SIB441EDK-T1-GE3

SiB441EDK www.vishay.com Vishay Siliconix P-Channel 12 V (D-S) MOSFET FEATURES PowerPAK® SC-75-6L Single S 4 D 5 6 1. S 7 m m 1 1.6 mm Top View • TrenchFET® power MOSFET D 6 3 G Bottom View • Thermally enhanced PowerPAK® SC-75 package - Small footprint area - Low on-resistance 2 D 1 D • 100 % Rg tested • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 Marking code: BO APPLICATIONS PRODUCT SUMMARY VDS (V) RDS(on) max. () at VGS = -4.5 V RDS(on) max. () at VGS = -3.7 V RDS(on) max. () at VGS = -2.5 V RDS(on) max. () at VGS = -1.8 V RDS(on) max. () at VGS = -1.5 V Qg typ. (nC) ID (A) a Configuration • Typical ESD performance 2500 V -12 0.0255 0.0280 0.0360 0.0600 0.1150 13.4 9 Single S • Portable devices such as smart phones, tablet PCs, and mobile computing - Battery switch G - Load switch - Power management D P-Channel MOSFET ORDERING INFORMATION Package Lead (Pb)-free and halogen-free PowerPAK SC-75 SiB441EDK-T1-GE3 ABSOLUTE MAXIMUM RATINGS (TA = 25 °C, unless otherwise noted) PARAMETER Drain-source voltage Gate-source voltage Continuous drain current (TJ = 150 °C) SYMBOL VDS VGS TC = 25 °C TC = 70 °C TA = 25 °C TA = 70 °C Pulsed drain current (t = 300 μs) Continuous source-drain diode current Maximum power dissipation Operating junction and storage temperature range Soldering recommendations (peak temperature) d, e ID IDM TC = 25 °C TA = 25 °C TC = 25 °C TC = 70 °C TA = 25 °C TA = 70 °C IS PD TJ, Tstg LIMIT -12 ±8 -9 a -9 a -8.3 b, c -6.6 b, c -40 -9 a -2 b, c 13 8.4 2.4 b, c 1.6 b, c -55 to +150 260 UNIT V A W °C THERMAL RESISTANCE RATINGS PARAMETER SYMBOL TYPICAL MAXIMUM UNIT t5s RthJA 41 51 Maximum junction-to-ambient b, f °C/W Maximum junction-to-case (drain) Steady state RthJC 7.5 9.5 Notes a. Package limited b. Surface mounted on 1" x 1" FR4 board c. t = 5 s d. See solder profile (www.vishay.com/doc?73257). The PowerPAK SC-75 is a leadless package. The end of the lead terminal is exposed copper (not plated) as a result of the singulation process in manufacturing. A solder fillet at the exposed copper tip cannot be guaranteed and is not required to ensure adequate bottom side solder interconnection e. Rework conditions: manual soldering with a soldering iron is not recommended for leadless components f. Maximum under steady state conditions is 105 °C/W S13-0197-Rev. A, 28-Jan-13 Document Number: 62821 1 For technical questions, contact: pmostechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiB441EDK www.vishay.com Vishay Siliconix SPECIFICATIONS (TJ = 25 °C, unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT VDS VGS = 0 V, ID = -250 μA -12 - - - V -5 - - 2.7 - Static Drain-source breakdown voltage VDS/TJ VDS temperature coefficient VGS(th) temperature coefficient VGS(th)/TJ ID = -250 μA Gate-source threshold voltage VGS(th) VDS = VGS, ID = -250 μA -0.4 - -0.9 VDS = 0 V, VGS = ± 8 V - - ±4 VDS = 0 V, VGS = ± 4.5 V - - ±1 VDS = -12 V, VGS = 0 V - - -1 VDS = -12 V, VGS = 0 V, TJ = 55 °C - - -10 VDS  -5 V, VGS = -4.5 V -15 - - VGS = -4.5 V, ID = -4 A - 0.0210 0.0255 VGS = -3.7 V, ID = -4 A - 0.0230 0.0280 VGS = -2.5 V, ID = -2 A - 0.0290 0.0360 VGS = -1.8 V, ID = -2 A - 0.0420 0.0600 VGS = -1.5 V, ID = -0.5 A - 0.0570 0.1150 VDS = -6 V, ID = -4 A - 17 - - 1180 - - 265 - - 250 - - 22.1 33 - 13.4 20 VDS = -6 V, VGS = -4.5 V, ID = -2.1 A - 1.6 - - 3.4 - f = 1 MHz 2.2 11 22 - 22 45 - 42 85 - 60 120 tf - 50 100 td(on) - 7 15 - 10 20 Gate-source leakage Zero gate voltage drain current On-state drain current a Drain-source on-state resistance a Forward transconductance a IGSS IDSS ID(on) RDS(on) gfs mV/°C V μA A  S Dynamic b Input capacitance Ciss Output capacitance Coss Reverse transfer capacitance Crss Total gate charge Qg Gate-source