TSOP75238WTR

TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES • Very low supply current • Photo detector and preamplifier in one package • Internal filter for PCM frequency • Supply voltage: 2.5 V to 5.5 V • Improved immunity against ambient light • Capable of side or top view • Low profile 2.35 mm • Insensitive to supply voltage ripple and noise • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 MECHANICAL DATA LINKS TO ADDITIONAL RESOURCES Pinning: 3D 3D Product Page 3D Models 1, 4 = GND, 2 = VS, 3 = OUT Calculators Marking ORDERING CODE DESCRIPTION Taping: The TSOP75...W series are miniaturized SMD IR receiver modules for infrared remote control systems. Two PIN diodes and a preamplifier are assembled on a leadframe, the epoxy package contains an IR filter. TSOP75...WTT - top view taped, 2200 pcs/reel The demodulated output signal can be directly connected to a microprocessor for decoding. BLOCK DIAGRAM TSOP75...WTR - side view taped, 2300 pcs/reel 2 The TSOP754..W series devices are optimized to suppress almost all spurious pulses from energy saving lamps like CFLs. The AGC4 used in the TSOP754..W may suppress some data signals. The TSOP752..W series are provided primarily for compatibility with old AGC2 designs. New designs should prefer the TSOP754..W series containing the newer AGC4. 30 k Ω VS 3 Input Band pass AGC OUT Demodulator 1, 4 PIN These components have not been qualified according to automotive specifications. GND Control circuit 20445-1 APPLICATION CIRCUIT 17170-11 R1 IR receiver VS Circuit Transmitter with TSALxxxx + VS C1 μC OUT GND VO GND R1 and C1 recommended to reduce supply ripple for VS < 2.8 V Rev. 2.2, 29-Mar-2021 1 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors PARTS TABLE LEGACY, FOR LONG BURST REMOTE CONTROLS (AGC2) RECOMMENDED FOR LONG BURST CODES (AGC4) 30 kHz TSOP75230W TSOP75430W 33 kHz TSOP75233W TSOP75433W 36 kHz TSOP75236W TSOP75436W (1)(2)(3) 38 kHz TSOP75238W TSOP75438W (4)(5) 40 kHz TSOP75240W TSOP75440W 56 kHz TSOP75256W TSOP75456W (6)(7) AGC Carrier frequency Package Heimdall no lens Pinning 1, 4 = GND, 2 = VS, 3 = OUT Dimensions (mm) 6.8 W x 3.0 H x 2.35 D Mounting SMD Application Remote control (1) Best choice for Special options RC-5 (2) RC-6 (3) Panasonic (4) NEC (5) Sharp (6) r-step (7) Thomson RCA • Extended temperature range: www.vishay.com/doc?82738 • Narrow optical filter: www.vishay.com/doc?81590 • Wide optical flter: www.vishay.com/doc?82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT VS -0.3 to +6 V mA Supply voltage Supply current IS 3 Output voltage VO -0.3 to (VS + 0.3) V Output current IO 5 mA Junction temperature Tj 100 °C Storage temperature range Tstg -25 to +85 °C Operating temperature range Tamb -25 to +85 °C Ptot 10 mW Power consumption Tamb ≤ 85 °C Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. VS 2.5 - 5.5 V Ev = 0, VS = 3.3 V ISD 0.27 0.35 0.45 mA Ev = 40 klx, sunlight ISH - 0.45 - mA Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA d - 16 - m VOSL - - 100 mV Supply voltage Supply current Transmission distance Output voltage low mW/m2, IOSL = 0.5 mA, Ee = 0.7 test signal see Fig. 1 UNIT Minimum irradiance Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1 Ee min. - 0.25 0.5 mW/m2 Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1 Ee max. 30 - - W/m2 Directivity Angle of half transmission distance ϕ1/2 - ± 75 - ° Rev. 2.2, 29-Mar-2021 2 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Optical Test Signal