SI5441BDC-T1-GE3

Si5441BDC Vishay Siliconix P-Channel 2.5-V (G-S) MOSFET FEATURES PRODUCT SUMMARY VDS (V) RDS(on) (Ω) ID (A) 0.045 at VGS = - 4.5 V - 6.1 - 20 0.052 at VGS = - 3.6 V - 5.7 0.080 at VGS = - 2.5 V - 4.6 Qg (Typ.) 11.5 • Halogen-free According to IEC 61249-2-21 Available • TrenchFET® Power MOSFET 1206-8 ChipFET® 1 D D S D D D D G Marking Code S G BK XX Lot Traceability and Date Code Part # Code Bottom View D Ordering Information: Si5441BDC-T1-E3 (Lead (Pb)-free) Si5441BDC-T1-GE3 (Lead (Pb)-free and Halogen-free) P-Channel MOSFET ABSOLUTE MAXIMUM RATINGS TA = 25 °C, unless otherwise noted Parameter Symbol 5s Steady State Drain-Source Voltage VDS - 20 Gate-Source Voltage VGS ± 12 TA = 25 °C Continuous Drain Current (TJ = 150 °C)a TA = 85 °C Continuous Source Currenta IS TA = 25 °C Maximum Power Dissipationa TA = 85 °C PD - 4.4 - 4.4 - 3.2 - 20 - 2.1 - 1.1 2.5 1.3 1.3 0.7 TJ, Tstg Operating Junction and Storage Temperature Range V - 6.1 IDM Pulsed Drain Current Soldering Recommendations (Peak Temperature) ID - 55 to 150 b, c Unit A W °C 260 THERMAL RESISTANCE RATINGS Parameter Maximum Junction-to-Ambienta Maximum Junction-to-Foot (Drain) Symbol t≤5s Steady State Steady State RthJA RthJF Typical Maximum 48 50 85 95 17 20 Unit °C/W Notes: a. Surface Mounted on 1" x 1" FR4 board. b. See Reliability Manual for profile. The ChipFET is a leadless package. The end of the lead terminal is exposed copper (not plated) as a result of the singulation process in manufacturing. A solder fillet at the exposed copper tip cannot be guaranteed and is not required to ensure adequate bottom side solder interconnection. c. Rework Conditions: manual soldering with a soldering iron is not recommended for leadless components. Document Number: 73207 S-83054-Rev. B, 29-Dec-08 www.vishay.com 1 Si5441BDC Vishay Siliconix SPECIFICATIONS TJ = 25 °C, unless otherwise noted Parameter Symbol Test Conditions Min. - 0.6 Typ. Max. Unit Static VGS(th) VDS = VGS, ID = - 250 µA Gate-Body Leakage IGSS VDS = 0 V, VGS = ± 12 V Zero Gate Voltage Drain Current IDSS On-State Drain Currenta ID(on) Gate Threshold Voltage Drain-Source On-State Resistance a Diode Forward Voltage a V nA VDS = - 20 V, VGS = 0 V -1 VDS = - 20 V, VGS = 0 V, TJ = 85 °C -5 VDS ≤ - 5 V, VGS = - 4.5 V µA - 20 A VGS = - 4.5 V, ID = - 4.4 A 0.036 0.045 VGS = - 3.6 V, ID = - 4.2 A 0.042 0.052 VGS = - 2.5 V, ID = - 1.3 A 0.065 0.080 gfs VDS = - 10 V, ID = - 4.4 A 12 VSD IS = - 1.1 A, VGS = 0 V - 0.8 - 1.2 11.5 22 RDS(on) Forward Transconductancea - 1.4 ± 100 Ω S V Dynamicb Total Gate Charge Qg Gate-Source Charge Qgs Gate-Drain Charge Qgd Gate Resistance Turn-On Delay Time VDS = - 10 V, VGS = - 4.5 V, ID = - 4.4 A 3.7 10 15 25 50 75 VDD = - 10 V, RL = 10 Ω ID ≅ - 1 A, VGEN = - 4.5 V, Rg = 6 Ω td(off) Turn-Off Delay Time Ω Rg td(on) tr Rise Time nC 2.2 Fall Time tf Source-Drain Reverse Recovery Time trr IF = - 1.1 A, dI/dt = 100 A/µs 50 75 50 75 30 60 ns Notes: a. Pulse test; pulse width ≤ 300 µs, duty cycle ≤ 2 %. b. Guaranteed by design, not subject to production testing. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted 20 20 TC = - 55 °C VGS = 5 thru 3 V 16 16 I D - Drain Current (A) I D - Drain Current (A) 25 °C 2.5 V 12 8 2V 125 °C 12 8 4 4 1.5 V 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 VDS - Drain-to-Source Voltage (V) Output Characteristics www.vishay.com 2 3.5 4.0 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 VGS - Gate-to-Source Voltage (V) Transfer Characteristics Document Number: 73207 S-83054-Rev. B, 29-Dec-08 Si5441BDC Vishay Siliconix TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted 0.16 1200 0.14 Ciss C - Capacitance (pF) R DS(on) - On-Resistance (Ω) 1000 0.12 0.10 0.08 VGS = 2.5 V 0.06 VGS = 3.6 V 800 600 400 Coss 0.04 VGS = 4.5 V 0.02 200 Crss 0.00 0 0 4 8 12 16 20 0 4 ID - Drain Current (A) 8 16 20 VDS - Drain-to-Source Voltage (V) On-Resistance vs. Drain Current Capacitance 1.6 5 VGS = 4.5 V ID = 6.1 A VDS = 10 V ID = 6.1 A 1.4 4 R DS(on) - On-Resistance (Normalized) VGS - Gate-to-Source Voltage (V) 12 3 2 1.2 1.0 0.8 1 0.6 - 50 0 0 3 6 9 12 15 - 25 0 25 50 75 100 125 Qg - Total Gate Charge (nC) TJ - Junction Temperature (°C) Gate Charge On-Resistance vs. Junction Temperature 150 0.12 20 TJ = 150 °C R DS(on) - On-Resistance (Ω) 0.10 I S - Source Current (A) 10 TJ = 25 °C 0.08 ID = 6.1 A 0.06 0.04 0.02 1 0.0 0.00 0.2 0.4 0.6 0.8 1.0 1.2 0 1 2 3 4 VSD - Source-to-Drain Voltage (V) VGS - Gate-to-Source Voltage (V) Source-Drain Diode Forward Voltage On-Resistance vs. Gate-to-Source Voltage Document Number: 73207 S-83054-Rev. B, 29-Dec-08 5 www.vishay.com 3 Si5441BDC Vishay Siliconix TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted 0.4 50 40 ID = 250 µA 0.2 Power (W) V GS(th) Variance (V) 0.3 0.1 30 20 0.0 10 - 0.1 - 0.2 - 50 - 25 0 25 50 75 100 125 0 10-3 150 10-2 10-1 TJ - Temperature (°C) 1 10 100 600 Time (s) Threshold Voltage Single Pulse Power 100 IDM Limited Limited by RDS(on)* I D - Drain Current (A) 10 P(t) = 0.0001 P(t) = 0.001 1 ID(on) Limited P(t) = 0.01 P(t) = 0.1 P(t) = 1 P(t) = 10 DC TC = 25 °C Single Pulse 0.1 BVDSS Limited 0.01 0.1 1 10 100 VDS - Drain-to-Source Voltage (V) * VGS > minimum V GS at which R DS(on) is specified Safe Operating Area 2 Normalized Effective Transient Thermal Impedance 1 Duty Cycle = 0.5 0.2 Notes: 0.1 PDM 0.1 0.05 t1 t2 1. Duty Cycle, D = t1 t2 2. Per Unit Base = R thJA = 80 °C/W 0.02 3. T JM - TA = PDMZthJA(t) Single Pulse 4. Surface Mounted 0.01 10-4 10-3 10-2 10-1 1 Square Wave Pulse Duration (s) 10 100 600 Normalized Thermal Transient Impedance, Junction-to-Ambient www.vishay.com 4 Document Number: 73207 S-83054-Rev. B, 29-Dec-08 Si5441BDC Vishay Siliconix TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted 2 Normalized Effective Transient Thermal Impedance 1 Duty Cycle = 0.5 0.2 0.1 0.1 0.05 0.02 Single Pulse 0.01 10-4 10-3 10-2 10-1 Square Wave Pulse Duration (s) 1 10 Normalized Thermal Transient Impedance, Junction-to-Foot Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?73207. Document Number: 73207 S-83054-Rev. B, 29-Dec-08 www.vishay.com 5 Package Information Vishay Siliconix 1206-8 ChipFETR 4 L D 8 7 6 5 4 1 S 2 e 3 E1 5 6 7 8 4 3 2 1 E 4 b x c Backside View 2X 0.10/0.13 R C1 A DETAIL X NOTES: 1. All dimensions are in millimeaters. 2. Mold gate burrs shall not exceed 0.13 mm per side. 3. Leadframe to molded body offset is horizontal and vertical shall not exceed 0.08 mm. 4. Dimensions exclusive of mold gate burrs. 