SIHF30N60E-GE3

SiHF30N60E www.vishay.com Vishay Siliconix E Series Power MOSFET FEATURES PRODUCT SUMMARY VDS (V) at TJ max. • • • • • • 650 RDS(on) max. at 25 °C () VGS = 10 V Qg max. (nC) 0.125 130 Qgs (nC) 15 Qgd (nC) 39 Configuration Single Low figure-of-merit (FOM) Ron x Qg Low input capacitance (Ciss) Reduced switching and conduction losses Ultra low gate charge (Qg) Available Avalanche energy rated (UIS) Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 D TO-220 FULLPAK APPLICATIONS • • • • Server and telecom power supplies Switch mode power supplies (SMPS) Power factor correction power supplies (PFC) Lighting - High-intensity discharge (HID) - Fluorescent ballast lighting - LED lighting • Industrial - Welding - Induction heating - Motor drives • Battery chargers • Renewable energy - Solar (PV inverters) G G D S S N-Channel MOSFET ORDERING INFORMATION Package TO-220 FULLPAK Lead (Pb)-free and Halogen-free SiHF30N60E-GE3 Lead (Pb)-free SiHF30N60E-E3 ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless otherwise noted) PARAMETER SYMBOL LIMIT Drain-Source Voltage VDS 600 Gate-Source Voltage VGS ± 30 Continuous Drain Current (TJ = 150 °C) d Pulsed Drain VGS at 10 V TC = 25 °C TC = 100 °C Current a ID IDM Linear Derating Factor UNIT V 29 18 A 76 0.29 W/°C mJ Single Pulse Avalanche Energy b EAS 690 Maximum Power Dissipation PD 37 W TJ, Tstg -55 to +150 °C Operating Junction and Storage Temperature Range Drain-Source Voltage Slope VDS = 0 V to 80 % VDS Reverse Diode dV/dt e Soldering Recommendations (Peak temperature) c Mounting Torque dV/dt 70 18 V/ns for 10 s 300 °C M3 screw 0.6 Nm Notes a. Repetitive rating; pulse width limited by maximum junction temperature. b. VDD = 50 V, starting TJ = 25 °C, L = 28.2 mH, Rg = 25 , IAS = 7 A. c. 1.6 mm from case. d. Limited by maximum junction temperature. e. ISD  ID, dI/dt = 100 A/μs, starting TJ = 25 °C. S16-1084-Rev. I, 06-Jun-16 Document Number: 91454 1 For technical questions, contact: hvm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiHF30N60E www.vishay.com Vishay Siliconix THERMAL RESISTANCE RATINGS PARAMETER SYMBOL TYP. MAX. Maximum Junction-to-Ambient RthJA - 65 Maximum Junction-to-Case (Drain) RthJC - 3.4 UNIT °C/W SPECIFICATIONS (TJ = 25 °C, unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Static Drain-Source Breakdown Voltage VDS Temperature Coefficient Gate-Source Threshold Voltage (N) VDS VGS = 0 V, ID = 250 μA 600 - - V VDS/TJ Reference to 25 °C, ID = 250 μA - 0.64 - V/°C VGS(th) VDS = VGS, ID = 250 μA 2.0 2.8 4.0 V VGS = ± 20 V - - ± 100 nA VGS = ± 30 V - - ±1 μA VDS = 600 V, VGS = 0 V - - 1 VDS = 600 V, VGS = 0 V, TJ = 150 °C - - 100 Gate-Source Leakage IGSS Zero Gate Voltage Drain Current IDSS μA - 0.104 0.125  gfs VDS = 8 V, ID = 3 A - 5.4 - S Input Capacitance Ciss 2600 - Coss - 138 - Reverse Transfer Capacitance Crss VGS = 0 V, VDS = 100 V, f = 1.0 MHz - Output Capacitance - 3 - Effective Output Capacitance, Energy Related a Co(er) - 98 - Effective Output Capacitance, Time Related b Co(tr) - 346 - - 85 130 - 15 - Drain-Source On-State Resistance Forward Transconductancea RDS(on) VGS = 10 V ID = 15 A Dynamic pF VDS = 0 V to 480 V, VGS = 0 V Total Gate Charge Qg Gate-Source Charge Qgs VGS = 10 V ID = 15 A, VDS = 480 V Gate-Drain Charge Qgd - 39 - Turn-On Delay Time td(on) - 19 40 Rise Time Turn-Off Delay Time tr td(off) Fall Time tf Gate Input Resistance Rg nC VDD = 380 V, ID = 15 A, VGS = 10 V, Rg = 4.7  - 32 65 - 63 95 - 36 75 f = 1 MHz, open drain - 0.63 - - - 29 - - 65 - - 1.3 V - 402 605 ns ns  Drain-Source Body Diode Characteristics Continuous Source-Drain Diode Current IS Pulsed Diode Forward Current ISM Diode Forward Voltage VSD Body