SM15T68A-E3/57T

SM15T Series www.vishay.com Vishay General Semiconductor Surface Mount TRANSZORB® Transient Voltage Suppressors FEATURES • Low profile package Available • Ideal for automated placement • Glass passivated chip junction • Available in unidirectional and bidirectional • 1500 W peak pulse power capability with a 10/1000 μs waveform Available SMC (DO-214AB) Cathode • Excellent clamping capability Anode (unidirectional) • Low inductance (bidirectional) LINKS TO ADDITIONAL RESOURCES 3D 3D • Meets MSL level 1, per J-STD-020, LF maximum peak of 260 °C • AEC-Q101 qualified available - Automotive ordering code: base P/NHE3 or P/NHM3 • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 3D Models TYPICAL APPLICATIONS PRIMARY CHARACTERISTICS VWM 5.8 V to 188 V VBR unidirectional 6.8 V to 220 V VBR bidirectional 6.8 V to 220 V PPPM 1500 W PD 6.5 W IFSM (uni-directional only) 200 A TJ max. 150 °C Polarity Unidirectional, bidirectional Package SMC (DO-214AB) DEVICES FOR BIDIRECTION APPLICATIONS For bidirectional devices use CA suffix (e.g. SM15T12CA). Electrical characteristics apply in both directions. APPLICATION NOTES A 1500 W (SMC) device is normally selected when the threat of transients is from lightning induced transients, conducted via external leads or I/O lines. It is also used to protect against switching transients induced by large coils or industrial motors. Source impedance at component level in a system is usually high enough to limit the current within the peak pulse current (IPP) rating of this series. In an overstress condition, the failure mode is a short circuit. Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive, and telecommunication. MECHANICAL DATA Case: SMC (DO-214AB) Molding compound meets UL 94 V-0 flammability rating Base P/N-E3 - RoHS-compliant and commercial grade Base P/N-M3 - halogen-free, RoHS-compliant, commercial grade Base P/NHE3_X - RoHS-compliant and AEC-Q101 qualified Base P/NHM3_X - halogen-free, RoHS-compliant, and AEC-Q101 qualified (“_X” denotes revision code e.g. A, B, ...) Terminals: matte tin plated leads, solderable per J-STD-002 and JESD 22-B102 E3, M3, HE3, and HM3 suffix meets JESD 201 class 2 whisker test Polarity: for unidirectional types the band denotes cathode end, no marking on bidirectional types MAXIMUM RATINGS (TA = 25 °C unless otherwise noted) PARAMETER SYMBOL VALUE UNIT Peak power dissipation with a 10/1000 μs waveform (1)(2) (fig. 1) PPPM 1500 W Peak pulse current with a 10/1000 μs waveform (1) (fig. 3) IPPM See next table A PD 6.5 W IFSM 200 A TJ, TSTG -65 to +150 °C Power dissipation on infinite heatsink at TA = 50 °C Peak forward surge current 10 ms single half sine-wave uni-directional only (2) Operating junction and storage temperature range Notes (1) Non-repetitive current pulse, per fig. 3 and derated above T = 25 °C per fig. 2 A (2) Mounted on 0.31" x 0.31" (8.0 mm x 8.0 mm) copper pads to each terminal Revision: 19-Apr-2021 Document Number: 88380 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SM15T Series www.vishay.com Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted) TYPE (1) DEVICE MARKING CODE BREAKDOWN VOLTAGE VBR AT IT (2) (V) MIN. MAX. TEST CURRENT IT (mA) STAND-OFF VOLTAGE VRM (V) LEAKAGE CURRENT IRM AT VRM ID (3) (μA) CLAMPING VOLTAGE VC AT IPPM (10/1000 μs) CLAMPING VOLTAGE VC AT IPPM (8/20 μs) (V) (V) (A) αT MAX. 10-4/°C UNI BI (A) SM15T6V8A GDE7 GDE7 6.45 7.14 10 5.80 1000 10.5 143 13.4 746 5.7 SM15T7V5A GDK7 BDK7 7.13 7.88 10 6.40 500 11.3 132 14.5 690 6.1 SM15T10A GDT7 BDT7 9.50 10.5 1.0 8.55 10 14.5 103 18.6 538 7.3 SM15T12A GDX7 BDX7 11.4 12.6 1.0 10.2 5.0 16.7 90.0 21.7 461 7.8 SM15T15A GEG7 GEG7 14.3 15.8 1.0 12.8 1.0 21.2 71.0 27.2 368 8.4 SM15T18A GEM7 BEM7 17.1 18.9 1.0 15.3 1.0 25.2 59.5 32.5 308 8.8 SM15T22A GET7 BET7 20.9 23.1 1.0 18.8 1.0 30.6 49.0 39.3 254 9.2 SM15T24A