5. No mold flash allowed on the top and bottom lead surface. MILLIMETERS Dim A b c c1 D E E1 e L S INCHES Min Nom Max Min Nom Max 1.00 − 1.10 0.039 − 0.043 0.25 0.30 0.35 0.010 0.012 0.014 0.1 0.15 0.20 0.004 0.006 0.008 0 − 0.038 0 − 0.0015 2.95 3.05 3.10 0.116 0.120 0.122 1.825 1.90 1.975 0.072 0.075 0.078 1.55 1.65 1.70 0.061 0.065 0.067 0.65 BSC 0.28 − 0.0256 BSC 0.42 0.011 − 0.55 BSC 0.022 BSC 5_Nom 5_Nom 0.017 ECN: C-03528—Rev. F, 19-Jan-04 DWG: 5547 Document Number: 71151 15-Jan-04 www.vishay.com 1 AN811 Vishay Siliconix Single-Channel 1206-8 ChipFETr Power MOSFET Recommended Pad Pattern and Thermal Performance INTRODUCTION New Vishay Siliconix ChipFETs in the leadless 1206-8 package feature the same outline as popular 1206-8 resistors and capacitors but provide all the performance of true power semiconductor devices. The 1206-8 ChipFET has the same footprint as the body of the LITTLE FOOTR TSOP-6, and can be thought of as a leadless TSOP-6 for purposes of visualizing board area, but its thermal performance bears comparison with the much larger SO-8. 80 mil 68 mil This technical note discusses the single-channel ChipFET 1206-8 pin-out, package outline, pad patterns, evaluation board layout, and thermal performance. 28 mil 26 mil PIN-OUT Figure 1 shows the pin-out description and Pin 1 identification for the single-channel 1206-8 ChipFET device. The pin-out is similar to the TSOP-6 configuration, with two additional drain pins to enhance power dissipation and thermal performance. The legs of the device are very short, again helping to reduce the thermal path to the external heatsink/pcb and allowing a larger die to be fitted in the device if necessary. Single 1206-8 ChipFET 1 D D D D The pad pattern with copper spreading shown in Figure 2 improves the thermal area of the drain connections (pins 1,2,3,6.7,8) while remaining within the confines of the basic footprint. The drain copper area is 0.0054 sq. in. or 3.51 sq. mm). This will assist the power dissipation path away from the device (through the copper leadframe) and into the board and exterior chassis (if applicable) for the single device. The addition of a further copper area and/or the addition of vias to other board layers will enhance the performance still further. An example of this method is implemented on the Vishay Siliconix Evaluation Board described in the next section (Figure 3). D D G S Bottom View FIGURE 1. For package dimensions see the 1206-8 ChipFET package outline drawing (http://www.vishay.com/doc?71151). BASIC PAD PATTERNS The basic pad layout with dimensions is shown in Application Note 826, Recommended Minimum Pad Patterns With Outline Drawing Access for Vishay Siliconix MOSFETs, (http://www.vishay.com/doc?72286). This is sufficient for low power dissipation MOSFET applications, but power semiconductor performance requires a greater copper pad area, particularly for the drain leads. Document Number: 71126 12-Dec-03 FIGURE 2. Footprint With Copper Spreading THE VISHAY SILICONIX EVALUATION BOARD FOR THE SINGLE 1206-8 The ChipFET 1206-08 evaluation board measures 0.6 in by 0.5 in. Its copper pad pattern consists of an increased pad area around the six drain leads on the top-side—approximately 0.0482 sq. in. 31.1 sq. mm—and vias added through to the underside of the board, again with a maximized copper pad area of approximately the board-size dimensions. The outer package outline is for the 8-pin DIP, which will allow