915 2 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PR02-FS www.vishay.com Vishay BCcomponents DESCRIPTION ASSEMBLY A homogeneous film of metal alloy is deposited on a high grade ceramic body. Tinned connecting wires of electrolytic copper are welded to the end-caps. The resistors are coated with a red, non-flammable lacquer conformal coating which provides electrical, mechanical and climatic protection. This coating is not resistant to aggressive fluxes and cleaning solvents. The encapsulation is resistant to all cleaning solvents in accordance with IEC 60068-2-45. The nominal resistance and tolerance are marked on the resistor using colored bands in accordance with IEC 60062, marking codes for resistors and capacitors. An additional black color band is applied to differentiate the PR02-FS from standard PR02 product. The resistors are suitable for processing on automatic insertion equipment and cutting and bending machines. Excellent solderability is proven, even after extended storage. They are suitable for automatic soldering using wave or dipping. The resistors are completely lead (Pb)-free, the pure tin plating provides compatibility with lead (Pb)-free and lead-containing soldering processes. The immunity of the plating against tin whisker growth, in compliance with IEC 60068-2-82, has been proven under extensive testing. The encapsulant is resistant to cleaning solvent specified in IEC 60115-1. The suitability of conformal coatings, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. APPROVALS Additional marking for identification of PR02-FS product MATERIALS Vishay acknowledges the following systems for the regulation of hazardous substances: • IEC 62474, Material Declaration for Products of and for the Electrotechnical Industry, with the list of declarable substances given therein (1) • The Global Automotive Declarable Substance List (GADSL) (2) • The REACH regulation (1907/2006/EC) and the related list of substances with very high concern (SVHC) (3) for its supply chain The products do not contain any of the banned substances as per IEC 62474, GADSL, or the SVHC list, see www.vishay.com/how/leadfree. Hence the products fully comply with the following directives: • 2000/53/EC End-of-Life Vehicle Directive (ELV) and Annex II (ELV II) • 2011/65/EU Restriction of the Use of Hazardous Substances Directive (RoHS) with amendment 2015/863/EU • 2012/19/EU Waste Electrical and Electronic Equipment Directive (WEEE) Vishay pursues the elimination of conflict minerals from its supply chain, see the Conflict Minerals Policy at www.vishay.com/doc?49037. The PR02-FS series is specially designed to meet all safety requirements defined in UL1412. Essentially all tests are carried out in accordance with IEC 60115-1 specification, category -55 °C / +200 °C / 56 days (rated temperature range: lower category temperature, upper category temperature; damp heat, long term, 56 days). The tests are carried out in accordance with IEC 60068-2-xx. Test method under standard atmospheric conditions according to IEC 60068-1, 5.3. RELATED PRODUCTS For more information on products with higher wattage, higher pulse load capability and metal oxide film technology, please refer to the WK/WR datasheet at the link: www.vishay.com/doc?20128 For products with higher rated dissipation with small body size, with metal film technology, please refer to the PR01, PR02, PR03 datasheet at the link: www.vishay.com/doc?28729 Notes (1) The IEC 62474 list of declarable substances is maintained in a dedicated database, which is available at http://std.iec.ch/iec62474 (2) The Global Automotive Declarable Substance List (GADSL) is maintained by the American Chemistry Council, and available at www.gadsl.org (3) The SVHC list is maintained by the European Chemical Agency (ECHA) and available at http://echa.europa.eu/candidate-list-table Revision: 27-Apr-2021 Document Number: 28915 3 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PR02-FS www.vishay.com Vishay BCcomponents FUNCTIONAL PERFORMANCE Power in % The power that the resistor can dissipate depends on the ambient temperature. 100 80 60 40 20 0 -55 0 50 100 70 150 200 Ambient Temperature in °C Derating Peak Pulse Voltage in V Maximum dissipation (Pmax.) in percentage of rated power as a function of the ambient temperature (Tamb) 700 600 500 400 300 200 100 0 0 10 20 30 40 50 60 70 80 90 100 Resistance in Ω Maximum Fusing Time in s Pulse performance w.r.t. IEC 61000-4-5 after 10 pulses (5 positive and 5 negative with 30 s repetition time) of 1.2/50 μs are applied 18.0 16.0 14.0 12.0 1 Ω to 8.2 Ω 10.0 8.0 6.0 10 Ω to 100 Ω 4.0 2.0 0.0 60 70 80 90 100 Overload Power in W Fusing performance in response to defined overload Revision: 27-Apr-2021 Document Number: 28915 4 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PR02-FS Peak Power in W www.vishay.com Vishay BCcomponents 10 000 1000 100 10 1 10-5 10-4 