VCUT0714A-02Z-GS08

VCUT0714A-02Z Vishay Semiconductors Bidirectional Asymmetrical (BiAs) Single Line ESD-Protection Diode in SOD923 FEATURES • Tiny SOD-923 package • Package height < 0.4 mm 2 1 • Working range - 7 V up to + 14 V or - 14 V up to +7V • Low leakage current IR < 0.1 μA 20503 20516-1 • Low capacitance typical CD = 8 pF 1 • ESD-protection acc. IEC 61000-4-2 ± 25 kV contact discharge ± 30 kV air discharge MARKING (example only) XY • Working voltage range VRWM = 5 V • e3 - Sn 20279 Bar = pin 1 marking Y = type code (see table below) X = date code • Compliant to RoHS directive 2002/95/EC and in accordance to WEEE 2002/96/EC ORDERING INFORMATION ORDERING CODE TAPED UNITS PER REEL (8 mm TAPE ON 7" REEL) MINIMUM ORDER QUANTITY VCUT0714A-02Z-GS08 8000 8000 DEVICE NAME VCUT0714A-02Z PACKAGE DATA DEVICE NAME PACKAGE NAME TYPE CODE WEIGHT MOLDING COMPOUND FLAMMABILITY RATING MOISTURE SENSITIVITY LEVEL SOLDERING CONDITIONS SOD-923 A 0.45 mg UL 94 V-0 MSL level 1 (according J-STD-020) 260 °C/10 s at terminals VCUT0714A-02Z ABSOLUTE MAXIMUM RATINGS VCUT0714A-02Z PARAMETER Peak pulse current Peak pulse power ESD immunity Operating temperature TEST CONDITIONS Pin 1 to pin 2 acc. IEC 61000-4-5, 8/20 μs/single shot Pin 2 to pin 1 acc. IEC 61000-4-5, 8/20 μs/single shot Pin 1 to pin 2 acc. IEC 61000-4-5, 8/20 μs/single shot Pin 2 to pin 1 acc. IEC 61000-4-5, 8/20 μs/single shot Contact discharge acc. IEC 61000-4-2; 10 pulses Air discharge acc. IEC 61000-4-2; 10 pulses Junction temperature Storage temperature SYMBOL VALUE UNIT 5 A 2 A 63 W 54 W IPPM PPP ± 25 kV ± 30 kV TJ - 40 to + 125 °C TSTG - 55 to + 150 °C VESD ** Please see document “Vishay Material Category Policy”: www.vishay.com/doc?99902 Document Number: 81627 Rev. 1.8, 09-Aug-09 For technical questions, contact: ESDprotection@vishay.com www.vishay.com 1 VCUT0714A-02Z Bidirectional Asymmetrical (BiAs) Single Line ESD-Protection Diode in SOD923 Vishay Semiconductors CUT THE SPIKES WITH VCUT0714A-02Z The VCUT0714A-02Z is a bidirectional but asymmetrical (BiAs) ESD-protection device which clamps positive and negative overvoltage transients to ground. Connected between the signal or data line and the ground the VCUT0714A-02Z offers a high isolation (low leakage current, small capacitance) within the specified working range of - 7 V to + 14 V or - 14 V and + 7 V. Due to the short leads and small package size of the tiny SOD-923 package the line inductance is very low, so that fast transients like an ESD-strike can be clamped with minimal over- or undershoots. - 14 V ≤ VRW ≤ + 7 V 1 1 2 - 7 V ≤ VRW ≤ + 14 V 2 Ground Ground 22288 ELECTRICAL CHARACTERISTICS VCUT0714A-02Z PARAMETER TEST CONDITIONS/REMARKS SYMBOL MIN. TYP. MAX. UNIT Number of lines which can be protected Nchannel - - 1 lines Reverse working voltage at I = 1 μA VRWM 14 - - V Reverse current at V = 14 V IR - - 0.1 μA Reverse breakdown voltage at I = 1 mA VBR 14.5 - - V - - 27 V - - 30 V - 8 8.5 pF - 4 - pF Protection paths Reverse clamping voltage Capacitance at IPP = 1 A at IPP = IPPM = 2 A at V = 0 V; f = 1 MHz at V = 7 V; f = 1 MHz VC CD Note • Ratings at 25 °C, ambient temperature unless otherwise specified. Measured from pin 2 to pin 1. ELECTRICAL