TSOP331.., TSOP333.., TSOP335..
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Very low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Supply voltage: 2.5 V to 5.5 V
• Improved immunity against ambient light
• Insensitive to supply voltage ripple and noise
• Compatible with wave or reflow soldering
(see “P” version of Minimold option datasheets)
• Material categorization: for definitions of
compliance please see www.vishay.com/doc?99912
23051
MECHANICAL DATA
LINKS TO ADDITIONAL RESOURCES
Pinning for TSOP33...:
3D 3D
Product Page
3D Models
Holders
Bends and Cuts
Calculators
Marking
1 = OUT, 2 = GND, 3 = VS
Packages
ORDERING CODE
TSOP33... - 1800 pieces in bags
DESCRIPTION
BLOCK DIAGRAM
The TSOP33... series are miniaturized IR receiver modules
for infrared remote control systems. A PIN diode and a
preamplifier are assembled on lead frame, the epoxy
package contains an IR filter.
16833-13
3
30 kΩ
The demodulated output signal can be directly connected to
a microprocessor for decoding.
1
Input
The TSOP333.. series devices are optimized to suppress
almost all spurious pulses from energy saving lamps like
CFLs. AGC3 may also suppress some data signals if
continuously transmitted.
Band
pass
AGC
Demodulator
2
PIN
The TSOP331.. series are provided primarily for
compatibility with old AGC1 designs. New designs should
prefer the TSOP333.. series containing the newer AGC3.
The TSOP335.. series contain a very robust AGC5. This
series should only be used for critically noisy environments.
Control circuit
APPLICATION CIRCUIT
17170-11
Transmitter
with
TSALxxxx
R1
IR receiver
VS
Circuit
These components have not been qualified according to
automotive specifications.
+ VS
C1
μC
OUT
GND
VO
GND
R1 and C1 recommended to reduce supply ripple for VS < 2.8 V
Rev. 1.6, 05-Aug-2021
1
Document Number: 82742
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP331.., TSOP333.., TSOP335..
www.vishay.com
Vishay Semiconductors
PARTS TABLE
LEGACY, FOR SHORT BURSTS
(AGC1)
AGC
Carrier frequency
FOR SHORT BURSTS, NOISY
FOR SHORT BURSTS, VERY
ENVIRONMENTS (AGC3)
NOISY ENVIRONMENTS (AGC5)
30 kHz
TSOP33130
TSOP33330
TSOP33530
33 kHz
TSOP33133
TSOP33333
TSOP33533
36 kHz
TSOP33136
TSOP33336 (1)(2)(7)
TSOP33536
38 kHz
TSOP33138
TSOP33338 (3)(4)(5)(6)
TSOP33538
40 kHz
TSOP33140
TSOP33340
TSOP33540
56 kHz
TSOP33156
TSOP33356
TSOP33556
Package
Minimold
Pinning
1 = OUT, 2 = GND, 3 = VS
Dimensions (mm)
5.4 W x 6.35 H x 4.9 D
Mounting
Leaded
Application
Best choice for
Special options
Remote control
(1)
MCIR
(2)
RCMM
(3)
Mitsubishi
(4)
RECS-80 Code
(5)
r-map
(6)
XMP-1, XMP-2
(7)
RCMM
• Narrow optical filter: www.vishay.com/doc?81590
• Wide optical filter: www.vishay.com/doc?82726
• Low voltage option: www.vishay.com/doc?82382
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
VS
-0.3 to +6
V
mA
Supply voltage
Supply current
IS
3
Output voltage
VO
-0.3 to (VS + 0.3)
V
Output current
IO
5
mA
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
Soldering temperature
Tj
100
°C
Tstg
-25 to +85
°C
Tamb
-25 to +85
°C
Tamb ≤ 85 °C
Ptot
10
mW
t ≤ 10 s, 1 mm from case
Tsd
260
°C
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
Supply current
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
Ev = 0, VS = 3.3 V
ISD
0.27
0.35
0.45
mA
Ev = 40 klx, sunlight
ISH
-
0.45
-
mA
VS
2.5
-
5.5
V
d
-
30
-
m
VOSL
-
-
100
mV
Supply voltage
Transmission distance
Output voltage low
Ev = 0, test signal see Fig. 1,
IR diode TSAL6200, IF = 50 mA
mW/m2,
IOSL = 0.5 mA, Ee = 0.7
test signal see Fig. 1
UNIT
Minimum irradiance
Pulse width tolerance:
tpi - 5/f0 < tpo < tpi + 6/f0,
test signal see Fig. 1
Ee min.
