TPSMC24HE3_A/H

TPSMC6.8 thru TPSMC47A www.vishay.com Vishay General Semiconductor Surface Mount PAR® Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions FEATURES • Junction passivation optimized design passivated anisotropic rectifier technology • TJ = 185 °C capability suitable for high reliability and automotive requirement • Available in uni-directional polarity only • 1500 W peak pulse power capability with a 10/1000 μs waveform DO-214AB (SMC) • Excellent clamping capability • Very fast response time • Low incremental surge resistance • Meets MSL level 1, per J-STD-020, LF maximum peak of 260 °C PRIMARY CHARACTERISTICS VBR 6.8 V to 47 V VWM 5.50 V to 40.2 V PPPM 1500 W IFSM 200 A TJ max. 185 °C Polarity Uni-directional Package DO-214AB (SMC) TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive, and telecommunication. • AEC-Q101 qualified • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 MECHANICAL DATA Case: DO-214AB (SMC) Molding compound meets UL 94 V-0 flammability rating Base P/NHE3_X - RoHS-compliant and AEC-Q101 qualified (“X” denotes revision code e.g. A, B, ..., revision code only applicable for part number with ± 5 % tolerance) Terminals: matte tin plated leads, solderable J-STD-002 and JESD 22-B102 HE3 suffix meets JESD 201 class 2 whisker test per Polarity: color band denotes cathode end MAXIMUM RATINGS (TA = 25 °C, unless otherwise noted) PARAMETER SYMBOL VALUE UNIT Peak pulse power dissipation with a 10/1000 μs waveform (fig. 3) (1)(2) PPPM 1500 W Peak power pulse current with a 10/1000 μs waveform (fig. 1) (1) IPPM See table next page A Peak forward surge current 8.3 ms single half sine-wave (2)(3) IFSM 200 A Maximum instantaneous forward voltage at 100 A (2)(3) Operating junction and storage temperature range VF 3.5 V TJ, TSTG -65 to +185 °C Notes (1) Non-repetitive current pulse, per fig. 3 and derated above T = 25 °C per fig. 2 A (2) Mounted on 0.31" x 0.31" (8.0 mm x 8.0 mm) copper pads at each terminal (3) Measured on 8.3 ms single half sine-wave, or equivalent square wave, duty cycle = 4 pulses per minute maximum Revision: 22-Jul-16 Document Number: 88407 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TPSMC6.8 thru TPSMC47A www.vishay.com Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 °C, unless otherwise noted) DEVICE TYPE DEVICE MARKING CODE BREAKDOWN VOLTAGE VBR (1) AT IT (V) TEST CURRENT IT (mA) STAND-OFF VOLTAGE VWM (V) MAXIMUM REVERSE LEAKAGE AT VWM IR (μA) MAXIMUM REVERSE LEAKAGE AT VWM TJ = 150 °C ID (μA) MAXIMUM PEAK PULSE SURGE CURRENT IPPM (2) (A) MAXIMUM CLAMPING VOLTAGE AT IPPM VC (V) MIN. MAX. TPSMC6.8 DDP 6.12 7.48 10 5.5 1000 10000 139 10.8 TPSMC6.8A DEP 6.45 7.14 10 5.8 1000 10000 143 10.5 TPSMC7.5 DFP 6.75 8.25 10 6.05 500 5000 128 11.7 TPSMC7.5A DGP 7.13 7.88 10 6.4 500 5000 133 11.3 TPSMC8.2 DHP 7.38 9.02 10 6.63 200 2000 120 12.5 TPSMC8.2A DKP 7.79 8.61 10 7.02 200 2000 124 12.1 TPSMC9.1 DLP 8.19 10 1 7.37 50 500 109 13.8 TPSMC9.1A DMP 8.65 9.55 1 7.78 50 500 112 13.4 TPSMC10 DNP 9 11 1 8.1 20 200 100 15 TPSMC10A DPP 9.5 10.5 1 8.55 20 200 103 14.5 TPSMC11 DQP 9.9 12.1 1 8.92 5 50 92.6 16.2 TPSMC11A DRP 10.5 11.6 1 9.4 5 50 96.2 15.6 TPSMC12 DSP 10.8 13.2 1 9.72 2 10 86.7 17.3 TPSMC12A DTP 11.4 12.6 1 10.2 2 10 89.8 16.7 TPSMC13 DUP 11.7 14.3 1 10.5 2 10 78.9 19 TPSMC13A DVP 12.4 13.7 1 11.1 2 10 82.4 18.2 TPSMC15 DWP 13.5 16.5 1 12.1 1 10 68.2 22 TPSMC15A DXP 14.3 15.8 1 12.8 1 10 70.8 21.2 TPSMC16 DYP 14.4 17.6 1 12.9 1 10 63.8 23.5 TPSMC16A DZP 15.2 16.8 1 13.6 1 10 66.7 22.5 TPSMC18 EDP 16.2 19.8 1 14.5 1 10 56.6 26.5 TPSMC18A EEP 17.1 18.9 1 