CHARACTERISTICS VCUT0714A-02Z PARAMETER TEST CONDITIONS/REMARKS SYMBOL MIN. TYP. MAX. UNIT Number of lines which can be protected Nchannel - - 1 lines Reverse working voltage at I = 1 μA VRWM 7 - - V Reverse current at V = 7 V IR - - 0.1 μA Reverse breakdown voltage at I = 1 mA VBR 7.3 - - V - - 13 V - - 17 V - 8 8.5 pF - 6.4 - pF Protection paths Reverse clamping voltage Capacitance at IPP = 1 A at IPP = IPPM = 5 A at V = 0 V; f = 1 MHz at V = 3.5 V; f = 1 MHz VC CD Note • Ratings at 25 °C, ambient temperature unless otherwise specified. Measured from pin 1 to pin 2. www.vishay.com 2 For technical questions, contact: ESDprotection@vishay.com Document Number: 81627 Rev. 1.8, 09-Aug-09 VCUT0714A-02Z Bidirectional Asymmetrical (BiAs) Single Line ESD-Protection Diode in SOD923 Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 120 % 25 Rise time = 0.7 ns to 1 ns Discharge Current IESD 100 % Pin 2 to 1 20 VR (V) 80 % 60 % 53 % 15 10 Pin 1 to 2 40 % 27 % 5 20 % 0% - 10 0 10 20 30 40 50 60 70 80 90 100 Time (ns) 20557 0 0.01 0.1 1 20577 Fig. 1 - ESD Discharge Current Wave Form acc. IEC 61000-4-2 (330 Ω/150 pF) 10 IR (µA) 100 1000 10 000 Fig. 4 - Typical Reverse Voltage VR vs. Reverse Current IR 35 8 µs to 100 % 100 % Pin 2 to 1 30 80 % 25 60 % 20 VC (V) IPPM VC 20 µs to 50 % 15 Pin 1 to 2 40 % 10 20 % 0% 0 0 10 20548 20 30 40 Time (µs) 0 1 2 3 4 5 6 7 IPP (A) 20578 Fig. 2 - 8/20 μs Peak Pulse Current Wave Form acc. IEC 61000-4-5 Fig. 5 - Typical Peak Clamping Voltage VC vs. Peak Pulse Current IPP 80 9 f = 1 MHz 8 7 Acc. IEC 61000-4-2 + 8 kV contact discharge 70 60 Pin 1 to 2 VC-ESD (V) 6 CD (pF) Measured acc. IEC 61000-4-5 (8/20 µs - wave form) 5 5 Pin 2 to 1 4 50 40 30 3 20 2 10 1 Pin 1 to 2 0 0 0 2 20576 4 6 8 10 12 14 16 VR (V) 10 20 30 40 50 60 70 80 90 20579 Fig. 3 - Typical Capacitance CD vs. Reverse Voltage VR Document Number: 81627 Rev. 1.8, 09-Aug-09 - 10 - 10 0 t (ns) Fig. 6 - Typical Clamping Performance at + 8 kV Contact Discharge (acc. IEC 61000-4-2) For technical questions, contact: ESDprotection@vishay.com www.vishay.com 3 VCUT0714A-02Z Vishay Semiconductors Bidirectional Asymmetrical (BiAs) Single Line ESD-Protection Diode in SOD923 10 180 Acc. IEC 61000-4-2 - 8 kV contact discharge - 10 140 - 20 120 - 30 - 40 Pin 1 to 2 - 50 Pin 2 to 1 Acc. IEC 61000-4-2 contact discharge 160 VC-ESD (V) VC-ESD (V) 0 Pin 1 to 2 100 80 60 - 60 40 - 70 20 - 80 - 10 0 VC-ESD 0 10 20 30 40 50 60 70 80 90 20580 0 t (ns) 5 Fig. 7 - Typical Clamping Performance at - 8 kV Contact Discharge (acc. IEC 61000-4-2) 10 15 20 25 30 VESD (kV) 20575 Fig. 8 - Typical Peak Clamping Voltage at ESD Contact Discharge (acc. IEC 61000-4-2) PACKAGE DIMENSIONS in millimeters (inches): SOD-923 0.55 (0.022) max. 0.41 (0.016) max. 0.05 (0.002) 0.85 (0.033) 0.75 (0.030) 0.65 (0.026) 0.15 (0.006) 0.25 (0.010) 0.39 (0.015) 0.37 (0.015) 0.07 (0.003) 0.13 (0.005) 5° ref. Foot print recommendation: 1.1 (0.043) 0.9 (0.035) 0.35 (0.014) Document no.: S8-V-3880.05-001 (4) Rev. 1 - Date: 05.July.2006 0.9 (0.035) 20096 0.3 (0.012) www.vishay.com 4 For technical questions, contact: ESDprotection@vishay.com Document Number: 81627 Rev. 1.8, 09-Aug-09 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1