TSOP6130TR

Datasheet Values Refer to PCN-OPT-1224-2022 TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems DESCRIPTION This IR receiver series is optimized for short burst remote control systems in different environments. The customer can chose between different IC settings (AGC variants), to find the optimum solution for his application. The higher the AGC, the better noise is suppressed, but the lower the code compatibility. The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. These components have not been qualified to automotive specifications. 23204 FEATURES • Individual IC settings to reach maximum performance • Immunity against noise (lamps, LCD TV, Wi-Fi) • Low supply current • Photo detector and preamplifier in one package • Supply voltage: 2.0 V to 5.5 V • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 LINKS TO ADDITIONAL RESOURCES Product Page Marking APPLICATIONS • Infrared remote control systems DESIGN SUPPORT TOOLS • 3D models • Window size calculator BLOCK DIAGRAM 3 33 kΩ VS 4 Input AGC Band pass Demodulator OUT 1 PIN Control circuit GND 16838-1 Rev. 1.8, 16-Aug-2022 1 Document Number: 82457 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1224-2022 TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors MECHANICAL DATA ORDERING CODE Pinning 1 = GND, 2 = N.C., 3 = VS, 4 = OUT Taping: TSOP6...TT - top view taped, 1190 pcs/reel TSOP6...TR - side view taped, 1120 pcs/reel APPLICATION CIRCUIT 17170-14 R1 Transmitter with TSALxxxx IR receiver VS Circuit 1 2 + VS C1 µC OUT VO 3 4 GND 23205 GND R1 and C1 recommended in case there are strong ripple or spikes on the supply line. PARTS TABLE LEGACY, FOR SHORT BURST REMOTE CONTROLS (AGC1) NOISY ENVIRONMENTS AND SHORT BURSTS (AGC3) VERY NOISY ENVIRONMENTS AND SHORT BURSTS (AGC5) 30 kHz TSOP6130 TSOP6330 TSOP6530 33 kHz TSOP6133 TSOP6333 TSOP6533 36 kHz TSOP6136 TSOP6336 (1)(2) TSOP6536 38 kHz TSOP6138 TSOP6338 (3)(5) TSOP6538 40 kHz TSOP6140 TSOP6340 TSOP6540 56 kHz TSOP6156 TSOP6356 (4) TSOP6556 AGC Carrier frequency Package Panhead Pinning 1 = GND, 2 = N.C., 3 = VS, 4 = OUT Dimensions (mm) 7.5 W x 5.3 H x 4.0 D Mounting SMD Application Remote control Best choice for (1) Special options • Narrow optical filter: www.vishay.com/doc?81590 • Wide optical flter: www.vishay.com/doc?82726 MCIR (2) RCMM (3) RECS-80 Code (4) r-map (5) XMP ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL VALUE Supply voltage TEST CONDITION VS -0.3 to +6 V Supply current IS 5 mA Output voltage VO -0.3 to (VS + 0.3) V Output current IO 5 mA Junction temperature Storage temperature range Operating temperature range Power consumption Tamb ≤ 85 °C UNIT Tj 100 °C Tstg -25 to +85 °C Tamb -25 to +85 °C Ptot 10 mW Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability Rev. 1.8, 16-Aug-2022 2 Document Number: 82457 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1224-2022 TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT VS 2.0 - 5.5 V Supply voltage VS = 3.3 V, Ev = 0 ISD 0.25 0.35 0.45 mA Ev = 40 klx, sunlight ISH - 0.45 - mA Ev = 0, IR diode TSAL6200, IF = 50 mA, test signal see Fig. 1 d - 18 - m IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 VOSL - - 100 mV Test signal: RC5 code Ee min. - 0.2 0.4 mW/m2 Test signal: XMP code Ee min. - 0.35 0.5 mW/m2 tpi - 3/fo < tpo < tpi + 3.5/fo, test signal see Fig. 1 Ee max. 30 - - W/m2 Angle of half transmission distance ϕ1/2 - ± 50 - deg Supply current Transmission distance Output voltage low Minimum irradiance Maximum irradiance Directivity TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Ee Optical Test Signal (IR diode TSAL6200, N = 6 pulses, f = f0, T = 10 ms) Ee Optical Test Signal t tpi (1) 600 µs T (1) t = 60 ms tpi ≥ 6/f0 Output Signal (2) (3) VOH 4/f0 < td < 10/f0 tpi - 3.0/f0 < tpo < tpi + 3.5/f0 94 8134 Output Signal, (see Fig. 4) VO VO VOH VOL VOL td t 600 µs (2) tpo t on t (3) t off t 14337-5 Fig. 1 - Output Active Low Fig. 3 - Output Function Axis Title Axis Title 10000 2nd line ton, toff - Output Pulse Width (ms) 0.25 1000 0.15 1st line 2nd line 2nd line tpo - Output Pulse Width (ms) Output pulse width 0.20 Input burst length 100 0.10 0.05 λ = 950 nm, optical test signal, Fig. 1 0 0.1 10 1000 10000 0.8 ton 0.7 0.6 1000 0.5 toff 1st line 2nd line 0.30 0.4 0.3 100 0.2 0.1 λ = 950 nm, optical test signal, Fig. 3 0 10 100 000 0.1 1 10 100 1000 Ee - Irradiance (mW/m2) Ee - Irradiance (mW/m2) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Fig. 4 - Output Pulse Diagram Rev. 1.8, 16-Aug-2022 3 10 10 000 Document Number: 82457 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1224-2022 TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors Axis Title 1.2 1.0 0.8 0.6 0.4 f = f0 ± 5 % f (3 dB) = f0/7 0.2 0.0 0.8 0.7 1000 AGC 1 0.6 1st line 2nd line 2nd line Maximum Envelope Duty Cycle 1.0 Ee min./Ee - Rel. Responsivity 10000 f = 38 kHz, Ee = 2 mW/m2 0.9 0.5 0.4 0.3 100 AGC3 0.2 0.1 0.7 0.9 16926 1.1 AGC 5 1.3 10 0 f/f0 - Relative Frequency 0 20 40 60 80 100 120 140 Burst Length (Number of Cycles/Burst) Fig. 5 - Frequency Dependence of Responsivity Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length Axis Title Axis Title 10000 3 1000 2 100 1 0 0.01 10 0.1 1 10 0.7 0.6 1000 0.5 1st line 2nd line Wavelength of ambient illumination: λ = 950 nm 2nd line Ee min. - Threshold Irradiance (mW/m2) Correlation with ambient light sources: 10 W/m2 = 1.4 klx (std. ilum. A, T = 2855 K) 10 W/m2 = 8.2 klx (daylight, T = 5900 K) 4 10000 0.8 1st line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) 5 0.4 0.3 100 0.2 0.1 10 0 -30 100 -10 10 50 70 90 Ee - Ambient DC Irradiance (W/m2) Tamb - Ambient Temperature (°C) Fig. 6 - Sensitivity in Bright Ambient Fig. 9 - Sensitivity vs. Ambient Temperature Axis Title Axis Title 10000 1.0 0.7 0.6 1000 0.5 0.4 0.3 1st line 2nd line f = f0 f = 30 kHz f = 10 kHz f = 100 Hz 100 0.2 0.1 0 1 10 100 10 1000 0.8 0.7 1000 0.6 0.5 0.4 100 0.3 0.2 0.1 0 750 ∆VS RMS - AC Voltage on DC Supply Voltage (mV) 21425 Fig. 7 - Sensitivity vs. Supply Voltage Disturbances Rev. 1.8, 16-Aug-2022 10000 0.9 1st line 2nd line 2nd line S(λ)rel. - Relative Spectral Sensitivity 0.8 2nd line Ee min. - Threshold Irradiance (mW/m2) 30 850 950 1050 10 1150 λ - Wavelength (nm) Fig. 10 - Relative Spectral Sensitivity vs. Wavelength 4 Document Number: 82457 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1224-2022 TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors Axis Title 10° 20° 2nd line Ee min. - Threshold Irradiance (mW/m2) 30° 40° 1.0 0.9 50° 0.8 60° 70° 0.7 80° 0.6 16801 0.4 0.2 0 0.2 0.4 0.7 0.6 1000 0.5 0.4 0.3 100 0.2 0.1 10 0 0.6 1 d rel - Relative Transmission Distance 2 3 4 5 6 VS - Supply Voltage (V) Fig. 11 - Horizontal Directivity Rev. 1.8, 16-Aug-2022 10000 0.8 1st line 2nd line 0° Fig. 12 - Sensitivity vs. Supply Voltage 5 Document Number: 82457 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1224-2022 TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT Axis Title This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device’s band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. When a data signal is applied to the product in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the receiver’s output. Some examples which are suppressed are: • DC light (e.g. from tungsten bulbs sunlight) • Continuous signals at any frequency • Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig. 