Ee 0.8 Ton, Toff - Output Pulse Width (ms) (IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms) t tpi * T 10/f0 is recommended for optimal function * tpi Output Signal VO 1) VOH 2) 16110 7/f0 < td < 15/f0 tpi - 5/f0 < tpo < tpi + 6/f0 Ton 0.7 0.6 0.5 Toff 0.4 0.3 λ = 950 nm, Optical Test Signal, Fig. 3 0.2 0.1 0 0.1 VOL td 1) tpo 2) t 21584 103 104 105 1.2 Output Pulse Width 0.9 Ee min./Ee - Relative Responsivity tpo - Output Pulse Width (ms) 102 Fig. 4 - Output Pulse Diagram 1.0 0.8 Input Burst Length 0.7 0.6 0.5 0.4 0.3 λ = 950 nm, Optical Test Signal, Fig.1 0.2 0.1 1.0 0.8 0.6 0.4 f = f0 ± 5 % Δf(3 dB) = f0/10 0.2 0.0 0 0.1 1 10 102 103 104 105 0.7 Ee - Irradiance (mW/m²) 21583 Ee min. - Threshold Irradiance (mW/m²) t 600 µs t = 60 ms 94 8134 Output Signal, (see Fig. 4) VOH VOL t on t off 1.3 4 Correlation with Ambient Light Sources: 3.5 10 W/m² = 1.4 kLx (Std. illum. A, T = 2855 K) 10 W/m² = 8.2 kLx (Daylight, T = 5900 K) 3 2.5 2 1.5 Wavelength of Ambient Illumination: λ = 950 nm 1 0.5 0 0.01 t 21585 0.1 1 10 100 Ee - Ambient DC Irradiance (W/m²) Fig. 6 - Sensitivity in Bright Ambient Fig. 3 - Output Function Rev. 2.2, 29-Mar-2021 1.1 Fig. 5 - Frequency Dependence of Responsivity Optical Test Signal 600 µs 0.9 f/f0 - Relative Frequency 16925 Fig. 2 - Pulse Length and Sensitivity in Dark Ambient VO 10 Ee - Irradiance (mW/m²) Fig. 1 - Output Active Low Ee 1 3 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors Axis Title 1.0 2.5 f = f0 f = 30 kHz f = 10 kHz f = 100 Hz 2.0 1.5 1.0 0.5 0 1 10 100 1000 10000 0.9 0.8 0.7 1000 0.6 1st line 2nd line 2nd line S(λ)rel. - Relative Spectral Sensitivity Ee min. - Threshold Irradiance (mW/m2) 3.0 0.5 0.4 100 0.3 0.2 0.1 750 850 950 Fig. 10 - Relative Spectral Sensitivity vs. Wavelength Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 1.0 0° d rel - Relative Transmission Distance Max. Envelope Duty Cycle 0.9 0.8 0.7 0.6 0.5 TSOP752..W 0.3 TSOP754..W 0.2 0.1 f = 38 kHz, Ee = 2 mW/m² 0 0 21588 20 40 60 80 100 120 50° 60° 0.8 70° 80° 0.7 0.6 0.4 0.2 0 Fig. 11 - Horizontal Directivity d rel - Relative Transmission Distance 0° 0.5 0.4 0.3 0.2 0.1 0 -10 10 30 50 70 10° 20° 30° 40° 1.0 0.9 50° 0.8 60° 70° 0.7 80° 90 21580 Tamb - Ambient Temperature (°C) 0.6 0.4 0.2 0 Fig. 12 - Vertical Directivity Fig. 9 - Sensitivity vs. Ambient Temperature Rev. 2.2, 29-Mar-2021 30° 0.9 0.6 -30 20° 1.0 21581 Burst Length (number of cycles/burst) 10° 40° Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length Ee min. - Threshold Irradiance (mW/m2) 1050 λ - Wavelength (nm) 21425 0.4 10 1150 0 ΔVS RMS - AC Voltage on DC Supply Voltage (mV) 4 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors Ee min. - Sensitivity (mW/m2) 0.60 0.50 0.40 0.30 0.20 0.10 0.00 1 2 3 4 5 VS - Supply Voltage (V) Fig. 13 - Sensitivity vs. Supply Voltage Rev. 2.2, 29-Mar-2021 5 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT Axis Title This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device’s band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. 10000 7 6 When a data signal is applied to the product in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the receiver’s output. 