TSOP936..
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Improved dark sensitivity
• Improved immunity against optical noise
• Very low supply current
•
•
•
•
•
Photo detector and preamplifier in one package
Internal filter for PCM frequency
Supply voltage: 2.0 V to 3.6 V
Insensitive to supply voltage ripple and noise
Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
23051
LINKS TO ADDITIONAL RESOURCES
MECHANICAL DATA
3D 3D
Product Page
3D Models
1 = OUT, 2 = GND, 3 = VS
Calculators
Marking
Packages
ORDERING CODE
TSOP936.. - 1800 pieces in bags
Bends and Cuts
BLOCK DIAGRAM
DESCRIPTION
16833-13
The TSOP93... series devices are the latest generation
miniaturized IR receiver modules for infrared remote control
systems. These series provide improvements in sensitivity
to remote control signals in dark ambient as well as in
sensitivity in the presence of optical disturbances e.g. from
CFLs.
3
30 kΩ
1
Input
The devices contain a PIN diode and a preamplifier
assembled on a lead frame. The epoxy package contains an
IR filter. The demodulated output signal can be directly
connected to a microprocessor for decoding.
Band
pass
AGC
Demodulator
2
PIN
The TSOP936.., series devices are designed to receive long
burst codes (10 or more carrier cycles per burst). The third
digit designates the AGC level (AGC6) and the last two digits
designate the band-pass frequency (see table below). The
higher the AGC, the better noise is suppressed, but the
lower the code compatibility. AGC6 provides maximized
noise suppression. Generally, we advise to select the
highest AGC that satisfactorily receives the desired remote
code.
Control circuit
APPLICATION CIRCUIT
17170-12
Transmitter
with
TSALxxxx
These components have not been qualified to automotive
specifications.
R1
IR receiver
VS
Circuit
Holders
+ VS
C1
μC
OUT
GND
VO
GND
R1 and C1 recommended to reduce supply ripple for VS < 2.2 V
Rev. 1.3, 30-Jul-2021
1
Document Number: 82842
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP936..
www.vishay.com
Vishay Semiconductors
PARTS TABLE
MAXIMIZED NOISE SUPPRESSION
(AGC6)
AGC
30 kHz
Carrier frequency
TSOP93630
33 kHz
TSOP93633
36 kHz
TSOP93636 (5)(6)
38 kHz
TSOP93638 (3)(4)(11)
40 kHz
TSOP93640
56 kHz
TSOP93656
Package
Minimold
Pinning
1 = OUT, 2 = GND, 3 = VS
Dimensions (mm)
5.4 W x 6.35 H x 4.9 D
Mounting
Leaded
Application
Remote control
(1)
Best choice for
Special options
Cisco
(2) MCIR (3) Mitsubishi (4) NEC (5) Panasonic (6) RC-5 (7)
(8) RCA (9) r-step (10) Sejin 4PPM (11) Sharp (12) Sony
RC-6
• Narrow optical filter: www.vishay.com/doc?81590
• Wide optical flter: www.vishay.com/doc?82726
Notes
• 30 kHz and 33 kHz only available on written request
• See datasheet for TSOP932.., TSOP934.. for preferred devices for (1)(2)(7)(8)(9)(10)(12)
ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
VALUE
Supply voltage
TEST CONDITION
VS
-0.3 to +3.6
V
Supply current
IS
3
mA
Output voltage
VO
-0.3 to (VS + 0.3)
V
Output current
IO
5
mA
Junction temperature
UNIT
Tj
100
°C
Storage temperature range
Tstg
-25 to +85
°C
Operating temperature range
Tamb
-25 to +85
°C
Power consumption
Soldering temperature
Tamb ≤ 85 °C
Ptot
10
mW
t ≤ 10 s, 1 mm from case
Tsd
260
°C
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
Supply current
TEST CONDITION
SYMBOL
MIN.
Ev = 0, VS = 3.3 V
ISD
Ev = 40 klx, sunlight
ISH
Supply voltage
TYP.
MAX.
UNIT
0.25
0.37
0.45
mA
-
0.50
-
mA
VS
2.0
-
3.6
V
Transmission distance
Ev = 0, test signal see Fig. 1,
IR diode TSAL6200, IF = 50 mA
d
-
32
-
m
Output voltage low
IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see Fig. 1
VOSL
-
-
100
mV
Minimum irradiance
Test signal: NEC code
Ee min.