GEV7 GEV7 22.8 25.2 1.0 20.5 1.0 33.2 45.0 42.8 234 9.4 SM15T27A GEX7 BEX7 25.7 28.4 1.0 23.1 1.0 37.5 40.0 48.3 207 9.6 SM15T30A GFE7 BFE7 28.5 31.5 1.0 25.6 1.0 41.5 36.0 53.5 187 9.7 SM15T33A GFG7 GFG7 31.4 34.7 1.0 28.2 1.0 45.7 33.0 59.0 169 9.8 SM15T36A GFK7 BFK7 34.2 37.8 1.0 30.8 1.0 49.9 30.0 64.3 156 9.9 SM15T39A GFM7 BFM7 37.1 41.0 1.0 33.3 1.0 53.9 28.0 69.7 143 10.0 SM15T68A GGG7 GGG7 64.6 71.4 1.0 58.1 1.0 92.0 16.3 121 83 10.4 SM15T100A GGV7 GGV7 95.0 105 1.0 85.5 1.0 137 11.0 178 56 10.6 SM15T150A GHK7 GHK7 143 158 1.0 128 1.0 207 7.20 265 38 10.8 SM15T200A GHR7 GHR7 190 210 1.0 171 1.0 274 5.50 353 28 10.8 SM15T220A GHR8 GHR8 209 231 1.0 188 1.0 328 4.60 388 26 10.8 Notes (1) For bidirectional devices add suffix “CA” instead of “A” (2) V BR measured after IT applied for 300 μs square wave pulse (3) For bi-polar devices with V RM = 10 V or under, the IRM limit is doubled THERMAL CHARACTERISTICS (TA = 25 °C unless otherwise noted) PARAMETER SYMBOL VALUE Typical thermal resistance, junction to ambient air (1) RθJA 75 Typical thermal resistance, junction to lead RθJL 15 UNIT °C/ W Note (1) Mounted on minimum recommended pad layout ORDERING INFORMATION (Example) PREFERRED P/N SM15T10A-E3/57T SM15T10A-M3/57T SM15T10A-E3/9AT SM15T10A-M3/9AT SM15T10AHE3_A/H (1) SM15T10AHM3_A/H (1) SM15T10AHE3_A/I (1) SM15T10AHM3_A/I (1) UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE 0.211 57T 850 7" diameter plastic tape and reel 0.211 9AT 3500 13" diameter plastic tape and reel 0.211 H 850 7" diameter plastic tape and reel 0.211 I 3500 13" diameter plastic tape and reel Note AEC-Q101 qualified (1) Revision: 19-Apr-2021 Document Number: 88380 2 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SM15T Series www.vishay.com Vishay General Semiconductor RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted) 20 000 100 Measured at Zero Bias 10 1 0.31 x 0.31" (8.0 x 8.0 mm) Copper Pad Areas 0.1 0.1 µs 1000 VR, Measured at Stand-Off Voltage, VWM 100 Uni-Directional Bi-Directional TJ = 25 °C f = 1.0 MHz Vsig = 50 mVp-p 10 1.0 µs 10 µs 100 µs 1.0 ms 1 10 ms 10 100 400 td - Pulse Width (s) VWM - Reverse Stand-Off Voltage (V) Fig. 1 - Peak Pulse Power Rating Curve Fig. 4 - Typical Junction Capacitance Uni-Directional 100 100 Transient Thermal Impedance (°C/W) Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % CJ - Junction Capacitance (pF) PPPM - Peak Pulse Power (kW) 10 000 75 50 25 25 50 75 100 125 150 175 1.0 0.1 0.001 0 0 10 200 0.01 0.1 1 10 100 1000 TJ - Initial Temperature (°C) t - Pulse Duration (s) Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature Fig. 5 - Typical Transient Thermal Impedance Peak Value IPPM 100 200 TJ = 25 °C Pulse Width (td) is defined as the Point where the Peak Current decays to 50 % of IPPM tr = 10 µs Peak Forward Surge Current (A) IPPM - Peak Pulse Current, % IRSM 150 Half Value - IPP IPPM 2 50 10/1000 µs Waveform as defined by R.E.A. 100 TJ = TJ max. 8.3 ms Single Half Sine-Wave td 0 10 0 1.0 2.0 3.0 4.0 1 10 100 t - Time (ms) Number of Cycles at 60 Hz Fig. 3 - Pulse Waveform Fig. 6 - Maximum Non-Repetitive Forward Surge Current Unidirectional Use Only Revision: 19-Apr-2021 Document Number: 88380 3 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SM15T Series www.vishay.com Vishay General Semiconductor PACKAGE OUTLINE DIMENSIONS in inches (millimeters) SMC (DO-214AB) Mounting Pad Layout Cathode Band 0.185 (4.69) MAX. 0.126 (3.20) 0.246 (6.22) 0.220 (5.59) 0.114 (2.90) 0.126 (3.20) MIN. 0.280 (7.11) 0.060 (1.52) MIN. 0.260 (6.60) 0.012 (0.305) 0.006 (0.152) 0.320 REF. 0.103 (2.62) 0.079 (2.06) 0.060 (1.52) 0.030 (0.76) 0.008 (0.2) 0 (0) 0.320 (8.13) 0.305 (7.75) Revision: 19-Apr-2021 Document Number: 88380 4 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2023 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2023 1 Document Number: 91000