10-3 10-2 10-1 100 101 Pulse Duration (s) Pulse performance after a rectangular pulse of defined duration is applied TEST PROCEDURES AND REQUIREMENTS All tests are carried out in accordance with the following specifications: • IEC 60115-1, generic specification (includes tests) Unless otherwise specified the following values apply: • Temperature: 15 °C to 35 °C • Relative humidity: 25 % to 75 % The test and requirements table contains only the most important tests. For the full test schedule refer to the documents listed above. The tests are carried out in accordance with IEC 60068-2-xx test method and under standard atmospheric conditions in accordance with IEC 60068-1, 4.3. Climatic category LCT / UCT / 56 (rated temperature range: lower category temperature, upper category temperature; damp heat, steady state, test duration: 56 days) is valid. • Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar) For performing some of the tests, the components are mounted on a test board in accordance with IEC 60115-1, 4.31. In test procedures and requirements table, only the tests and requirements are listed with reference to the relevant clauses of IEC 60115-1 and IEC 60068-2-xx test methods. A short description of the test procedure is also given. TEST PROCEDURES AND REQUIREMENTS IEC 60068-2TEST METHOD TEST 4.4.1 - Visual examination 4.4.2 - Dimensions (outline) 4.5 - Resistance 4.6.1.1 - Insulation resistance 500 V after 1 min; metal block method Rins min.: 104 M 4.7 - Voltage proof Uins = 500 VRMS; 60 s No breakdown or flashover 4.8 - Temperature coefficient At (20 / -55 / 20) °C and (20 / 155 / 20) °C  ± 250 ppm/K 4.16 21 (Ua1) 21 (Ub) 21 (Uc) Robustness of terminations Tensile, bending, and torsion No damage Rmax.: ± (0.5 % R + 0.05 ) IEC 60115-1 CLAUSE Revision: 27-Apr-2021 PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE ( Rmax.) No holes; clean surface; no damage Gauge (mm) See Dimensions table ± 10 % R ± 20 % R Document Number: 28915 5 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PR02-FS www.vishay.com Vishay BCcomponents TEST PROCEDURES AND REQUIREMENTS IEC 60115-1 CLAUSE IEC 60068-2TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE ( Rmax.) +235 °C; 2 s; solder bath method; SnPb40 Good tinning ( 95 % covered, no visible damage) +245 °C; 3 s; solder bath method; SnAg3Cu0.5 Good tinning ( 95 % covered, no visible damage) 4.17 20 (Ta) Solderability 4.18 20 (Tb) Resistance to soldering heat Unmounted components (260 ± 5) °C; (10 ± 1) s Rmax.: ± (0.5 % R + 0.05 ) 4.19 14 (Na) Rapid change of temperature 30 min at -55 °C and 30 min at +200 °C; 5 cycles No visual damage Rmax.: ± (1 % R + 0.05 ) 4.20 29 (Eb) Bump 3 x 1500 bumps in three directions; 40 g No damage Rmax.: ± (0.5 % R + 0.05 ) 4.22 6 (Fc) Vibration 10 sweep cycles per direction; 10 Hz to 2000 Hz; 1.5 mm or 200 m/s2 No damage Rmax.: ± (0.5 % R + 0.05 ) 4.23 4.23.2 Climatic sequence: 2 (Bb) Dry heat 200 °C; 16 h 4.23.3 30 (Db) Damp heat, cyclic 55 °C; 24 h; 90 % to 100 % RH; 1 cycle 4.23.4 1 (Ab) Cold -55 °C; 2 h 4.23.5 13 (M) Low air pressure 8.5 kPa; 2 h; 15 °C to 35 °C 4.23.6 30 (Db) Damp heat, cyclic 55 °C; 24 h; 95 % to 100 % RH; 5 cycles 4.24 78 (Cab) Damp heat (steady state) (40 ± 2) °C; 56 days; (93 ± 3 )% RH Rmax.: ± (3 % R + 0.1 ) 4.25.1 - Endurance (at 70 °C) U = P 70 x R ; 1.5 h on; 0.5 h off; 70 °C; 1000 h Rmax.: ± (5 % R + 0.1 ) 4.26 - Active flammability Accidental overload test No damage, no flaming of gauze cylinder 4.30 45 (Xa) Solvent resistance for marking Isopropyl alcohol (used in industrial application) +23 °C; toothbrush method Marking legible; no visible damage 4.35 - Passive flammability Needle flame test No ignition of product, no ignition of under layer burning time is less than 30 s Revision: 27-Apr-2021 Rins min.: 103 M Rmax.: ± (1.5 % R + 0.1 ) Document Number: 28915 6 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PR02-FS www.vishay.com Vishay BCcomponents DIMENSIONS D d L1 L2 Type with straight leads DIMENSIONS - Straight lead type and relevant physical dimensions; see straight leads outline TYPE Ø DMAX. (mm) L1 MAX. (mm) L2 MAX. (mm) Ød (mm) MASS (mg) 3.9 10.0 12.0 0.78 ± 0.05 504 PR02-FS PR02-FS WITH RADIAL TAPING Height for insertion (max.) = 29 mm P2 DIMENSIONS in millimeters P H1 H H0 L L1 W0 W α α F α = 30° to 40° a a Revision: 27-Apr-2021 P0 P1 D0 Pitch of components P 12.7 ± 1.0 Feed-hole pitch P0 12.7 ± 0.2 Feed-hole center to lead  at topside at the tape P1 3.85 ± 0.5 Feed-hole center to body center P2 6.35 ± 1.0 Lead spacing F 4.8 +0.7/-0 Width of carrier tape W 18.0 ± 0.5 Minimum hold down tape width W0 5.5 Height for insertion (max.) H1 29 Lead wire clinch height H0 16.5 ± 0.5 Body to hole center H 19.5 ± 1 Feed-hole diameter D0 4.0 ± 0.2 Height for cutting (max.) L 11.0 Minimum lead wire (tape portion) shortest lead L1 2.5 Document Number: 28915 7 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000