-
0.07
0.15
mW/m2
Maximum irradiance
tpi - 5/f0 < tpo < tpi + 6/f0,
test signal see Fig. 1
Ee max.
30
-
-
W/m2
Directivity
Angle of half transmission
distance
ϕ1/2
-
± 45
-
°
Rev. 1.3, 30-Jul-2021
2
Document Number: 82842
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP936..
www.vishay.com
Vishay Semiconductors
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Axis Title
Optical Test Signal
(IR diode TSAL6200, 30 pulses, f = f0, T = 15 ms)
(1)
(1)
T
tpi ≥ 10/f0
Output Signal
(2)
7/f0 < td < 15/f0
VO
(3)
VOH
16110-11
tpi - 5/f0 < tpo < tpi + 6/f0
ton
0.8
0.7
1000
0.6
toff
0.5
1st line
2nd line
t
tpi
10000
0.9
2nd line
ton, toff - Output Pulse Width (ms)
Ee
0.4
100
0.3
0.2
λ = 950 nm,
optical test signal, Fig. 3
0.1
10
10 000 100 000
0
VOL
td (2)
tpo (3)
0.1
t
1
10
100
1000
Ee - Irradiance (mW/m2)
Fig. 4 - Pulse-Width vs. Irradiance in Dark Ambient
Fig. 1 - Output Delay and Pulse-Width
Axis Title
Axis Title
10000
0.90
10000
1.2
1000
0.75
1st line
2nd line
0.80
Input burst length
100
0.70
0.65
λ = 950 nm,
optical test signal, Fig. 1
10
100 000
0.60
0.1
1000
1000
0.8
0.6
100
0.4
f = f0 ± 5 %
∆f (3 dB) = f0/10
0.2
10
0
0.7
0.9
1.1
1.3
Ee - Irradiance (mW/m2)
f/f0 - Relative Frequency
Fig. 2 - Pulse-Width vs. Irradiance in Dark Ambient
Fig. 5 - Frequency Dependence of Responsivity
Axis Title
Optical Test Signal
600 µs
4
t
600 µs
t = 60 ms
VO
1.0
94 8134
Output Signal, (see Fig. 4)
VOH
VOL
t on
t off
3
Wavelength of ambient
illumination: λ = 950 nm
1000
2
100
1
0
0.01
t
10
0.1
1
10
100
Ee - Ambient DC Irradiance (W/m2)
Fig. 6 - Sensitivity in Bright Ambient
Fig. 3 - Test Signal
Rev. 1.3, 30-Jul-2021
10000
Correlation with ambient light sources:
10 W/m2 = 1.4 klx (std. ilum. A, T = 2855 K)
10 W/m2 = 8.2 klx (daylight, T = 5900 K)
1st line
2nd line
Ee
10
2nd line
Ee min. - Threshold Irradiance (mW/m2)
2nd line
tpo - Output Pulse Width (ms)
0.85
1st line
2nd line
2nd line
Ee min./Ee - Relative Responsivity
Output pulse width
3
Document Number: 82842
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP936..
www.vishay.com
Vishay Semiconductors
Axis Title
Axis Title
10000
1.0
0.8
f = f0
f = 30 kHz
f = 10 kHz
f = 100 Hz
0.7
0.6
0.5
1000
0.4
100
0.3
0.2
0.1
0
10
1
10
100
1000
∆VS RMS - AC Voltage on DC Supply Voltage (mV)
10000
0.9
0.8
0.7
1000
0.6
1st line
2nd line
2nd line
S(λ)rel. - Relative Spectral Sensitivity
0.9
1st line
2nd line
0.5
0.4
100
0.3
0.2
0.1
0
750
850
950
Fig. 10 - Relative Spectral Sensitivity vs. Wavelength
Axis Title
Axis0°
Title 10°
20°
30°
10000
f = 38 kHz, Ee = 2 mW/m2
18
16
14
12
8
2nd line
2nd line
10
40°
1.0
1000
1st line
2nd line
2nd line
Minimum Burst Repetition Time (ms)
20
10
1150
λ - Wavelength (nm)
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
0.9
50°
0.8
60°
100
6
70°
0.7
4
80°
2
10
0
0
50
100
150
200
250
0.6
300
0.4
0.2
0.16
0.14
1000
1st line
2nd line
0.12
0.10
0.08
100
0.06
0.04
0.02
50
70
0.25
1000
0.20
0.15
100
0.10
0.05
10
0
10
0
10000
1st line
2nd line
2nd line
Ee min. - Threshold Irradiance (mW/m2)
0.18
30
0.6
0.30
10000
10
0.4
Axis Title
Axis Title
0.20
-10
0.2
Fig. 11 - Directivity
Fig. 8 - Minimum Burst Repetition Time vs. Burst Length
-30
0
drel. - Relative Transmission Distance
Burst Length (Number of Cycles/Burst)
2nd line
Ee min. - Threshold Irradiance (mW/m2)
1050
2nd line
2nd line
2nd line
Ee min. - Threshold Irradiance (mW/m2)
1.0
90
1.0
1.5
2.0
2.5
3.0
3.5
4.0
Tamb - Ambient Temperature (°C)
VS - Supply Voltage (V)
Fig. 9 - Sensitivity vs. Ambient Temperature
Fig. 12 - Sensitivity vs. Supply Voltage
Rev. 1.3, 30-Jul-2021
4
Document Number: 82842
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP936..