13 or Fig. 14) • 2.4 GHz and 5 GHz Wi-Fi 10000 7 5 1000 1st line 2nd line 2nd line IR Signal Amplitude 6 4 3 100 2 1 10 0 0 5 10 15 20 Time (ms) 16920 Fig. 13 - IR Disturbance from Fluorescent Lamp With Low Modulation Axis Title 10000 40 1000 0 1st line 2nd line 2nd line IR Signal Amplitude 20 -20 100 -40 10 -60 0 5 10 15 20 Time (ms) 16921 Fig. 14 - IR Disturbance from Fluorescent Lamp With High Modulation TSOP61.. TSOP63.. TSOP65.. Minimum burst length 6 cycles/burst 6 cycles/burst 6 cycles/burst After each burst of length A gap time is required of 6 to 68 cycles ≥ 6 cycles 6 to 40 cycles ≥ 7 cycles 6 to 20 cycles ≥ 7 cycles For bursts greater than a minimum gap time in the data stream is needed of 68 cycles 40 cycles 20 cycles > 1 x burst length > 6 x burst length > 10 x burst length Maximum number of continuous short bursts/second 2500 2500 2500 RCMM code Yes Preferred Yes XMP code Yes Preferred Yes r-map code Yes Preferred Yes Mild disturbance patterns are suppressed (example: signal pattern of Fig. 13) Complex disturbance patterns are suppressed (example: signal pattern of Fig. 14) Critical disturbance patterns are suppressed, e.g. highly dimmed LCDs Suppression of interference from fluorescent lamps Note • For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP62.., TSOP64.. Rev. 1.8, 16-Aug-2022 6 Document Number: 82457 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1224-2022 TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 7.5 Pick and place area. TT taping 7.2 (1.5) 2.8 2.2 5.3 A 1 4 0.5 ± 0.15 0.1 (1.4) 0.3 4x 0.1 1.27 2.9 3 x 1.27 = 3.81 4 0.4 A 5.51 Not indicated tolerances ± 0.3 Pick and place area. TR taping technical drawings according to DIN specifications 2.6 Footprint 2.35 3 x 1.27 = 3.81 0.9 2.2 1.27 R 1.7 Drawing-No.: 6.544-5341.01-4 Issue: 8; 02.09.09 16776 ASSEMBLY INSTRUCTIONS Reflow Soldering • Reflow soldering must be done within 72 h while stored under a max. temperature of 30 °C, 60 % RH after opening the dry pack envelope • Set the furnace temperatures for pre-heating and heating in accordance with the reflow temperature profile as shown in the diagram. Exercise extreme care to keep the maximum temperature below 260 °C. The temperature shown in the profile means the temperature at the device surface. Since there is a temperature difference between the component and the circuit board, it should be verified that the temperature of the device is accurately being measured • Handling after reflow should be done only after the work surface has been cooled off Rev. 1.8, 16-Aug-2022 Manual Soldering • Use a soldering iron of 25 W or less. Adjust the temperature of the soldering iron below 300 °C • Finish soldering within 3 s • Handle products only after the temperature has cooled off 7 Document Number: 82457 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1224-2022 TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE Axis Title 10000 300 max. 260 °C 255 °C 240 °C 245 °C 217 °C 1000 200 max. 20 s 1st line 2nd line 2nd line Temperature (°C) 250 150 max. 120 s max. 100 s 100 100 Max. ramp up 3 °C/s 50 Max. ramp down 6 °C/s Max. 2 cycles allowed 10 0 0 19800 50 100 150 200 250 300 Time (s) TAPING VERSION TSOP..TT DIMENSIONS in millimeters 16584 Rev. 1.8, 16-Aug-2022 8 Document Number: 82457 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1224-2022 TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR DIMENSIONS in millimeters 16585 Rev. 1.8, 16-Aug-2022 9 Document Number: 82457 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1224-2022 TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors REEL DIMENSIONS in millimeters 16734 LEADER AND TRAILER DIMENSIONS in