test sockets to be used to assist in testing. The thermal performance of the 1206-8 on this board has been measured with the results following on the next page. The testing included comparison with the minimum recommended footprint on the evaluation board-size pcb and the industry standard one-inch square FR4 pcb with copper on both sides of the board. www.vishay.com 1 AN811 Vishay Siliconix Front of Board Back of Board ChipFETr vishay.com FIGURE 3. Junction-to-Foot Thermal Resistance (the Package Performance) Thermal performance for the 1206-8 ChipFET measured as junction-to-foot thermal resistance is 15_C/W typical, 20_C/W maximum for the single device. The “foot” is the drain lead of the device as it connects with the body. This is identical to the SO-8 package RQjf performance, a feat made possible by shortening the leads to the point where they become only a small part of the total footprint area. Junction-to-Ambient Thermal Resistance (dependent on pcb size) The typical RQja for the single-channel 1206-8 ChipFET is 80_C/W steady state, compared with 68_C/W for the SO-8. Maximum ratings are 95_C/W for the 1206-8 versus 80_C/W for the SO-8. The results show that a major reduction can be made in the thermal resistance by increasing the copper drain area. In this example, a 45_C/W reduction was achieved without having to increase the size of the board. If increasing board size is an option, a further 33_C/W reduction was obtained by maximizing the copper from the drain on the larger 1” square pcb. 160 Thermal Resistance (C/W) THERMAL PERFORMANCE 120 Single EVB Min. Footprint 80 1” Square PCB 40 Testing To aid comparison further, Figure 4 illustrates ChipFET 1206-8 thermal performance on two different board sizes and three different pad patterns. The results display the thermal performance out to steady state and produce a graphic account of how an increased copper pad area for the drain connections can enhance thermal performance. The measured steady state values of RQja for the single 1206-8 ChipFET are : 1) Minimum recommended pad pattern (see Figure 2) on the evaluation board size of 0.5 in x 0.6 in. 156_C/W 2) The evaluation board with the pad pattern described on Figure 3. 111_C/W 3) Industry standard 1” square pcb with maximum copper both sides. 78_C/W www.vishay.com 2 0 10-5 10-4 10-3 10-2 10-1 1 10 100 1000 Time (Secs) FIGURE 4. Single 1206−8 ChipFET SUMMARY The thermal results for the single-channel 1206-8 ChipFET package display similar power dissipation performance to the SO-8 with a footprint reduction of 80%. Careful design of the package has allowed for this performance to be achieved. The short leads allow the die size to be maximized and thermal resistance to be reduced within the confines of the TSOP-6 body size. ASSOCIATED DOCUMENT 1206-8 ChipFET Dual Thermal performance, AN812 (http://www.vishay.com/doc?71127). Document Number: 71126 12-Dec-03 Application Note 826 Vishay Siliconix RECOMMENDED MINIMUM PADS FOR 1206-8 ChipFET® 0.093 0.026 0.016 0.010 (0.650) (0.406) (0.244) 0.036 (0.914) 0.022 (0.559) (2.032) 0.080 (2.357) Recommended Minimum Pads Dimensions in Inches/(mm) Return to Index APPLICATION NOTE Return to Index www.vishay.com 2 Document Number: 72593 Revision: 21-Jan-08 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000