www.vishay.com
Vishay Semiconductors
SUITABLE DATA FORMAT
Axis Title
This series is designed to suppress spurious output pulses
due to noise or disturbance signals. The devices can
distinguish data signals from noise due to differences in
frequency, burst length, and envelope duty cycle. The data
signal should be close to the device’s band-pass center
frequency (e.g. 38 kHz) and fulfill the conditions in the table
below.
10000
7
When a data signal is applied to the product in the presence
of a disturbance, the sensitivity of the receiver is
automatically reduced by the AGC to insure that no spurious
pulses are present at the receiver’s output. Some examples
which are suppressed are:
5
1000
1st line
2nd line
2nd line
IR Signal Amplitude
6
4
3
100
2
1
• DC light (e.g. from tungsten bulbs sunlight)
10
0
0
• Continuous signals at any frequency
5
10
20
Time (ms)
16920
• Strongly or weakly modulated patterns from fluorescent
lamps with electronic ballasts (see Fig. 13 or Fig. 14)
15
Fig. 13 - IR Emission from Fluorescent Lamp
With Low Modulation
Axis Title
10000
40
1000
0
1st line
2nd line
2nd line
IR Signal Amplitude
20
-20
100
-40
10
-60
0
5
10
15
20
Time (ms)
16921
Fig. 14 - IR Emission from Fluorescent Lamp
With High Modulation
TSOP936..
Minimum burst length
10 cycles/burst
≥ 13 cycles
Minimum gap time between bursts
Minimum idle period between data frames
12 ms
RC-5 code
Preferred
RC-6 code
Yes
NEC code
Preferred
r-step code 56 kHz
Yes
Sony code
No
RCA 56 kHz code
Yes
Mitsubishi code 38 kHz
Preferred
Suppression of interference from fluorescent lamps
Fig. 13 and Fig. 14
Note
• For data formats with short bursts please see the datasheet for TSOP933.., TSOP935..
Rev. 1.3, 30-Jul-2021
5
Document Number: 82842
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP936..
www.vishay.com
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
5
Cavity number
Marking area
5.4
R2.5
15.2 ± 0.3
(0.95)
(5.05)
7.6
6.35
2.25
(1.1)
(3 x) 0.85 max.
0.95
1
2
3
(3 x) 0.6 ± 0.1
(3 x)
0.3 ± 0.1
2.54 nom.
2.54 nom.
Technical drawings
according to DIN
specifications
R2.5
Not indicated tolerances ± 0.2
Drawing-No.: 6.550-5335.01-4
Issue: 2; 02.07.19
Rev. 1.3, 30-Jul-2021
6
Document Number: 82842
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP936..
www.vishay.com
Vishay Semiconductors
BULK PACKAGING
Standard shipping for minimold is in conductive plastic bags. The packing quantity is determined by weight and the number of
components per carton may vary by a maximum of ± 0.3 %.
ORDERING INFORMATION
Examples: TSOP93638
TSOP93656VI1
TSOP93638SS1F
For more information, see: www.vishay.com/doc?80076
PACKAGING QUANTITY
• 300 pieces per bag (each bag is individually boxed)
• 6 bags per carton
Rev. 1.3, 30-Jul-2021
7
Document Number: 82842
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 09-Jul-2021
1
Document Number: 91000