15.3 1 10 59.5 25.2 TPSMC20 EFP 18 22 1 16.2 1 10 51.5 29.1 TPSMC20A EGP 19 21 1 17.1 1 10 54.2 27.7 TPSMC22 EHP 19.8 24.2 1 17.8 1 10 47 31.9 TPSMC22A EKP 20.9 23.1 1 18.8 1 10 49 30.6 TPSMC24 ELP 21.6 26.4 1 19.4 1 10 43.2 34.7 TPSMC24A EMP 22.8 25.2 1 20.5 1 10 45.2 33.2 TPSMC27 ENP 24.3 29.7 1 21.8 1 10 38.4 39.1 TPSMC27A EPP 25.7 28.4 1 23.1 1 10 40 37.5 TPSMC30 EQP 27 33 1 24.3 1 10 34.5 43.5 TPSMC30A ERP 28.5 31.5 1 25.6 1 10 36.2 41.4 TPSMC33 ESP 29.7 36.3 1 26.8 1 10 31.4 47.7 TPSMC33A ETP 31.4 34.7 1 28.2 1 10 32.8 45.7 TPSMC36 EUP 32.4 39.6 1 29.1 1 15 28.8 52 TPSMC36A EVP 34.2 37.8 1 30.8 1 15 30.1 49.9 TPSMC39 EWP 35.1 42.9 1 31.6 1 15 26.6 56.4 TPSMC39A EXP 37.1 41 1 33.3 1 15 27.8 53.9 TPSMC43 EYP 38.7 47.3 1 34.8 1 20 24.2 61.9 TPSMC43A EZP 40.9 45.2 1 36.8 1 20 25.3 59.3 TPSMC47 FDP 42.3 51.7 1 38.1 1 20 22.1 67.8 TPSMC47A FEP 44.7 49.4 1 40.2 1 20 23.1 64.8 Notes (1) V BR measured after IT applied for 300 μs, IT = square wave pulse or equivalent (2) Surge current waveform per fig. 3 and derated per fig. 2 (3) All terms and symbols are consistent with ANSI/IEEE C62.35 Revision: 22-Jul-16 Document Number: 88407 2 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TPSMC6.8 thru TPSMC47A www.vishay.com Vishay General Semiconductor ORDERING INFORMATION (Example) PREFERRED P/N UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE TPSMC6.8AHE3_A/H (1) 0.211 H 850 7" diameter plastic tape and reel TPSMC6.8AHE3_A/I (1) 0.211 I 3500 13" diameter plastic tape and reel 0.211 H 850 7" diameter plastic tape and reel 0.211 I 3500 13" diameter plastic tape and reel TPSMC6.8AHE3_B/H (1) TPSMC6.8AHE3_B/I (1) Note (1) AEC-Q101 qualified RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted) 150 TA = 25 °C Non-Repetitive Pulse Waveform shown in Fig. 3 10 1.0 0.31 x 0.31" (8.0 x 8.0 mm) Copper Pad Areas TJ = 25 °C Pulse Width (td) is defined as the Point where the Peak Current decays to 50 % of IPPM tr = 10 µs Peak Value IPPM 100 Half Value - IPP IPPM 2 50 10/1000 µs Waveform as defined by R.E.A. td 0 1.0 µs 10 µs 100 µs 1.0 ms 10 ms 0 1.0 2.0 3.0 td - Pulse Width (s) t - Time (ms) Fig. 1 - Peak Pulse Power Rating Curve Fig. 3 - Pulse Waveform 4.0 10 000 100 VR, measured at Zero Bias Junction Capacitance (pF) Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % 0.1 0.1 µs IPPM - Peak Pulse Current, % IRSM PPPM - Peak Power (kW) 100 75 50 25 1000 VR measured at Stand-Off Voltage, VWM 100 TJ = 25 °C f = 1.0 MHz Vsig = 50 mVp-p 10 0 0 50 100 150 200 1 10 TJ - Initial Temperature (°C) VBR - Breakdown Voltage (V) Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature Fig. 4 - Typical Junction Capacitance 100 Revision: 22-Jul-16 Document Number: 88407 3 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TPSMC6.8 thru TPSMC47A www.vishay.com Vishay General Semiconductor Peak Forward Surge Current (A) 200 TJ = TJ max. 8.3 ms Single Half Sine-Wave 100 50 10 1 5 10 50 100 Number of Cycles at 60 Hz Fig. 5 - Maximum Non-Repetitive Peak Forward Surge Current  PACKAGE OUTLINE DIMENSIONS in inches (millimeters) DO-214AB (SMC) Cathode Band Mounting Pad Layout 0.185 (4.69) MAX. 0.246 (6.22) 0.220 (5.59) 0.126 (3.20) 0.114 (2.90) 0.126 (3.20) MIN. 0.280 (7.11) 0.260 (6.60) 0.060 (1.52) MIN. 0.012 (0.305) 0.006 (0.152) 0.320 (8.13) REF. 0.103 (2.62) 0.079 (2.06) 0.060 (1.52) 0.030 (0.76) 0.008 (0.2) 0 (0) 0.320 (8.13) 0.305 (7.75) Revision: 22-Jul-16 Document Number: 88407 4 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer  ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Revision: 13-Jun-16 1 Document Number: 91000