1000 1st line 2nd line 2nd line IR Signal Amplitude 5 4 3 100 2 1 Some examples which are suppressed are: 10 0 • DC light (e.g. from tungsten bulbs sunlight) 0 • Continuous signals at any frequency 5 10 15 20 Time (ms) 16920 • Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig. 14 or Fig. 15) Fig. 14 - IR Disturbance from Fluorescent Lamp With Low Modulation Axis Title 10000 40 1000 0 1st line 2nd line 2nd line IR Signal Amplitude 20 -20 100 -40 10 -60 0 5 10 15 20 Time (ms) 16921 Fig. 15 - IR Disturbance from Fluorescent Lamp With High Modulation TSOP752..W TSOP754..W Minimum burst length 10 cycles/burst 10 cycles/burst After each burst of length a minimum gap time is required of 10 to 70 cycles ≥ 10 cycles 10 to 35 cycles ≥ 10 cycles For bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 4 x burst length 35 cycles > 10 x burst length Maximum number of continuous short bursts/second 1800 1500 NEC code Yes Preferred RC5 / RC6 code Yes Preferred Thomson 56 kHz code Yes Preferred Sharp code Yes Preferred Mild disturbance patterns are suppressed (example: signal pattern of Fig. 14) Complex and critical disturbance patterns are suppressed (example: signal pattern of Fig. 15 or highly dimmed LCDs) Suppression of interference from fluorescent lamps Notes • For data formats with short bursts please see the datasheet for TSOP753..W • For Sony 12, 15, and 20 bit IR codes please see the datasheet of TSOP75S40FW Rev. 2.2, 29-Mar-2021 6 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 6.8 6.6 ± 0.1 Center of sensitive area (3.25) Mold residue 2.35 (1.8) 1.2 ± 0.2 3 0.8 Mold residue (0.635) (1) 1.27 (3 x) 0.5 ± 0.1 (4 x) technical drawings according to DIN specifications 3 x 1.27 = 3.81 Marking area 2.05 Not indicated tolerances ± 0.15 (1.5) Tool separation line (2.2) Proposed pad layout from component side (for reference only) 3 x 1.27 = 3.81 Pick and place area 1.8 1.27 Drawing-No.: 6.550-5300.01-4 Issue: 4; 13.09.11 0.8 22609 ASSEMBLY INSTRUCTIONS Reflow Soldering Manual Soldering • Reflow soldering must be done within 72 h while stored under a max. temperature of 30 °C, 60 % RH after opening the dry pack envelope • Use a soldering iron of 25 W or less. Adjust the temperature of the soldering iron below 300 °C • Set the furnace temperatures for pre-heating and heating in accordance with the reflow temperature profile as shown in the diagram. Exercise extreme care to keep the maximum temperature below 260 °C. The temperature shown in the profile means the temperature at the device surface. Since there is a temperature difference between the component and the circuit board, it should be verified that the temperature of the device is accurately being measured • Handle products only after the temperature has cooled off • Finish soldering within 3 s • Handling after reflow should be done only after the work surface has been cooled off Rev. 2.2, 29-Mar-2021 7 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE max. 260 °C 255 °C 240 °C 2nd line Temperature (°C) 250 245 °C 217 °C 1000 200 max. 20 s 150 max. 120 s max. 100 s 100 100 Max. ramp up 3 °C/s 50 Max. ramp down 6 °C/s Max. 2 cycles allowed 10 0 50 0 100 150 200 250 300 Time (s) 19800 3.6 0.3 TAPING VERSION TSOP..TR DIMENSIONS in millimeters 16 1.75 7.5 Ø 1.5 4 Direction of feed 8 2 Ø 1.5 technical drawings according to DIN specifications Drawing-No.: 9.700-5342.01-4 Issue: 2; 12.06.13 Rev. 2.2, 29-Mar-2021 8 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors 3 0.3 TAPING VERSION TSOP..TT DIMENSIONS in millimeters 16 1.75 7.5 Ø 1.5 4 Direction of feed 8 2 Ø 1.5 min. technical drawings according to DIN specifications Drawing-No.: 9.700-5341.01-4 Issue: 3; 06.10.15 Rev. 2.2, 29-Mar-2021 9 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors REEL DIMENSIONS in millimeters 