millimeters Trailer no devices Leader devices no devices End Start min. 200 min. 400 96 11818 Rev. 1.8, 16-Aug-2022 10 Document Number: 82457 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1224-2022 TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors OUTER PACKAGING The sealed reel is packed into a pizza box. CARTON BOX DIMENSIONS in millimeters Length Thickness 22127 Width THICKNESS WIDTH LENGTH 50 340 340 Pizza box (SMD and Heimdall) (taping in reels) COVER TAPE PEEL STRENGTH LABEL According to DIN EN 60286-3 0.1 N to 1.3 N 300 ± 10 mm/min. 165° to 180° peel angle Standard bar code labels for finished goods The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data. VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods) PLAIN WRITING Item-description ABBREVIATION LENGTH - 18 Item-number INO 8 Selection-code SEL 3 LOT-/serial-number BATCH 10 COD 3 (YWW) Plant-code PTC 2 Quantity QTY 8 Accepted by ACC - PCK - Data-code Packed by Mixed code indicator Origin LONG BAR CODE TOP MIXED CODE - xxxxxxx+ Company logo TYPE LENGTH Item-number N 8 Plant-code N 2 Sequence-number X 3 Quantity N 8 Total length - 21 TYPE LENGTH Selection-code X 3 Data-code N 3 Batch-number X 10 Filter - 1 Total length - 17 SHORT BAR CODE BOTTOM Rev. 1.8, 16-Aug-2022 11 Document Number: 82457 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1224-2022 TSOP61.., TSOP63.., TSOP65.. www.vishay.com Vishay Semiconductors DRY PACKING The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. LEVEL CAUTION This bag contains MOISTURE-SENSITIVE DEVICES Aluminum bag 4 1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relative humidity (RH) 2. After this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 °C) must be 2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or 2b. Stored at < 5 % RH Label 3. Devices require baking befor mounting if: Humidity Indicator Card is > 10 % when read at 23 °C ± 5 °C or 2a. or 2b. are not met. 4. If baking is required, devices may be baked for: 192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or 96 hours at 60 °C ± 5 °C and < 5 % RH for all device containers or 24 hours at 125 °C ± 5 °C not suitable for reels or tubes Reel Bag Seal Date: (If blank, see barcode label) 15973 Note: Level and body temperature defined by EIA JEDEC Standard J-STD-020 22522 FINAL PACKING EIA JEDEC standard J-STD-020 level 4 label is included on all dry bags The sealed reel is packed into a cardboard box. ESD PRECAUTION RECOMMENDED METHOF OF STORAGE Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electrostatic sensitive devices warning labels are on the packaging. Dry box storage is recommended as soon as the aluminum bag has been opened to prevent moisture absorption. The following conditions should be observed, if dry boxes are not available: • Storage temperature 10 °C to 30 °C • Storage humidity ≤ 60 % RH max. After more than 72 h under these conditions moisture content will be too high for reflow soldering. In case of moisture absorption, the devices will recover to the former condition by drying under the following condition: 192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air / nitrogen) or 96 h at 60 °C + 5 °C and < 5 % RH for all device containers or 24 h at 125 °C + 5 °C not suitable for reel or tubes. An EIA JEDEC® standard J-STD-020 level 4 label is included on all dry bags. VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS The Vishay Semiconductors standard bar code labels are printed at final packing areas. The labels are on each packing unit and contain Vishay Semiconductors specific data. 22645 Rev. 1.8, 16-Aug-2022 12 Document Number: 82457 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000