-
0.08
0.15
mW/m2
Maximum irradiance
tpi - 5/f0 < tpo < tpi + 6/f0,
test signal see Fig. 1
Ee max.
30
-
-
W/m2
Directivity
Angle of half transmission
distance
ϕ1/2
-
± 45
-
°
Rev. 1.6, 05-Aug-2021
2
Document Number: 82742
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP331.., TSOP333.., TSOP335..
www.vishay.com
Vishay Semiconductors
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Optical Test Signal
(IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms)
0.8
t
tpi *)
T
*) tpi ≥ 6/f0 is recommended for optimal function
Output Signal
VO
1)
2)
VOH
VOL
td
14337
3/f0 < td < 9/f0
tpi - 4/f0 < tpo < tpi + 6/f0
1)
tpo
ton
ton, toff - Output Pulse Width (ms)
Ee
0.7
0.6
0.5
toff
0.4
0.3
0.2
λ = 950 nm,
optical test signal, fig. 3
0.1
0
0.1
20744
t
2)
Ee min./Ee - Relative Responsivity
tpo - Output Pulse Width (ms)
0.35
0.30
Output pulse width
0.20
0.15
Input burst length
0.10
λ = 950 nm,
optical test signal, Fig. 1
10 000
1.0
0.8
0.6
0.4
f = f0 ± 5 %
Δf(3 dB) = f0/10
0.2
0.0
1
10
100
1000
10 000
0.7
Ee - Irradiance (mW/m²)
20760
Ee min. - Threshold Irradiance (mW/m²)
t
600 µs
t = 60 ms
94 8134
Output Signal, (see Fig. 4)
VOH
VOL
t on
t off
1.3
4.0
Correlation with ambient light sources:
3.5 10 W/m² = 1.4 klx (std. illum. A, T = 2855 K)
10 W/m² = 8.2 klx (daylight, T = 5900 K)
3.0
2.5
1.5
1.0
0.5
0
0.01
t
Fig. 3 - Output Function
Wavelength of ambient
illumination: λ = 950 nm
2.0
20745
Rev. 1.6, 05-Aug-2021
1.1
Fig. 5 - Frequency Dependence of Responsivity
Optical Test Signal
600 µs
0.9
f/f0 - Relative Frequency
16925
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
VO
1000
1.2
0
0.1
Ee
100
Fig. 4 - Output Pulse Diagram
0.40
0.05
10
Ee - Irradiance (mW/m²)
Fig. 1 - Output Active Low
0.25
1
0.1
1
10
100
Ee - Ambient DC Irradiance (W/m²)
Fig. 6 - Sensitivity in Bright Ambient
3
Document Number: 82742
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP331.., TSOP333.., TSOP335..
www.vishay.com
Vishay Semiconductors
1.0
2.0
f = f0
f = 30 kHz
f = 10 kHz
f = 100 Hz
1.5
1.0
0.5
0
1
10
100
0.8
0.7
1000
0.6
1st line
2nd line
2.5
10000
0.9
2nd line
S(λ)rel. - Relative Spectral Sensitivity
Ee min. - Threshold Irradiance (mW/m2)
Axis Title
3.0
0.5
0.4
100
0.3
0.2
0.1
1000
0
750
ΔVS RMS - AC Voltage on DC Supply Voltage (mV)
850
950
1050
10
1150
λ - Wavelength (nm)
23180
Fig. 10 - Relative Spectral Sensitivity vs. Wavelength
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
0°
10°
20°
1.0
30°
f = 38 kHz,
Ee = 2 mW/m²
Max. Envelope Duty Cycle
0.9
0.8
0.7
40°
TSOP331..
0.6
1.0
0.5
0.9
50°
0.8
60°
0.4
0.3
TSOP333..
0.2
70°
0.7
80°
0.1
TSOP335..