Diode Reverse Recovery Time Body Diode Reverse Recovery Charge Reverse Recovery Current MOSFET symbol showing the  integral reverse p - n junction diode D Qrr S TJ = 25 °C, IS = 15 A, VGS = 0 V trr IRRM A G TJ = 25 °C, IF = IS = 15 A, dI/dt = 100 A/μs, VR = 20 V - 7 15 μC - 32 65 A Notes a. Coss(er) is a fixed capacitance that gives the same energy as Coss while VDS is rising from 0 % to 80 % VDSS. b. Coss(tr) is a fixed capacitance that gives the same charging time as Coss while VDS is rising from 0 % to 80 % VDSS. S16-1084-Rev. I, 06-Jun-16 Document Number: 91454 2 For technical questions, contact: hvm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiHF30N60E www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 80 3.0 TOP 15 V 14 V 13 V 12 V 11 V 10 V 9.0 V 8.0 V 7.0 V 6.0 V BOTTOM 5.0 V ID - Drain Current (A) 60 TJ = 25 °C 50 40 30 20 VGS = 10 V 2.0 1.5 1.0 0.5 5V 10 ID = 15 A 2.5 RDS(on) - On-Resistance (Normalized) 70 0.0 0 0 5 10 15 20 25 - 60 - 40 - 20 30 0 20 40 60 80 100 120 140 160 TJ - Junction Temperature (°C) VDS - Drain-to-Source Voltage (V) Fig. 1 - Typical Output Characteristics, TC = 25 °C Fig. 4 - Normalized On-Resistance vs. Temperature 50 10 000 Ciss TOP 15 V 14 V 13 V 12 V 11 V 10 V 9.0 V 8.0 V 7.0 V 6.0 V BOTTOM 5.0 V 30 20 VGS = 0 V, f = 1 MHz Ciss = Cgs + Cgd x Cds shorted Crss = Cgd Coss = Cds + Cgd 1000 C - Capacitance (pF) ID - Drain Current (A) 40 100 Coss 10 10 Crss TJ = 150 °C 1 0 0 5 10 15 20 25 0 30 100 200 300 400 500 600 VDS - Drain-to-Source Voltage (V) VDS - Drain-to-Source Voltage (V) Fig. 2 - Typical Output Characteristics, TC = 150 °C Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage 80 18 16 TJ = 25 °C 14 2000 TJ = 150 °C 40 10 Coss Eoss 8 200 Eoss (μJ) 12 Coss (pF) ID, Drain Current (A) 60 6 20 4 2 0 20 0 5 10 15 20 VGS, Gate-to-Source Voltage (V) Fig. 3 - Typical Transfer Characteristics S16-1084-Rev. I, 06-Jun-16 25 0 0 100 200 300 400 500 600 VDS Fig. 6 - Coss and Eoss vs. VDS Document Number: 91454 3 For technical questions, contact: hvm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiHF30N60E www.vishay.com Vishay Siliconix 24 30.0 VDS = 300 V 25.0 VDS = 120 V 16 VDS = 480 V 12 8 ID, Drain Current (A) VGS - Gate-to-Source Voltage (V) ID = 15 A 20 20.0 15.0 10.0 4 5.0 0 0 0 25 50 75 100 125 150 25 50 75 Fig. 7 - Typical Gate Charge vs. Gate-to-Source Voltage 150 Fig. 10 - Maximum Drain Current vs. Case Temperature 1000 VDS, Drain-to-Source Breakdown Voltage (V) 725 100 IS - Source Current (A) 125 TC - Temperature (°C) Qg - Total Gate Charge (nC) TJ = 150 °C 10 1 TJ = 25 °C 0.1 0.01 0.001 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 VSD - Source-to-Drain Voltage (V) Operation in this Area Limited by RDS(on) 100 700 675 650 625 600 575 550 - 60 - 40 - 20 0 20 40 60 80 100 120 140 160 TJ - Temperature (°C) Fig. 8 - Typical Source-Drain Diode Forward Voltage Fig. 11 - Temperature vs. Drain-to-Source Voltage IDM Limited 10 ID, Drain Current (A) 100 100 μs Limited by RDS(on)* 1 1 ms 10 ms 0.1 TC = 25 °C TJ = 150 °C Single Pulse 0.01 1 BVDSS Limited 10 100 1000 VDS, Drain-to-Source Voltage (V) * VGS > minimum VGS at which RDS(on) is specified Fig. 9 - Maximum Safe Operating Area S16-1084-Rev. I, 06-Jun-16 Document Number: 91454 4 For technical questions, contact: hvm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiHF30N60E www.vishay.com Vishay Siliconix 1 Normalized Effective Transient Thermal Impedance Duty Cycle = 0.5 0.2 0.1 0.1 0.05 0.02 Single Pulse 0.01 0.0001 0.001 0.01 0.1 1 Square Wave Pulse Duration (s) Fig. 12 - Normalized Thermal Transient Impedance, Junction-to-Case VGS VDS RD VDS tp VDD D.U.T. RG + - VDD VDS 10 V Pulse width ≤ 1 µs Duty factor ≤ 0.1 % IAS Fig. 16 - Unclamped Inductive Waveforms Fig. 13 - Switching Time Test Circuit VDS 90 % QG 10 V QGS 10 % VGS QGD VG td(on) td(off) tf tr Fig. 14 - Switching Time Waveforms Charge Fig. 17 - Basic Gate Charge Waveform L Vary tp to obtain required IAS VDS Current regulator Same type as D.U.T. D.U.T RG + - IAS V DD 50 kΩ 12 V 0.2 µF 0.3 µF 10 V tp + 0.01 Ω Fig. 15 - Unclamped Inductive Test Circuit D.U.T. - VDS VGS 3 mA IG ID Current sampling resistors Fig. 18 - Gate Charge Test Circuit S16-1084-Rev. I, 06-Jun-16 Document Number: 91454 5 For technical questions, contact: hvm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiHF30N60E www.vishay.com Vishay Siliconix Peak Diode Recovery dV/dt Test Circuit + D.U.T. Circuit layout considerations • Low stray inductance • Ground plane • Low leakage inductance current transformer + - - Rg • • • • + dV/dt controlled by Rg Driver same type as D.U.T. ISD controlled by duty factor “D” D.U.T. - device under test + - VDD Driver gate drive P.W. Period D= P.W. Period VGS = 10 Va D.U.T. lSD waveform Reverse recovery current Body diode forward current dI/dt D.U.T. VDS waveform Diode recovery dV/dt Re-applied voltage Inductor current VDD Body diode forward drop Ripple ≤ 5 % ISD Note a. VGS = 5 V for logic level devices Fig. 19 - For N-Channel           Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?91454. S16-1084-Rev. I, 06-Jun-16 Document Number: 91454 6 For technical questions, contact: hvm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Package Information www.vishay.com Vishay Siliconix TO-220 FULLPAK (High Voltage) OPTION 1: FACILITY CODE = 9 A F G Q1 E D ØR A3 L1 3 x b2 3 x b1 Mold flash bleeding Q L Exposed Cu 3xb 2xe C Bottom view MILLIMETERS DIM. MIN. NOM. A 4.60 4.70 4.80 b 0.70 0.80 0.91 b1 1.20 1.30 1.47 b2 1.10 1.20 1.30 C 0.45 0.50 0.63 D 15.80 15.87 15.97 e MAX. 2.54 BSC E 10.00 10.10 F 2.44 2.54 10.30 2.64 G 6.50 6.70 6.90 L 12.90 13.10 13.30 L1 3.13 3.23 3.33 Q 2.65 2.75 2.85 Q1 3.20 3.30 3.40 ØR 3.08 3.18 3.28 Notes 1. To be used only for process drawing 2. These dimensions apply to all TO-220 FULLPAK leadframe versions 3 leads 3. All critical dimensions should C meet Cpk > 1.33 4. All dimensions include burrs and plating thickness 5. No chipping or package damage 6. Facility code will be the 1st character located at the 2nd row of the unit marking Revision: 08-Apr-2019 Document Number: 91359 1 For technical questions, contact: hvmos.techsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Package Information www.vishay.com Vishay Siliconix OPTION 2: FACILITY CODE = Y A A1 E ØP n d1 d3 D u L1 V L b3 A2 b2 c b MILLIMETERS INCHES DIM. MIN. MAX. MIN. MAX. A 4.570 4.830 0.180 0.190 A1 2.570 2.830 0.101 0.111 A2 2.510 2.850 0.099 0.112 b 0.622 0.890 0.024 0.035 b2 1.229 1.400 0.048 0.055 b3 1.229 1.400 0.048 0.055 c 0.440 0.629 0.017 0.025 D 8.650 9.800 0.341 0.386 d1 15.88 16.120 0.622 0.635 d3 12.300 12.920 0.484 0.509 E 10.360 10.630 0.408 e 2.54 BSC 0.419 0.100 BSC L 13.200 13.730 0.520 0.541 L1 3.100 3.500 0.122 0.138 n 6.050 6.150 0.238 0.242 ØP 3.050 3.450 0.120 0.136 u 2.400 2.500 0.094 0.098 V 0.400 0.500 0.016 0.020 ECN: E19-0180-Rev. D, 08-Apr-2019 DWG: 5972 Notes 1. To be used only for process drawing 2. These dimensions apply to all TO-220 FULLPAK leadframe versions 3 leads 3. All critical dimensions should C meet Cpk > 1.33 4. All dimensions include burrs and plating thickness 5. No chipping or package damage 6. Facility code will be the 1st character located at the 2nd row of the unit marking Revision: 08-Apr-2019 Document Number: 91359 2 For technical questions, contact: hvmos.techsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000