charge Qgs Gate-drain charge Qgd Gate resistance Rg Turn-on delay time Rise time Turn-off delay time Fall time Turn-on delay time Rise time Turn-off delay time Fall time VDS = -6 V, VGS = 0 V, f = 1 MHz VDS = -6 V, VGS = -8 V, ID = -2.1 A td(on) tr td(off) tr td(off) VDD = -6 V, RL = 2.7  ID  -2.2 A, VGEN = -4.5 V, Rg = 1  VDD = -6 V, RL = 2.7  ID  -2.2 A, VGEN = -8 V, Rg = 1  tf - 60 120 - 52 100 pF nC  ns Drain-Source Body Diode Characteristics Continuous source-drain diode current IS Pulse diode forward current ISM Body diode voltage VSD Body diode reverse recovery time trr Body diode reverse recovery charge Qrr Reverse recovery fall time ta Reverse recovery rise time tb TC = 25 °C IS = -2.2 A, VGS = 0 V IF = -2.2 A, di/dt = 100 A/μs, TJ = 25 °C - - -9 - - -40 - -0.85 -1.2 - 30 60 ns - 12 25 nC - 9 - - 11 - A V ns Notes a. Pulse test; pulse width  300 μs, duty cycle  2 % b. Guaranteed by design, not subject to production testing Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. S13-0197-Rev. A, 28-Jan-13 Document Number: 62821 2 For technical questions, contact: pmostechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiB441EDK www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 30 10-1 10-2 10-3 IGSS - Gate Current (A) IGSS - Gate Current (mA) 25 20 TJ = 25 °C 15 10 10-4 TJ = 150 °C 10-5 10-6 TJ = 25 °C 10-7 5 10-8 0 10-9 0 4 8 12 16 0 4 8 12 16 VGS - Gate-Source Voltage (V) VGS - Gate-to-Source Voltage (V) Gate Current vs. Gate-Source Voltage Gate Current vs. Gate-Source Voltage 40 10 VGS = 5 V thru 3 V 8 ID - Drain Current (A) ID - Drain Current (A) VGS = 2.5 V 30 20 VGS = 2 V 6 4 TC = 25 °C 10 TC = 125 °C 2 VGS = 1.5 V TC = - 55 °C 0 0 0.0 VDS - Drain-to-Source Voltage (V) 0.5 1.0 1.5 VGS - Gate-to-Source Voltage (V) Output Characteristics Transfer Characteristics 0.5 1.0 1.5 2.0 2.5 0.0 3.0 2.0 2000 0.15 VGS = 1.5 V 1600 Ciss C - Capacitance (pF) RDS(on) - On-Resistance (Ω) 0.12 VGS = 1.8 V 0.09 VGS = 2.5 V 0.06 800 Coss VGS = 3.7 V 0.03 1200 400 Crss VGS = 4.5 V 0 0 0 10 20 30 40 0 2 4 6 8 ID - Drain Current (A) VDS - Drain-to-Source Voltage (V) On-Resistance vs. Drain Current Capacitance S13-0197-Rev. A, 28-Jan-13 10 12 Document Number: 62821 3 For technical questions, contact: pmostechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiB441EDK www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 1.4 ID = 2.1 A RDS(on) - On-Resistance (Normalized) VGS - Gate-to-Source Voltage (V) 8 VDS = 6 V 6 VDS = 3 V 4 VDS = 9.6 V 2 ID = 4 A VGS = 1.8 V 1.2 VGS = 1.5 V 1.1 1.0 0.9 0.8 0 0 5 10 15 20 25 - 50 - 25 0 25 50 75 100 125 150 Qg - Total Gate Charge (nC) TJ - Junction Temperature (°C) Gate Charge On-Resistance vs. Junction Temperature 0.16 100 ID = 4 A RDS(on) - On-Resistance (Ω) TJ = 150 °C IS - Source Current (A) VGS = 4.5 V, 3.7 V, 2.5 V 1.3 10 TJ = 25 °C 1 0.1 0.12 0.08 TJ = 125 °C 0.04 TJ = 25 °C 0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0 1 2 3 4 5 VSD - Source-to-Drain Voltage (V) VGS - Gate-to-Source Voltage (V) Source-Drain Diode Forward Voltage On-Resistance vs. Gate-to-Source Voltage 0.8 20 0.7 15 Power (W) VGS(th) (V) 0.6 0.5 ID = 250 μA 10 0.4 5 0.3 0.2 - 50 - 25 0 25 50 75 100 125 150 0 0.001 0.01 0.1 1 10 100 1000 TJ - Temperature (°C) Pulse (s) Threshold Voltage Single Pulse Power, Junction-to-Ambient S13-0197-Rev. A, 28-Jan-13 Document Number: 62821 4 For technical questions, contact: pmostechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiB441EDK www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 100 Limited by RDS(on)* ID - Drain Current (A) 10 100 µs 1 ms 1 10 ms 100 ms 10 s 1s DC 0.1 TA = 25 °C BVDSS Limited 0.01 0.1 1 10 100 VDS - Drain-to-Source Voltage (V) * VGS > minimum VGS at which RDS(on) is