16734 LEADER AND TRAILER DIMENSIONS in millimeters Trailer no devices Leader devices no devices End Start min. 200 min. 400 96 11818 COVER TAPE PEEL STRENGTH According to DIN EN 60286-3 0.1 N to 1.3 N 300 ± 10 mm/min. 165° to 180° peel angle Rev. 2.2, 29-Mar-2021 10 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors OUTER PACKAGING The sealed reel is packed into a pizza box. CARTON BOX DIMENSIONS in millimeters Length Thickness Width 22127 Pizza box (SMD and heimdall) (taping in reels) THICKNESS WIDTH LENGTH 50 340 340 LABEL Standard bar code labels for finished goods The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data. VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods) PLAIN WRITING ABBREVIATION LENGTH Item-description - 18 INO 8 Item-number Selection-code SEL 3 BATCH 10 Data-code COD 3 (YWW) Plant-code PTC 2 Quantity QTY 8 Accepted by ACC - Packed by PCK - MIXED CODE - xxxxxxx+ Company logo TYPE LENGTH LOT-/serial-number Mixed code indicator Origin LONG BAR CODE TOP Item-number N 8 Plant-code N 2 Sequence-number X 3 Quantity N 8 Total length - 21 SHORT BAR CODE BOTTOM TYPE LENGTH Selection-code X 3 Data-code N 3 Batch-number X 10 Filter - 1 Total length - 17 Rev. 2.2, 29-Mar-2021 11 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors DRY PACKING ESD PRECAUTION The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electrostatic sensitive devices warning labels are on the packaging. Aluminum bag VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS Label The Vishay Semiconductors standard bar code labels are printed at final packing areas. The labels are on each packing unit and contain Vishay Semiconductors specific data. Reel 15973 FINAL PACKING The sealed reel is packed into a cardboard box. RECOMMENDED METHOD OF STORAGE 22178 Dry box storage is recommended as soon as the aluminum bag has been opened to prevent moisture absorption. The following conditions should be observed, if dry boxes are not available: • Storage temperature 10 °C to 30 °C • Storage humidity ≤ 60 % RH max. After more than 72 h under these conditions moisture content will be too high for reflow soldering. In case of moisture absorption, the devices will recover to the former condition by drying under the following condition: 192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air / nitrogen) or 96 h at 60 °C + 5 °C and < 5 % RH for all device containers or 24 h at 125 °C + 5 °C not suitable for reel or tubes. An EIA JEDEC® standard J-STD-020 level 4 label is included on all dry bags. CAUTION This bag contains MOISTURE-SENSITIVE DEVICES LEVEL 4 1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relative humidity (RH) 2. After this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 °C) must be 2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or 2b. Stored at < 5 % RH 3. Devices require baking befor mounting if: Humidity Indicator Card is > 10 % when read at 23 °C ± 5 °C or 2a. or 2b. are not met. 4. If baking is required, devices may be baked for: 192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or 96 hours at 60 °C ± 5 °C and < 5 % RH for all device containers or 24 hours at 125 °C ± 5 °C not suitable for reels or tubes Bag Seal Date: (If blank, see barcode label) Note: Level and body temperature defined by EIA JEDEC Standard J-STD-020 22522 EIA JEDEC standard J-STD-020 level 4 label is included on all dry bags Rev. 2.2, 29-Mar-2021 12 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000