0
0
20
40
60
80
100
0.6
120
0.2
0
Fig. 11 - Horizontal Directivity
Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length
0.20
0.20
0.18
0.16
Ee min. - Sensitivity (mW/m2)
Ee min. - Threshold Irradiance (mW/m2)
0.4
drel - Relative Transmission Distance
Burst Length (Number of Cycles/Burst)
0.14
0.12
0.10
0.08
0.06
0.04
0.02
0
-30
-10
10
30
50
70
0.18
0.16
0.14
0.12
0.10
0.08
0.06
0.04
0.02
0.00
90
1
Tamb - Ambient Temperature (°C)
2
3
4
5
VS - Supply Voltage (V)
Fig. 9 - Sensitivity vs. Ambient Temperature
Fig. 12 - Sensitivity vs. Supply Voltage
Rev. 1.6, 05-Aug-2021
4
Document Number: 82742
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP331.., TSOP333.., TSOP335..
www.vishay.com
Vishay Semiconductors
SUITABLE DATA FORMAT
Axis Title
This series is designed to suppress spurious output pulses
due to noise or disturbance signals. The devices can
distinguish data signals from noise due to differences in
frequency, burst length, and envelope duty cycle. The data
signal should be close to the device’s band-pass center
frequency (e.g. 38 kHz) and fulfill the conditions in the table
below.
10000
7
When a data signal presented to the device in the
presence of a disturbance, the sensitivity of the receiver is
automatically reduced by the AGC to insure that no spurious
pulses are present at the receiver’s output. Some examples
which are suppressed are:
5
1000
1st line
2nd line
2nd line
IR Signal Amplitude
6
4
3
100
2
1
• DC light (e.g. from tungsten bulbs sunlight)
10
0
0
• Continuous signals at any frequency
5
15
20
Time (ms)
16920
• Strongly or weakly modulated patterns from fluorescent
lamps with electronic ballasts (see Fig. 13 or Fig. 14).
10
Fig. 13 - IR Disturbance from Fluorescent Lamp
With Low Modulation
Axis Title
10000
40
1000
0
1st line
2nd line
2nd line
IR Signal Amplitude
20
-20
100
-40
10
-60
0
5
10
15
20
Time (ms)
16921
Fig. 14 - IR Disturbance from Fluorescent Lamp
With High Modulation
TSOP331..
TSOP333..
TSOP335..
Minimum burst length
6 cycles/burst
6 cycles/burst
6 cycles/burst
After each burst of length
A gap time is required of
6 to 70 cycles
≥ 10 cycles
6 to 35 cycles
≥ 10 cycles
6 to 24 cycles
≥ 10 cycles
70 cycles
35 cycles
24 cycles
> 1.2 x burst length
> 6 x burst length
> 25 ms
2000
2000
2000
Yes
For bursts greater than
a minimum gap time in the data
stream is needed of
Maximum number of continuous
short bursts/second
MCIR code
Yes
Preferred
RCMM code
Yes
Preferred
Yes
XMP-1, XMP-2 code
Yes
Preferred
Yes
Mild disturbance patterns
are suppressed (example:
signal pattern of Fig. 13)
Complex disturbance patterns
are suppressed (example: signal
pattern of Fig. 14)
Critical disturbance patterns
are suppressed,
e.g. highly dimmed LCDs
Suppression of interference from
fluorescent lamps
Note
• For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP332.., TSOP334..
Rev. 1.6, 05-Aug-2021
5
Document Number: 82742
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP331.., TSOP333.., TSOP335..
www.vishay.com
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
5
Cavity number
Marking area
5.4
R2.5
15.2 ± 0.3
(0.95)
(5.05)
7.6
6.35
2.25
(1.1)
(3 x) 0.85 max.
0.95
1
2
3
(3 x) 0.6 ± 0.1
(3 x)
0.3 ± 0.1
2.54 nom.
2.54 nom.
Technical drawings
according to DIN
specifications
R2.5
Not indicated tolerances ± 0.2
Drawing-No.: 6.550-5335.01-4
Issue: 2; 02.07.19
Rev. 1.6, 05-Aug-2021
6
Document Number: 82742
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP331.., TSOP333.., TSOP335..
www.vishay.com
Vishay Semiconductors
BULK PACKAGING
Standard shipping for minimold is in conductive plastic bags. The packing quantity is determined by weight and a maximum of
0.3 % of the components per carton may be missing.
ORDERING INFORMATION
T
S
P
O = receiver
S = sensor
d
d
IC and
package type
d
AGC
d
d
Frequency
Note
• d = “digit”, please consult the list of available series on the previous page to create a valid part number
Examples: TSOP33338
TSOP33356VI1
TSOP33338SS1F
PACKAGING QUANTITY
• 300 pieces per bag (each bag is individually boxed)
• 6 bags per carton
Rev. 1.6, 05-Aug-2021
7
Document Number: 82742
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 01-Jan-2022
1
Document Number: 91000