specified 20 15 16 12 Power (W) ID - Drain Current (A) Safe Operating Area, Junction-to-Ambient 12 Package Limited 9 8 6 4 3 0 0 0 25 50 75 100 125 150 25 50 75 100 TC - Case Temperature (°C) TC - Case Temperature (°C) Current Derating a Power Derating 125 150 Note a. The power dissipation PD is based on TJ max. = 150 °C, using junction-to-case thermal resistance, and is more useful in settling the upper dissipation limit for cases where additional heatsinking is used. It is used to determine the current rating, when this rating falls below the package limit S13-0197-Rev. A, 28-Jan-13 Document Number: 62821 5 For technical questions, contact: pmostechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiB441EDK www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 1 Normalized Effective Transient Thermal Impedance Duty Cycle = 0.5 0.2 0.1 0.1 Notes: PDM 0.05 t1 0.02 t2 1. Duty Cycle, D = t1 t2 2. Per Unit Base = R thJA = 105 °C/W Single Pulse 3. T JM - TA = PDMZthJA(t) 4. Surface Mounted 0.01 10-4 10-3 10-2 10-1 1 Square Wave Pulse Duration (s) 10 100 1000 Normalized Thermal Transient Impedance, Junction-to-Ambient 1 Normalized Effective Transient Thermal Impedance Duty Cycle = 0.5 0.2 0.1 0.05 0.02 Single Pulse 0.1 10-4 10-3 10-2 10-1 Square Wave Pulse Duration (s) Normalized Thermal Transient Impedance, Junction-to-Case                      Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package / tape drawings, part marking, and reliability data, see www.vishay.com/ppg?62821. S13-0197-Rev. A, 28-Jan-13 Document Number: 62821 6 For technical questions, contact: pmostechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Package Information Vishay Siliconix b e PIN1 b e PIN3 PIN2 PIN1 PIN3 PIN6 K3 PIN5 E1 E1 K K D1 D1 D1 E3 E1 D2 K E2 K4 L PIN2 L PowerPAK® SC75-6L PIN6 K2 PIN4 K1 K2 BACKSIDE VIEW OF SINGLE PIN5 K1 PIN4 K2 BACKSIDE VIEW OF DUAL D A E Notes: 1. All dimensions are in millimeters 2. Package outline exclusive of mold flash and metal burr 3. Package outline inclusive of plating C A1 Z z DETAIL Z SINGLE PAD DIM A MILLIMETERS DUAL PAD INCHES MILLIMETERS INCHES Min Nom Max Min Nom Max Min Nom Max Min Nom Max 0.675 0.75 0.80 0.027 0.030 0.032 0.675 0.75 0.80 0.027 0.030 0.032 A1 0 - 0.05 0 - 0.002 0 - 0.05 0 - 0.002 b 0.18 0.25 0.33 0.007 0.010 0.013 0.18 0.25 0.33 0.007 0.010 0.013 C 0.15 0.20 0.25 0.006 0.008 0.010 0.15 0.20 0.25 0.006 0.008 0.010 D 1.53 1.60 1.70 0.060 0.063 0.067 1.53 1.60 1.70 0.060 0.063 0.067 D1 0.57 0.67 0.77 0.022 0.026 0.030 0.34 0.44 0.54 0.013 0.017 0.021 D2 0.10 0.20 0.30 0.004 0.008 0.012 E 1.53 1.60 1.70 0.060 0.063 0.067 1.53 1.60 1.70 0.060 0.063 0.067 E1 1.00 1.10 1.20 0.039 0.043 0.047 0.51 0.61 0.71 0.020 0.024 0.028 E2 0.20 0.25 0.30 0.008 0.010 0.012 E3 0.32 0.37 0.42 0.013 0.015 0.017 e 0.50 BSC 0.020 BSC 0.50 BSC 0.020 BSC K 0.180 TYP 0.007 TYP 0.245 TYP 0.010 TYP K1 0.275 TYP 0.011 TYP 0.320 TYP 0.013 TYP K2 0.200 TYP 0.008 TYP 0.200 BSC 0.008 TYP K3 0.255 TYP 0.010 TYP K4 0.300 TYP L 0.15 0.25 0.012 TYP 0.35 T 0.006 0.010 0.014 0.15 0.25 0.35 0.006 0.010 0.014 0.03 0.08 0.13 0.001 0.003 0.005 ECN: C-07431 − Rev. C, 06-Aug-07 DWG: 5935 Document Number: 73000 06-Aug-07 www.vishay.com 1 Application Note 826 Vishay Siliconix RECOMMENDED PAD LAYOUT FOR PowerPAK® SC75-6L Single 1.250 (0.049) 0.250 (0.01) 0.500 (0.02) 0.250 (0.01) 0.400 (0.016) 0.300 (0.012) 0.180 (0.007) 0.370 (0.015) 1.700 (0.067) 1.100 0.620 (0.024) (0.043) 2.000 (0.079) 0.200 (0.008) 0.300 (0.012) 0.300 (0.012) 1 0.545 (0.021) 0.250 (0.01) 0.670 (0.026) 2.000 (0.079) Dimensions in mm/(Inches) Return to Index APPLICATION NOTE Document Number: 70488 Revision: 21-Jan-08 www.vishay.com 13 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000